Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2014.12–2017.06
RM2170E _56 Audio / Visual / Telematics _057029 AUDIO / VIDEO _0278060 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Illumination Circuit  


DESCRIPTION

Power is supplied to the radio receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

E256149E01
3.682,1.683 3.777,1.834 0.095,0.151 10 5 3.647,1.873 3.836,2.024 0.189,0.151 10 z2 4.689,1.683 4.861,1.834 0.173,0.151 10 12 4.687,1.873 4.974,2.024 0.287,0.151 10 G5 4.116,1.783 4.410,1.934 0.294,0.151 10 IL+2 3.682,2.558 3.777,2.709 0.095,0.151 10 8 2.409,1.782 2.503,1.933 0.095,0.151 10 2 2.409,2.657 2.503,2.807 0.095,0.151 10 5 3.647,2.745 3.836,2.895 0.189,0.151 10 z2 4.738,2.558 4.911,2.709 0.173,0.151 10 4 4.687,2.745 4.982,2.895 0.294,0.151 10 G5 4.116,2.658 4.430,2.809 0.314,0.151 10 EAU 2.552,1.871 2.846,2.021 0.294,0.151 10 IL+2 2.552,2.745 2.866,2.896 0.314,0.151 10 EAU 3.797,3.202 4.709,3.717 0.912,0.515 10 Spiral Cable with Sensor Sub-assembly 0.311,3.202 1.866,3.352 1.556,0.151 10 Steering Pad Switch LH 0.387,0.859 1.808,1.216 1.421,0.357 10 from Auxiliary Battery 3.262,1.121 3.574,1.271 0.312,0.151 10 TAIL 4.143,1.002 4.620,1.152 0.477,0.151 10 PANEL 5.125,0.467 6.314,0.812 1.189,0.345 10 to Main Body ECU 6.082,3.983 7.075,4.301 0.994,0.317 10 Radio Receiver Assembly 6.221,1.873 6.515,2.024 0.295,0.151 10 ILL+ 5.877,1.719 6.049,1.870 0.172,0.151 10 10 6.082,3.849 6.361,3.999 0.279,0.151 10 G37 2.411,3.337 3.405,3.654 0.994,0.317 10 Steering Pad Switch RH 2.411,3.202 2.767,3.352 0.355,0.151 10 SR1

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK ILLUMINATION
a.

Check if the illumination for the radio receiver assembly, steering pad switch assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.

Result:
Result Proceed to
Illumination comes on for all components except steering pad switch assembly. A
Illumination comes on for all components except radio receiver assembly. B
No illumination comes on (radio receiver assembly, hazard switch, heater control switch, etc.). C




A

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

B

7.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

C

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.

Disconnect the spiral cable with sensor sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G5-12 (IL+2) - Body ground Power switch off
Light control switch in the tail or head position
11 to 14 V




OK

3.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Disconnect the steering pad switch assembly connector.


b.

Connect an auxiliary battery positive (+) lead to terminal IL+2 and a negative (-) lead to terminal EAU of the steering pad switch assembly connector.

U183730E01
4.156,1.932 3.756,2.332 false 3.559,2.451 3.159,2.851 false 2.873,2.283 3.048,2.446 0.174,0.163 10 z2 4.181,1.862 4.499,2.023 0.317,0.161 10 IL+2 3.006,2.863 3.323,3.024 0.317,0.161 10 EAU 0.169,0.077 0.486,0.238 0.317,0.161 10 *a


c.

Check if the illumination for the steering pad switch assembly comes on.

OK:

Illumination for the steering pad switch assembly comes on.


Text in Illustration
*a Component without harness connected
(Steering Pad Switch Assembly)
- -


d.

Proceed to the next step based on the inspection result.

Result:
Result Proceed to
NG A
OK B




A

4.INSPECT STEERING PAD SWITCH RH

B

5.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
4.INSPECT STEERING PAD SWITCH RH
a.

Disconnect the steering pad switch RH connectors.

U183747E01
0.14,0.131 0.608,0.360 0.467,0.229 10 *a 2.856,2.56 3.111,2.790 0.255,0.229 10 z2 3.141,2.993 3.451,3.139 0.310,0.146 10 EAU 4.156,2.133 4.466,2.279 0.310,0.146 10 IL+2 0.729,1.357 1.043,1.586 0.313,0.229 10 SR1 3.683,2.734 3.432,2.985 false 4.166,2.28 3.915,2.531 false 1.052,1.724 1.362,1.870 0.310,0.146 10 IL+2 2.15,1.724 2.460,1.870 0.310,0.146 10 EAU 1.566,1.465 1.315,1.716 false 1.963,1.465 2.21,1.711 false


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
SR1-2 (IL+2) - z2-5 (IL+2) Always Below 1 Ω
SR1-5 (EAU) - z2-8 (EAU) Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Steering Pad Switch RH)
- -



OK

REPLACE STEERING PAD SWITCH LH

NG

REPLACE STEERING PAD SWITCH RH

5.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
a.

Disconnect the steering pad switch assembly connector.


b.

Disconnect the spiral cable with sensor sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

E343950E06
3.448,3.552 3.802,3.76 0.354,0.208 3.646,0.406 4,0.615 0.354,0.208 3.698,4.375 3.698,4.115 false 4.083,3.979 3.927,3.979 false 3.594,0.927 3.438,0.927 false 3.865,1.24 3.865,1.083 false 2.073,0.219 2.385,0.417 0.313,0.198 10 false *a 3.031,0.271 3.344,0.469 0.313,0.198 10 false *b 3.76,0.438 4.073,0.635 0.313,0.198 10 false z2 2.813,3.427 3.125,3.625 0.313,0.198 10 false *c 3.521,3.583 3.979,3.781 0.458,0.198 10 false G5 3.083,0.844 3.448,1.042 0.365,0.198 10 false IL+2 3.708,1.25 4.073,1.448 0.365,0.198 10 false EAU 3.552,4.396 3.917,4.594 0.365,0.198 10 false EAU 4.104,3.885 4.469,4.083 0.365,0.198 10 false IL+2

Standard Resistance:
Tester Connection Condition Specified Condition
z2-5 (IL+2) - G5-12 (IL+2) Center Below 3 Ω
2.5 rotations to the left
2.5 rotations to the right
z2-8 (EAU) - G5-4 (EAU) Center Below 3 Ω
2.5 rotations to the left
2.5 rotations to the right



d.

After setting the spiral cable with sensor sub-assembly to the center position, rotate the spiral cable with sensor sub-assembly 2.5 times clockwise. Then while rotating the spiral cable with sensor sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z2-5 (IL+2) - G5-12 (IL+2) Always Below 3 Ω
z2-8 (EAU) - G5-4 (EAU) Always Below 3 Ω


NOTICE:
·

The spiral cable with sensor sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable with sensor sub-assembly may prevent the airbag from deploying. Refer to the pages shown in the brackets.

·

As the spiral cable with sensor sub-assembly may break, do not rotate the spiral cable with sensor sub-assembly more than the specified amount.



HINT:


Text in Illustration
*a Component without harness connected
(Spiral Cable with Sensor Sub-assembly)
*b Steering Pad Switch Assembly Side
*c Vehicle Side



OK

6.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - BODY GROUND)

NG

REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - BODY GROUND)
a.

Disconnect the spiral cable with sensor sub-assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G5-4 (EAU) - Body ground Always Below 1 Ω




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.

Disconnect the radio receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G37-10 (ILL+) - Body ground Power switch off
Light control switch in the tail or head position
11 to 14 V




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR