Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2014.12–2015.11
RM2170E _57 Power Source / Network _057033 NETWORKING _0278068 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  ECM Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
ECM Communication Stop Mode Either condition is met:
·

"ECM (Engine)" is not displayed on the "Communication Bus Check" screen of the intelligent tester (See page (Click here))

·

Communication system DTCs (DTCs that start with U) that are output correspond to "ECM Communication Stop Mode" in "DTC Combination Table" (See page (Click here))


·

Power source circuit of ECM

·

ECM main line or connector

·

ECM ground circuit

·

ECM



WIRING DIAGRAM

C252847E09
4.856,5.016 5.750,5.369 0.893,0.353 10 Trouble Area 2.919,2.321 3.308,2.475 0.388,0.155 10 DLC3 1.276,0.589 3.779,0.921 2.503,0.332 10 : CAN Main Bus Line (CANH) 1.276,0.932 3.779,1.264 2.503,0.332 10 : CAN Main Bus Line (CANL) 1.276,1.268 3.005,1.600 1.729,0.332 10 : CAN Branch Line (CANH) 1.276,1.611 3.005,1.943 1.729,0.332 10 : CAN Branch Line (CANL) 4.706,4.583 5.053,4.738 0.347,0.155 10 ECM 0.99,5.479 2.800,5.640 1.810,0.161 10 CAN Junction Connector LH 0.215,4.572 1.507,4.923 1.292,0.351 10 Combination Meter Assembly 0.196,5.174 2.012,5.340 1.816,0.166 10 CAN Junction Connector RH 5.07,3.525 5.351,3.696 0.281,0.170 10 +B2 5.149,3.116 5.352,3.292 0.203,0.177 10 +B 4.941,3.973 5.350,4.118 0.408,0.145 10 IGSW 5.158,4.359 5.352,4.531 0.194,0.172 10 E1 4.357,3.73 4.745,3.885 0.387,0.155 10 CANL 4.362,3.104 4.780,3.265 0.418,0.161 10 CANH 0.609,3.988 1.000,4.169 0.391,0.181 10 120 Ω 4.409,3.955 4.800,4.136 0.391,0.181 10 120 Ω 5.399,4.361 5.681,4.508 0.282,0.148 10 C10 5.496,2.949 5.599,3.103 0.103,0.153 10 2 5.492,3.343 5.608,3.491 0.116,0.148 10 3 5.466,3.784 5.652,3.933 0.185,0.149 10 37 5.454,4.192 5.630,4.342 0.176,0.150 10 16 4.091,3.029 4.263,3.171 0.171,0.142 10 13 4.096,3.663 4.287,3.817 0.191,0.154 10 26 6.151,3.709 6.541,4.573 0.390,0.864 10 to IG2 NO. 2 Fuse 5.405,2.656 6.773,2.978 1.368,0.322 10 to EFI-MAIN Relay 2.224,4.555 2.156,5.255 2.156,5.255 2.024,5.255 false 3.12,4.554 2.997,5.555 2.997,5.555 2.805,5.555 false 4.049,3.2 4.331,3.348 0.281,0.149 10 A40 4.053,3.835 4.323,3.984 0.270,0.149 10 A40 0.141,0.081 1.462,0.342 1.321,0.261 12 V Bus (for LHD): 5.408,3.122 5.680,3.266 0.272,0.145 10 A40 5.408,3.518 5.680,3.662 0.272,0.145 10 A40 5.408,3.96 5.680,4.105 0.272,0.145 10 A40

C243998E11
2.177,4.552 2.135,5.26 2.135,5.26 1.979,5.26 false 3.198,4.552 3.073,5.552 3.073,5.552 2.875,5.552 false 4.854,5.021 5.75,5.375 0.896,0.354 10 false Trouble Area 1.813,2.313 2.198,2.469 0.385,0.156 10 false DLC3 1.281,0.573 3.781,0.906 2.5,0.333 10 false : CAN Main Bus Line (CANH) 1.281,0.917 3.781,1.25 2.5,0.333 10 false : CAN Main Bus Line (CANL) 1.281,1.25 3.01,1.583 1.729,0.333 10 false : CAN Branch Line (CANH) 1.281,1.594 3.01,1.927 1.729,0.333 10 false : CAN Branch Line (CANL) 4.708,4.583 5.052,4.74 0.344,0.156 10 false ECM 1.094,5.458 3.052,5.635 1.958,0.177 10 false CAN Junction Connector LH 0.302,4.552 1.667,4.969 1.365,0.417 10 false Combination Meter Assembly 0.198,5.167 2.167,5.344 1.969,0.177 10 false CAN Junction Connector RH 5.073,3.51 5.354,3.677 0.281,0.167 10 false +B2 5.146,3.094 5.344,3.271 0.198,0.177 10 false +B 4.938,3.958 5.344,4.104 0.406,0.146 10 false IGSW 5.156,4.344 5.354,4.521 0.198,0.177 10 false E1 4.354,3.719 4.74,3.875 0.385,0.156 10 false CANL 4.365,3.094 4.781,3.25 0.417,0.156 10 false CANH 0.615,3.969 1.01,4.146 0.396,0.177 10 false 120 Ω 4.406,3.948 4.802,4.125 0.396,0.177 10 false 120 Ω 5.427,4.365 5.698,4.51 0.271,0.146 10 false C9 5.479,2.927 5.583,3.083 0.104,0.156 10 false 2 5.479,3.344 5.594,3.49 0.115,0.146 10 false 3 5.448,3.76 5.635,3.906 0.188,0.146 10 false 37 5.438,4.177 5.615,4.323 0.177,0.146 10 false 16 4.094,3.01 4.26,3.156 0.167,0.146 10 false 13 4.094,3.646 4.281,3.802 0.188,0.156 10 false 26 6.146,3.854 6.542,4.635 0.396,0.781 10 false to IG2 NO. 2 Fuse 5.406,2.635 6.688,2.958 1.281,0.323 10 false to EFI-MAIN Relay 4.042,3.208 4.313,3.375 0.271,0.167 10 false A40 4.042,3.833 4.313,4 0.271,0.167 10 false A40 0.094,0.083 1.49,0.302 1.396,0.219 12 false V Bus (for RHD): 5.396,3.115 5.667,3.281 0.271,0.167 10 false A40 5.396,3.51 5.656,3.688 0.26,0.177 10 false A40 5.396,3.958 5.667,4.146 0.271,0.188 10 false A40

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>PROBLEM SYMPTOMS TABLE).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the cruise control system on using the cruise control main switch (ON/OFF switch), wait at least 60 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more.

·

After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (ECM MAIN LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U159411E03
2.573,1.625 2.938,1.625 2.938,1.625 2.938,2.406 false 2.573,1.542 2.573,0.948 2.573,0.948 2.813,0.948 false 0.146,0.094 0.385,0.333 0.24,0.24 10 false *a 2.885,0.844 3.323,1.042 0.438,0.198 10 false CANH 2.75,2.438 3.219,2.635 0.469,0.198 10 false CANL 1.76,0.708 2.229,0.99 0.469,0.281 10 false A40

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A40-13 (CANH) - A40-26 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

2.CHECK ECM POWER SOURCE CIRCUIT

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (ECM MAIN LINE)

2.CHECK ECM POWER SOURCE CIRCUIT

OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)