Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2014.12–2017.06
RM2170E _56 Audio / Visual / Telematics _057029 AUDIO / VIDEO _0278060 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Steering Pad Switch Circuit  


DESCRIPTION

This circuit sends an operation signal from the steering pad switch assembly to the radio receiver assembly.

If there is an open in the circuit, the audio system cannot be operated using the steering pad switch assembly.

If there is a short in the circuit, the same condition as when a switch is continuously depressed occurs.

Therefore, the radio receiver assembly cannot be operated using the steering pad switch assembly, and also the radio receiver assembly itself cannot function.

WIRING DIAGRAM

E256148E02
0.146,1.021 0.698,1.198 0.552,0.177 10 false Volume- 0.844,3.448 2.781,3.625 1.938,0.177 10 false Steering Pad Switch LH 0.875,1.021 1.469,1.198 0.594,0.177 10 false Volume+ 5.198,0.51 5.49,0.688 0.292,0.177 10 false AU1 5.198,1.469 5.5,1.646 0.302,0.177 10 false EAU 5.198,2.813 5.49,2.99 0.292,0.177 10 false AU2 6.563,0.604 6.938,0.781 0.375,0.177 10 false SW1 6.563,2.896 6.938,3.073 0.375,0.177 10 false SW2 6.5,3.406 6.875,3.583 0.375,0.177 10 false G41 1.729,1.01 2.198,1.188 0.469,0.177 10 false Seek- 4.76,0.615 4.948,0.792 0.188,0.177 10 false z2 4.76,1.573 4.948,1.75 0.188,0.177 10 false z2 4.76,2.917 4.948,3.094 0.188,0.177 10 false z2 4.75,0.417 4.927,0.594 0.177,0.177 10 false 10 4.802,1.365 4.896,1.542 0.094,0.177 10 false 8 4.802,2.729 4.896,2.906 0.094,0.177 10 false 9 5.771,0.625 6.063,0.802 0.292,0.177 10 false G5 5.76,1.573 6.052,1.75 0.292,0.177 10 false G5 5.771,2.917 6.052,3.094 0.281,0.177 10 false G5 6.323,0.521 6.5,0.698 0.177,0.177 10 false 21 6.323,2.823 6.5,3 0.177,0.177 10 false 22 5.813,1.365 5.906,1.542 0.094,0.177 10 false 4 5.823,0.417 5.917,0.594 0.094,0.177 10 false 6 5.823,2.729 5.917,2.906 0.094,0.177 10 false 5 3.948,0.594 4.24,0.771 0.292,0.177 10 false AU1 3.948,1.573 4.25,1.75 0.302,0.177 10 false EAU 3.948,2.906 4.24,3.083 0.292,0.177 10 false AU2 3.688,1.469 3.781,1.646 0.094,0.177 10 false 5 3.688,0.521 3.781,0.698 0.094,0.177 10 false 3 3.688,2.813 3.781,2.99 0.094,0.177 10 false 4 2.344,2.417 2.781,2.594 0.438,0.177 10 false MODE 4.896,3.417 5.792,4.052 0.896,0.635 10 false Spiral Cable with Sensor Sub-assembly 6.5,3.573 7.156,4.25 0.656,0.677 10 false Radio Receiver Assembly 3.656,3.406 4.031,3.583 0.375,0.177 10 false SR1 3.656,3.583 4.49,4.26 0.833,0.677 10 false Steering Pad Switch RH 2.344,1 2.813,1.177 0.469,0.177 10 false Seek+

CAUTION / NOTICE / HINT

NOTICE:

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STEERING PAD SWITCH SIGNAL)
a.

Disconnect the radio receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G41-21 (SW1) - Body ground No switch pushed 95 to 105 kΩ
Seek+ switch pushed Below 2.5 Ω
Seek- switch pushed 323 to 335 Ω
Volume+ switch pushed 980 to 1020 Ω
Volume- switch pushed 3048 to 3172 Ω
G41-22 (SW2) - Body ground No switch pushed 95 to 105 kΩ
MODE switch pushed Below 2.5 Ω




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT STEERING PAD SWITCH ASSEMBLY
2.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Disconnect the steering pad switch assembly connector.

U183731E02
3.688,2.698 3.688,3.042 false 4.031,3.042 3.792,2.698 false 3.344,3.042 3.583,2.698 false 1.677,1.25 2.156,0.76 false 1.677,1.594 2.198,1.865 false 1.396,1.583 1.042,1.844 false 1.396,1.24 1.083,0.927 false 1.458,1.365 0.896,1.26 false 2.938,2.479 3.104,2.646 0.167,0.167 10 false z2 3.552,3.052 3.875,3.24 0.323,0.188 10 false AU2 3.948,3.042 4.271,3.229 0.323,0.188 10 false AU1 3.146,3.052 3.469,3.24 0.323,0.188 10 false EAU 0.135,0.063 0.292,0.25 0.156,0.188 10 false *a 2.188,0.646 2.344,0.833 0.156,0.188 10 false *b 0.938,0.781 1.094,0.969 0.156,0.188 10 false *d 0.74,1.167 0.896,1.354 0.156,0.188 10 false *f 0.885,1.792 1.042,1.979 0.156,0.188 10 false *e 2.219,1.833 2.375,2.021 0.156,0.188 10 false *c


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z2-10 (AU1) - z2-8 (EAU) No switch pushed 95 to 105 kΩ
Seek+ switch pushed Below 2.5 Ω
Seek- switch pushed 323 to 335 Ω
Volume+ switch pushed 980 to 1020 Ω
Volume- switch pushed 3048 to 3172 Ω
z2-9 (AU2) - z2-8 (EAU) No switch pushed 95 to 105 kΩ
MODE switch pushed Below 2.5 Ω


Text in Illustration
*a Component without harness connected
(Steering Pad Switch Assembly)
*b Seek+
*c Seek- *d Volume+
*e Volume- *f MODE


c.

Proceed to the next step based on the inspection result.

Result:
Result Proceed to
NG A
OK B




A

3.INSPECT STEERING PAD SWITCH RH

B

4.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
3.INSPECT STEERING PAD SWITCH RH
a.

Disconnect the steering pad switch RH connectors.

U183746E01
0.14,0.131 0.588,0.360 0.448,0.229 10 *a 2.856,2.56 3.111,2.790 0.255,0.229 10 z2 3.141,2.993 3.451,3.139 0.310,0.146 10 EAU 3.645,2.993 3.955,3.139 0.310,0.146 10 AU2 4.07,2.993 4.380,3.139 0.310,0.146 10 AU1 0.729,1.357 1.043,1.586 0.313,0.229 10 SR1 1.164,1.724 1.474,1.870 0.310,0.146 10 AU1 1.697,1.724 2.007,1.870 0.310,0.146 10 AU2 2.15,1.724 2.460,1.870 0.310,0.146 10 EAU 1.684,1.463 1.441,1.706 false 1.829,1.469 1.829,1.713 false 1.986,1.461 2.231,1.706 false 3.683,2.73 3.436,2.976 false 3.794,2.732 3.794,2.974 false 3.895,2.734 4.134,2.972 false


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
SR1-3 (AU1) - z2-10 (AU1) Always Below 1 Ω
SR1-4 (AU2) - z2-9 (AU2) Always Below 1 Ω
SR1-5 (EAU) - z2-8 (EAU) Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Steering Pad Switch RH)
- -



OK

REPLACE STEERING PAD SWITCH LH

NG

REPLACE STEERING PAD SWITCH RH

4.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
a.

Disconnect the steering pad switch assembly connector.


b.

Disconnect the spiral cable with sensor sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

E343950E08
3.448,3.552 3.802,3.76 0.354,0.208 3.646,0.406 4,0.615 0.354,0.208 3.375,4.344 3.698,4.115 false 3.823,4.365 3.823,4.115 false 3.625,1.073 3.51,1.229 false 4.073,1.24 3.865,1.083 false 3.74,1.094 3.74,1.24 false 4.146,4.323 3.938,4.125 false 2.073,0.219 2.385,0.417 0.313,0.198 10 false *a 3.031,0.271 3.344,0.469 0.313,0.198 10 false *b 3.76,0.438 4.073,0.635 0.313,0.198 10 false z2 2.813,3.427 3.125,3.625 0.313,0.198 10 false *c 3.521,3.583 3.979,3.781 0.458,0.198 10 false G5 3.281,1.24 3.646,1.438 0.365,0.198 10 false AU1 4,1.24 4.365,1.438 0.365,0.198 10 false EAU 3.198,4.375 3.563,4.573 0.365,0.198 10 false EAU 3.625,1.24 3.99,1.438 0.365,0.198 10 false AU2 3.667,4.375 4.031,4.573 0.365,0.198 10 false AU2 4.052,4.365 4.417,4.563 0.365,0.198 10 false AU1

Standard Resistance:
Tester Connection Condition Specified Condition
z2-8 (EAU) - G5-4 (EAU) Center Below 3 Ω
2.5 rotations to the left
2.5 rotations to the right
z2-10 (AU1) - G5-6 (AU1) Center Below 3 Ω
2.5 rotations to the left
2.5 rotations to the right
z2-9 (AU2) - G5-5 (AU2) Center Below 3 Ω
2.5 rotations to the left
2.5 rotations to the right



d.

After setting the spiral cable with sensor sub-assembly to the center position, rotate the spiral cable with sensor sub-assembly 2.5 times clockwise. Then while rotating the spiral cable with sensor sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z2-8 (EAU) - G5-4 (EAU) Always Below 3 Ω
z2-10 (AU1) - G5-6 (AU1) Always Below 3 Ω
z2-9 (AU2) - G5-5 (AU2) Always Below 3 Ω


NOTICE:
·

The spiral cable with sensor sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable with sensor sub-assembly may prevent the airbag from deploying. Refer to the pages shown in the brackets.

·

As the spiral cable with sensor sub-assembly may break, do not rotate the spiral cable with sensor sub-assembly more than the specified amount.



HINT:


Text in Illustration
*a Component without harness connected
(Spiral Cable with Sensor Sub-assembly)
*b Steering Pad Switch Assembly Side
*c Vehicle Side



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (RADIO RECEIVER ASSEMBLY, BODY GROUND - SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY)

NG

REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY