Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR › 2011.12–2014.12
RM2170E _59 Vehicle Exterior _057046 DOOR / HATCH _0278161 REAR DOOR A

DOOR / HATCH  REAR DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure described below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 69204A 4.INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.

Apply MP grease to the sliding parts of the rear door outside handle frame sub-assembly.


b.
B307163E03
0.135,2.615 0.385,2.813 0.25,0.198 10 true *b 0.135,0.156 0.375,0.354 0.24,0.198 10 true *a

Engage the door handle nut and claw.

Text in Illustration
*a Outside
*b Inside


c.

Using a T30 "TORX" socket wrench, install the rear door outside handle frame sub-assembly with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69242G 5.INSTALL REAR DOOR OUTSIDE HANDLE REAR PAD

a.
B307161

Engage the 2 claws and install the rear door outside handle rear pad.


Hide 69241G 6.INSTALL REAR DOOR OUTSIDE HANDLE FRONT PAD

a.
B307160

Engage the 3 claws to install the rear door outside handle front pad.


Hide 69240 7.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY

a.
B307164

Insert the front end of the rear door outside handle assembly into the rear door outside handle frame.

NOTICE:

If the bellcrank lever is not pulled and held when installing the outside handle, the bellcrank lever will interfere with the outside handle and the release plate will be damaged.



b.

Insert the rear end of the rear door outside handle assembly into the rear door outside handle frame. Next, slide the rear door outside handle assembly toward the front of the vehicle to install it.


Hide 69227L 8.INSTALL REAR DOOR OUTSIDE HANDLE COVER

a.
B307158

Engage the claw to install the rear door outside handle cover.


b.

Using a T30 "TORX" socket wrench, install the rear door outside handle cover with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69780B 9.INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY

a.
B307165

Install the rear door inside locking cable assembly as shown in the illustration.


b.
B307166

Engage the 3 claws as shown in the illustration.


Hide 69740D 10.INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

a.
B307167

Install the rear door lock remote control cable assembly as shown in the illustration.


b.
B307168

Engage the claw as shown in the illustration.


Hide 69340 11.INSTALL REAR DOOR LOCK ASSEMBLY

NOTICE:
·

When reusing the removed rear door lock assembly, replace the door lock wiring harness seal on the connector with a new one.

·

Do not allow grease or dust to adhere to the door lock wiring harness seal surface of the connector.

·

Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water intrusion. This may result in a malfunction of the rear door lock assembly.



a.

Apply MP grease to the sliding parts of the rear door lock assembly.


b.

When reusing the rear door lock assembly:

i.
B307153

Install a new door lock wiring harness seal to the rear door lock assembly.



c.
B307170E01
0.354,0.98 0.354,1.352 false 0.271,1.376 0.611,1.518 0.340,0.142 10 *1

Insert the rear door lock assembly to the rear door outside handle release plate, and set it to the rear door panel.

Text in Illustration
*1 Release Plate

NOTICE:

Make sure that the rear door outside handle frame release plate is securely connected to the rear door lock assembly.



d.

Using a T30 "TORX" socket wrench, install the rear door lock assembly with the 3 screws.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


e.

Connect the connector.


f.
B307151

Install the rear door lock child protection cover.


Hide 68124B 12.INSTALL REAR DOOR QUARTER WINDOW GLASS

a.

Install the rear door quarter window weatherstrip to the rear door quarter window glass.


b.
B307171

Install the rear door quarter window glass with the rear door quarter window weatherstrip as shown in the illustration.


Hide 68230C 13.INSTALL REAR DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY

Hide 85720E 14.INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY

NOTICE:

The regulator arm must be below the intermediate position when installing the rear power window regulator motor assembly.


a.
B307149

Using a T25 "TORX" socket wrench, install the power window regulator motor assembly with the 3 screws.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

HINT:

A new rear window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.



Hide 69830A 15.INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY

a.

Apply MP grease to the sliding parts of the rear door window regulator assembly.


b.

Install the temporary bolt to the rear door window regulator assembly.


c.
B307148E04
2.052,0.948 1.49,0.833 true 2,1.76 2.208,1.948 0.208,0.188 10 true (1) 2.729,0.365 2.938,0.552 0.208,0.188 10 true (2) 2.875,1.271 3.083,1.458 0.208,0.188 10 true (3) 1.656,0.448 1.865,0.635 0.208,0.188 10 true (4) 1.281,0.75 1.448,0.906 0.167,0.156 10 true *1

Temporarily install the rear door window regulator assembly.

Text in Illustration
*1 Temporary Bolt


d.

Tighten the temporary bolt and 3 bolts to install the rear door window regulator assembly in the order shown in the illustration.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Connect the connector.


Hide 69975A 16.INSTALL REAR DOOR GLASS CHANNEL FILLER

a.

Apply soapy water to a new rear door glass channel filler.


b.
B307172E01
2.578,0.191 2.738,0.368 0.161,0.177 10 *b 0.584,0.191 0.745,0.368 0.161,0.177 10 *a 2.902,0.571 3.015,0.764 0.113,0.193 10 B 0.358,0.571 0.471,0.764 0.113,0.193 10 A 0.383,1.242 0.201,1.117 false 3.185,1.001 3.362,1.163 0.177,0.162 10 *c 0.005,1.001 0.182,1.163 0.177,0.162 10 *c 3.007,1.243 3.185,1.121 false

Install the new rear door glass channel filler as shown in the illustration.

Text in Illustration
*a Front Side
*b Rear Side
*c Edge of curved surface

Area Measurement
A 5.0 mm (0.197 in.)
B 5.0 mm (0.197 in.)


Hide 69906B 17.INSTALL REAR DOOR GLASS CHANNEL SUB-ASSEMBLY

a.

Apply soapy water to a rear door glass channel.


b.
B307173E01
2.542,0.205 2.758,0.402 0.216,0.197 10 *b 0.651,0.205 0.868,0.402 0.216,0.197 10 *a 2.929,0.562 3.096,0.746 0.166,0.183 10 B 0.368,0.562 0.535,0.746 0.166,0.183 10 A 3.019,1.232 3.21,1.142 false 3.221,1.006 3.392,1.173 0.171,0.167 10 *c 0.396,1.23 0.276,1.165 false 0.092,1.058 0.264,1.224 0.171,0.167 10 *c

Using a plastic-faced hammer, tap the channel onto the glass to install the glass channel sub-assembly.

Text in Illustration
*a Front Side
*b Rear Side
*c Edge of curved surface

Area Measurement
A 5.0 mm (0.197 in.)
B 5.0 mm (0.197 in.)

NOTICE:
·

Be careful not to damage the glass or glass channel.

·

Make sure the position of the rear door glass channel filler does not change.




Hide 68104 18.INSTALL REAR DOOR GLASS SUB-ASSEMBLY

a.
B307174E01
1.836,0.222 2.051,0.413 0.215,0.191 10 (1) 0.714,1.212 0.929,1.403 0.215,0.191 10 (2)

Insert the rear door glass as indicated by the arrows in the order shown in the illustration.

NOTICE:

Do not damage the rear door glass.



b.

Slide the lower section of the rear door glass sub-assembly and engage the rear door glass sub-assembly to the rear door window regulator assembly.


Hide 67408E 19.INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

a.
B307144

Temporary install the rear door window division bar sub-assembly with the 2 bolts.

NOTICE:

Do not damage the rear door glass.



b.

Install the rear door window division bar sub-assembly with the 2 bolts and screw.


Hide 68152C 20.INSTALL REAR DOOR GLASS RUN

a.
B307143

Install the rear door glass run.


Hide 67872 21.INSTALL REAR DOOR WEATHERSTRIP

a.

Clean the rear door panel sub-assembly.


b.
B307142E03
0.479,0.177 0.75,0.177 false 0.771,0.083 0.948,0.271 0.177,0.188 10 false *1

Engage the 30 clips to install a new front door weatherstrip.

Text in Illustration
*1 Double-sided tape


Hide 68630 22.INSTALL REAR DOOR CHECK ASSEMBLY

a.

Apply MP grease to the sliding areas of the rear door check assembly.


b.
B307141E04
2.74,1.302 2.958,1.479 0.219,0.177 10 true (A) 1.563,1.646 1.781,1.823 0.219,0.177 10 true (B) 1.552,0.385 1.771,0.563 0.219,0.177 10 true (B)

Apply adhesive to the threads of the bolt (A).

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.

Install the rear door check assembly with the 3 bolts.

Torque:
Bolt (A) : 30 N*m (306 kgf*cm, 22 ft.*lbf)
Bolt (B) : 8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 67842E 23.INSTALL REAR DOOR SERVICE HOLE COVER

a.

Apply butyl tape to the rear door panel.


b.

Pass the rear door lock remote control cable, rear door inside locking cable and each connector through a new rear door service hole cover.


c.
B307175E02
0.406,1.594 0.313,1.594 false 2.969,0.375 3.083,0.375 false 2.927,1.563 2.927,1.656 false 0.115,1.5 0.292,1.656 0.177,0.156 10 true *a 3.146,0.292 3.323,0.448 0.177,0.156 10 true *a 2.844,1.667 3.063,1.854 0.219,0.188 10 true *a

Attach the rear door service hole cover according to the reference points on the rear door panel.

Text in Illustration
*a Reference Point

NOTICE:

Securely install the rear door service hole cover preventing wrinkles and air bubbles.



Hide 68174A 25.INSTALL REAR DOOR GLASS INNER WEATHERSTRIP

a.
B307177

Engage the 5 claws to install the rear door glass inner weatherstrip as shown in the illustration.


Hide 69206C 26.INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B307136

Engage the 4 guides to install the rear door inside handle sub-assembly.


Hide 67604 27.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

a.
B307178E02
2.302,0.979 2.635,0.688 false 2.333,1.146 2.583,1.354 false 2.656,0.594 2.854,0.802 0.198,0.208 10 true *1 2.604,1.292 2.802,1.49 0.198,0.198 10 true *2

Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly to the rear door inside handle.

Text in Illustration
*1 Rear Door Inside Locking Cable Assembly
*2 Rear Door Lock Remote Control Cable Assembly


b.
B307182

Engage the 7 clips.


c.
B308235

Engage the clip.


d.
B307134

Install the rear door trim board sub-assembly with the 3 screws.


e.
B307179

Engage the claw and close the cover.


Hide 28.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

a.

Connect the connector.


b.
B307129

Engage the 3 guides and 8 claws to install the rear power window regulator switch assembly with rear door armrest base panel.


Hide 67674A 29.INSTALL REAR DOOR FRAME GARNISH

a.
B307128

Engage the guide.


b.

Engage the 2 clips and 3 claws to install the rear door frame garnish.


Hide 30.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).