Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2011.12–2014.12
RM2170E _57 Power Source / Network _057033 NETWORKING _0278068 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Steering Angle Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Steering Angle Sensor Communication Stop Mode Either condition is met:
·

"Spiral cable (Steering Angle Sensor)" is not displayed on the "Communication Bus Check" screen of the intelligent tester (See page (Click here))

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Steering Angle Sensor Communication Stop Mode" in "DTC Combination Table" (See page (Click here))


·

Spiral cable with sensor sub-assembly (steering sensor) branch line or connector

·

Power source circuit of spiral cable with sensor sub-assembly (steering sensor)

·

Spiral cable with sensor sub-assembly (steering sensor) ground circuit

·

Spiral cable with sensor sub-assembly (steering sensor)



WIRING DIAGRAM

C252836E12
5.99,0 6.354,0 false 2.188,1.281 2.135,0.896 2.135,0.896 2.021,0.896 false 5.448,1.281 5.781,0.667 5.781,0.667 6.042,0.667 false 1.125,5 3,5.167 1.875,0.167 10 false : CAN Main Bus Line (CANH) 1.125,5.417 3.01,5.594 1.885,0.177 10 false : CAN Main Bus Line (CANL) 4.26,4.99 5.979,5.177 1.719,0.188 10 false : CAN Branch Line (CANH) 4.26,5.396 6,5.563 1.74,0.167 10 false : CAN Branch Line (CANL) 0.604,3.667 1.479,3.833 0.875,0.167 10 false Trouble Area 2.708,4.24 4.552,4.792 1.844,0.552 10 false Spiral Cable with Sensor Sub-assembly (Steering Sensor) 0.656,2.198 1.063,2.354 0.406,0.156 10 false 120 Ω 6.156,2.198 6.583,2.354 0.427,0.156 10 false 120 Ω 0.208,0.813 2.156,1.063 1.948,0.25 10 false CAN Junction Connector RH 4.938,0.542 5.333,0.698 0.396,0.156 10 false DLC3 2.969,3.292 3.396,3.438 0.427,0.146 10 false CANH 3.5,3.292 3.917,3.438 0.417,0.146 10 false CANL 2.75,3.375 2.927,3.521 0.177,0.146 10 false IG 1.896,4.031 2.344,4.188 0.448,0.156 10 false DOME 1.667,3.5 2.594,3.677 0.927,0.177 10 false ECU-IG NO. 1 3.833,3.563 4.146,3.719 0.313,0.156 10 false ESS 2.604,3.26 2.719,3.406 0.115,0.146 10 false 5 3.688,3.073 3.802,3.229 0.115,0.156 10 false 3 3.115,3.073 3.229,3.229 0.115,0.156 10 false 4 4.177,3.469 4.292,3.615 0.115,0.146 10 false 2 2.396,4.24 2.688,4.406 0.292,0.167 10 false G30 0.313,2.813 1.552,3.188 1.24,0.375 10 false Combination Meter Assembly 6.083,0.583 6.969,1.229 0.885,0.646 10 false CAN Junction Connector LH 6.385,2.813 6.75,2.958 0.365,0.146 10 false ECM 0.073,0.042 1.469,0.333 1.396,0.292 12 false V Bus (for LHD): 2.604,3.792 2.719,3.938 0.115,0.146 10 false 6 2.76,3.906 3.052,4.063 0.292,0.156 10 false BAT 0.083,2.813 0.292,2.969 0.208,0.156 10 false G1 6.073,2.813 6.344,2.969 0.271,0.156 10 false A40

C251622E09
1.833,1.281 1.49,0.604 1.49,0.604 1.208,0.604 false 4.625,0.833 4.854,0.833 4.854,0.833 5.208,1.281 false 1.125,5 3,5.167 1.875,0.167 10 false : CAN Main Bus Line (CANH) 1.125,5.417 3.01,5.594 1.885,0.177 10 false : CAN Main Bus Line (CANL) 4.271,4.99 5.99,5.177 1.719,0.188 10 false : CAN Branch Line (CANH) 4.271,5.396 6.01,5.563 1.74,0.167 10 false : CAN Branch Line (CANL) 0.677,3.708 1.552,3.875 0.875,0.167 10 false Trouble Area 2.719,4.25 4.771,4.688 2.052,0.438 10 false Spiral Cable with Sensor Sub-assembly (Steering Sensor) 0.729,2.208 1.135,2.365 0.406,0.156 10 false 120 Ω 6.229,2.208 6.656,2.365 0.427,0.156 10 false 120 Ω 0.24,0.521 1.188,1.177 0.948,0.656 10 false CAN Junction Connector RH 2.063,0.563 2.458,0.719 0.396,0.156 10 false DLC3 2.979,3.271 3.406,3.417 0.427,0.146 10 false CANH 3.51,3.271 3.927,3.417 0.417,0.146 10 false CANL 2.76,3.354 2.938,3.5 0.177,0.146 10 false IG 1.927,4.042 2.833,4.198 0.906,0.156 10 false DOME 1.698,3.51 2.906,3.792 1.208,0.281 10 false ECU-IG NO. 1 3.813,3.552 4.125,3.708 0.313,0.156 10 false ESS 2.615,3.271 2.729,3.417 0.115,0.146 10 false 5 3.688,3.083 3.802,3.24 0.115,0.156 10 false 3 3.125,3.083 3.24,3.24 0.115,0.156 10 false 4 4.188,3.458 4.302,3.604 0.115,0.146 10 false 2 2.427,4.25 2.719,4.417 0.292,0.167 10 false G30 0.365,2.823 1.604,3.198 1.24,0.375 10 false Combination Meter Assembly 2.823,0.75 4.594,1.052 1.771,0.302 10 false CAN Junction Connector LH 6.365,2.813 6.729,2.958 0.365,0.146 10 false ECM 0.083,0.063 1.406,0.271 1.323,0.208 12 false V Bus (for RHD): 2.604,3.802 2.719,3.948 0.115,0.146 10 false 6 2.76,3.885 3.052,4.042 0.292,0.156 10 false BAT 0.125,2.823 0.333,2.979 0.208,0.156 10 false G1 6.052,2.813 6.323,2.969 0.271,0.156 10 false A40

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the cruise control system on using the cruise control main switch (ON/OFF switch), wait at least 60 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more.

·

After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY BRANCH WIRE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U159562E01
1.591,1.067 1.873,1.215 0.282,0.147 10 G30 0.844,2.677 1.242,2.824 0.398,0.147 10 CANL 2.192,2.672 2.633,2.819 0.440,0.147 10 CANH 0.06,0.038 0.217,0.185 0.158,0.147 10 *a 1.639,2.317 1.505,2.752 1.505,2.752 1.32,2.752 false 1.88,2.317 1.962,2.752 1.962,2.752 2.178,2.752 false

Disconnect the spiral cable with sensor sub-assembly (steering sensor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G30-4 (CANH) - G30-3 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Spiral Cable with Sensor Sub-assembly (Steering Sensor))



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY (STEERING SENSOR))

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
U159563E01
1.591,1.081 1.873,1.228 0.282,0.147 10 G30 0.41,1.336 0.724,1.483 0.314,0.147 10 ESS 0.06,0.052 0.217,0.199 0.158,0.147 10 *a 1.376,2.109 1.055,1.416 1.055,1.416 0.791,1.416 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G30-2 (ESS) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Spiral Cable with Sensor Sub-assembly (Steering Sensor))


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.
U183641E01
1.591,1.067 1.873,1.215 0.282,0.147 10 G30 1.507,2.672 1.684,2.819 0.177,0.147 10 IG 0.06,0.038 0.217,0.185 0.158,0.147 10 *a 2.127,2.317 1.977,2.752 1.977,2.752 1.723,2.752 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G30-5 (IG) - Body ground Power switch on (IG) 11 to 14 V
G30-6 (BAT) - Body ground Power switch off 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Spiral Cable with Sensor Sub-assembly (Steering Sensor))



OK

REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)