This circuit sends an operation signal from the steering pad switch assembly to the radio receiver assembly.
If there is an open in the circuit, the audio system cannot be operated using the steering pad switch assembly.
If there is a short in the circuit, the same condition as when a switch is continuously depressed occurs.
Therefore, the radio receiver assembly cannot be operated using the steering pad switch assembly, and also the radio receiver assembly itself cannot function.
The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).
Disconnect the radio receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G41-21 (SW1) - Body ground | No switch pushed | 95 to 105 kΩ |
| Seek+ switch pushed | Below 2.5 Ω | |
| Seek- switch pushed | 323 to 335 Ω | |
| Volume+ switch pushed | 980 to 1020 Ω | |
| Volume- switch pushed | 3048 to 3172 Ω | |
| G41-22 (SW2) - Body ground | No switch pushed | 95 to 105 kΩ |
| MODE switch pushed | Below 2.5 Ω |
OK
NG
Disconnect the steering pad switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z2-10 (AU1) - z2-8 (EAU) | No switch pushed | 95 to 105 kΩ |
| Seek+ switch pushed | Below 2.5 Ω | |
| Seek- switch pushed | 323 to 335 Ω | |
| Volume+ switch pushed | 980 to 1020 Ω | |
| Volume- switch pushed | 3048 to 3172 Ω | |
| z2-9 (AU2) - z2-8 (EAU) | No switch pushed | 95 to 105 kΩ |
| MODE switch pushed | Below 2.5 Ω |
| *a | Component without harness connected
(Steering Pad Switch Assembly) |
*b | Seek+ |
| *c | Seek- | *d | Volume+ |
| *e | Volume- | *f | MODE |
Proceed to the next step based on the inspection result.
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Disconnect the steering pad switch RH connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| SR1-3 (AU1) - z2-10 (AU1) | Always | Below 1 Ω |
| SR1-4 (AU2) - z2-9 (AU2) | Always | Below 1 Ω |
| SR1-5 (EAU) - z2-8 (EAU) | Always | Below 1 Ω |
| *a | Component without harness connected
(Steering Pad Switch RH) |
- | - |
OK
NG
Disconnect the steering pad switch assembly connector.
Disconnect the spiral cable with sensor sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z2-8 (EAU) - G5-4 (EAU) | Center | Below 3 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| z2-10 (AU1) - G5-6 (AU1) | Center | Below 3 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| z2-9 (AU2) - G5-5 (AU2) | Center | Below 3 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right |
After setting the spiral cable with sensor sub-assembly to the center position, rotate the spiral cable with sensor sub-assembly 2.5 times clockwise. Then while rotating the spiral cable with sensor sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z2-8 (EAU) - G5-4 (EAU) | Always | Below 3 Ω |
| z2-10 (AU1) - G5-6 (AU1) | Always | Below 3 Ω |
| z2-9 (AU2) - G5-5 (AU2) | Always | Below 3 Ω |
The spiral cable with sensor sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable with sensor sub-assembly may prevent the airbag from deploying. Refer to the pages shown in the brackets.
As the spiral cable with sensor sub-assembly may break, do not rotate the spiral cable with sensor sub-assembly more than the specified amount.
Removal (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL)
Installation (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION)
| *a | Component without harness connected
(Spiral Cable with Sensor Sub-assembly) |
| *b | Steering Pad Switch Assembly Side |
| *c | Vehicle Side |
OK
NG