Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2014.12–2015.11
RM2170E _57 Power Source / Network _057033 NETWORKING _0278068 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Skid Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Skid Control ECU Communication Stop Mode Either condition is met:
·

"Skid Control (ABS/VSC/TRAC)" is not displayed on the "Communication Bus Check" screen of the intelligent tester (See page (Click here))

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Skid Control ECU Communication Stop Mode" in "DTC Combination Table" (See page (Click here))


·

Brake booster with master cylinder assembly (skid control ECU) branch line or connector

·

Power source circuit of brake booster with master cylinder assembly (skid control ECU)

·

Brake booster with master cylinder assembly (skid control ECU) ground circuit

·

Brake booster with master cylinder assembly (skid control ECU)



WIRING DIAGRAM

C252835E10
2.375,1.281 2.24,0.938 2.24,0.938 2.104,0.938 false 4.219,1.292 3.823,0.594 3.823,0.594 3.531,0.594 false 6.219,2.854 6.552,3.021 0.333,0.167 10 false ECM 2.729,4.094 3.031,4.271 0.302,0.177 10 false A41 3.042,4.094 5.271,4.469 2.229,0.375 10 false Brake Booster with Master Cylinder Assembly (Skid Control ECU) 4.76,0.563 5.135,0.74 0.375,0.177 10 false DLC3 1.146,5.01 3.073,5.365 1.927,0.354 10 false : CAN Main Bus Line (CANH) 4.292,5.021 6.031,5.375 1.74,0.354 10 false : CAN Branch Line (CANH) 4.281,5.427 6.021,5.781 1.74,0.354 10 false : CAN Branch Line (CANL) 1.125,5.438 3.052,5.792 1.927,0.354 10 false : CAN Main Bus Line (CANL) 2.344,3.719 3.063,3.875 0.719,0.156 10 false ABS NO. 2 1.25,3.74 2.104,3.948 0.854,0.208 10 false Trouble Area 3.406,3.583 3.76,3.885 0.354,0.302 10 false BI 4.427,3.583 4.76,3.729 0.333,0.146 10 false GND 3.625,3.302 4.021,3.458 0.396,0.156 10 false CA1H 4.135,3.302 4.521,3.469 0.385,0.167 10 false CA1L 3.156,3.458 3.333,3.604 0.177,0.146 10 false 14 4.823,3.469 5,3.615 0.177,0.146 10 false 28 3.677,3.094 3.865,3.24 0.188,0.146 10 false 37 4.313,3.083 4.49,3.24 0.177,0.156 10 false 38 0.344,0.854 2.167,1.042 1.823,0.188 10 false CAN Junction Connector RH 0.167,0.125 1.417,0.354 1.25,0.229 12 false V Bus (for LHD): 1.76,0.521 3.771,0.708 2.01,0.188 10 false CAN Junction Connector LH 0.292,2.875 1.5,3.219 1.208,0.344 10 false Combination Meter Assembly 0.646,2.219 1.094,2.365 0.448,0.146 10 false 120 Ω 6.177,2.25 6.625,2.396 0.448,0.146 10 false 120 Ω

C251621E28
1.823,1.281 1.49,0.698 1.49,0.698 1.302,0.698 false 3.573,1.281 3.854,0.646 3.854,0.646 4.125,0.646 false 6.219,2.813 6.552,2.979 0.333,0.167 10 false ECM 2.781,4.083 3.281,4.26 0.5,0.177 10 false A41 3.104,4.083 5.281,4.583 2.177,0.5 10 false Brake Booster with Master Cylinder Assembly (Skid Control ECU) 2.063,0.552 2.438,0.729 0.375,0.177 10 false DLC3 1.135,4.99 3.063,5.344 1.927,0.354 10 false : CAN Main Bus Line (CANH) 4.271,5 6.01,5.354 1.74,0.354 10 false : CAN Branch Line (CANH) 4.271,5.417 6.01,5.771 1.74,0.354 10 false : CAN Branch Line (CANL) 1.135,5.406 3.063,5.76 1.927,0.354 10 false : CAN Main Bus Line (CANL) 2.406,3.719 3.615,4 1.208,0.281 10 false ABS NO. 2 1.208,3.813 2.063,4.021 0.854,0.208 10 false Trouble Area 3.385,3.563 3.729,3.823 0.344,0.26 10 false BI 4.427,3.563 4.844,3.708 0.417,0.146 10 false GND 3.635,3.292 4.073,3.448 0.438,0.156 10 false CA1H 4.125,3.292 4.542,3.458 0.417,0.167 10 false CA1L 3.167,3.469 3.344,3.615 0.177,0.146 10 false 14 4.823,3.458 5.083,3.615 0.26,0.156 10 false 28 3.677,3.083 3.865,3.229 0.188,0.146 10 false 37 4.302,3.083 4.479,3.24 0.177,0.156 10 false 38 0.344,0.604 1.25,1.083 0.906,0.479 10 false CAN Junction Connector RH 4.198,0.563 6.354,0.917 2.156,0.354 10 false CAN Junction Connector LH 0.385,2.823 1.594,3.167 1.208,0.344 10 false Combination Meter Assembly 0.688,2.198 1.104,2.344 0.417,0.146 10 false 120 Ω 6.188,2.198 6.635,2.344 0.448,0.146 10 false 120 Ω 0.063,0.063 2.271,0.417 2.208,0.354 12 false V Bus (for RHD):

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the cruise control system on using the cruise control main switch (ON/OFF switch), wait at least 60 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more.

·

After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK DTC (BRAKE CONTROL SYSTEM)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.

OK:

DTC C1241 is not output.




OK

2.CHECK FOR OPEN IN CAN BUS LINES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY BRANCH LINE)

NG

GO TO DIAGNOSIS PROCEDURES INDICATED BY OUTPUT DTC

2.CHECK FOR OPEN IN CAN BUS LINES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U159483E01
0.196,0.187 0.380,0.345 0.184,0.158 10 *a 1.566,0.857 1.854,1.015 0.288,0.158 10 A41 1.312,2.791 1.725,2.948 0.413,0.158 10 CA1H 2.396,2.791 2.809,2.948 0.413,0.158 10 CA1L 1.976,2.137 1.564,2.768 false 2.081,2.142 2.59,2.768 false

Disconnect the brake booster with master cylinder assembly (Skid Control ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A41-37 (CA1H) - A41-38 (CA1L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Brake Booster with Master Cylinder Assembly (Skid Control ECU))


Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (for LHD)

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (for RHD)

C

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)