Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2015.11–2018.08
RM2170E _57 Power Source / Network _057033 NETWORKING _0278068 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check CAN Bus Line for Short to +B (LHD Models)  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and +B when no resistance exists between terminals 6 (CANH) and 16 (BAT) or 14 (CANL) and 16 (BAT) of the DLC3.

Symptom Trouble Area
No resistance exists between terminals 6 (CANH) and 16 (BAT) or 14 (CANL) and 16 (BAT) of the DLC3.
·

Short to +B in CAN main bus line

·

Short to +B in CAN branch line

·

ECM

·

Brake booster with master cylinder assembly (Skid control ECU)

·

Main body ECU (Multiplex network body ECU)

·

Air conditioning amplifier assembly

·

Power steering ECU assembly

·

Smart key ECU assembly (Certification ECU)

·

Airbag sensor assembly

·

Spiral cable with sensor sub-assembly (Steering sensor)

·

Hybrid vehicle control computer assembly

·

Combination meter assembly

·

CAN junction connector LH

·

CAN junction connector RH



WIRING DIAGRAM

C349994E03
3.958,8.167 5.688,8.354 1.729,0.188 10 false : CAN Branch Line (CANH) 3.948,8.469 5.677,8.656 1.729,0.188 10 false : CAN Branch Line (CANL) 0.823,8.198 2.74,8.385 1.917,0.188 10 false : CAN Main Bus Line (CANH) 0.823,8.5 2.74,8.688 1.917,0.188 10 false : CAN Main Bus Line (CANL) 3.479,0.167 3.896,0.354 0.417,0.188 10 false 120 Ω 2.792,0.74 3.198,0.906 0.406,0.167 10 false CANL 0.385,0.396 0.75,0.563 0.365,0.167 10 false G1 4.146,1.167 4.365,1.385 0.219,0.219 10 false G 3.021,1.167 3.219,1.333 0.198,0.167 10 false W 0.635,0.396 2.49,0.594 1.854,0.198 10 false Combination Meter Assembly 0.094,0.01 1.948,0.208 1.854,0.198 12 false V Bus: 4.115,0.76 4.552,0.927 0.438,0.167 10 false CANH 4.104,0.969 4.448,1.188 0.344,0.219 10 false 31 3.052,0.969 3.365,1.177 0.313,0.208 10 false 32 5.167,0.51 6.375,0.698 1.208,0.188 10 false x: Suspected Area 4.75,6.927 6.74,7.177 1.99,0.25 10 false CAN Junction Connector RH 5.927,2.021 6.333,2.188 0.406,0.167 10 false CANL 5.917,1.448 6.354,1.615 0.438,0.167 10 false CANH 5.917,3.74 6.323,3.906 0.406,0.167 10 false CANL 5.906,3.146 6.344,3.313 0.438,0.167 10 false CANH 5.677,3.156 5.906,3.323 0.229,0.167 10 false 11 5.031,3.094 5.146,3.26 0.115,0.167 10 false V 5,3.813 5.167,3.979 0.167,0.167 10 false W 5.667,3.74 5.917,3.958 0.25,0.219 10 false 12 4.417,3.146 4.677,3.406 0.26,0.26 10 false 8 4.375,3.75 4.625,4.021 0.25,0.271 10 false 19 2.823,4.177 3.021,4.406 0.198,0.229 10 false 4 2.75,4.75 2.979,4.958 0.229,0.208 10 false 15 4.406,1.448 4.646,1.667 0.24,0.219 10 false 3 4.375,2.021 4.635,2.323 0.26,0.302 10 false 14 5.031,1.385 5.177,1.552 0.146,0.167 10 false L 5,2.083 5.146,2.25 0.146,0.167 10 false W 5.667,1.458 5.854,1.625 0.188,0.167 10 false 14 5.656,2.021 5.844,2.188 0.188,0.167 10 false 15 5.104,2.271 5.417,2.479 0.313,0.208 10 false G79 5.427,2.292 7.115,2.698 1.688,0.406 10 false Smart Key ECU Assembly (Certification ECU) 5.219,4.01 5.51,4.188 0.292,0.177 10 false G34 5.531,4.01 7.115,4.385 1.583,0.375 10 false Air Conditioning Amplifier Assembly 0.5,5.104 2.073,5.458 1.573,0.354 10 false Airbag Sensor Assembly 1.063,4.75 1.469,4.917 0.406,0.167 10 false CANL 1.073,4.219 1.51,4.385 0.438,0.167 10 false CANH 2.146,4.125 2.344,4.375 0.198,0.25 10 false B 2.146,4.823 2.344,5.021 0.198,0.198 10 false W 0.167,5.104 0.469,5.281 0.302,0.177 10 false G18 1.542,4.208 1.833,4.438 0.292,0.229 10 false 13 1.552,4.729 1.74,4.896 0.188,0.167 10 false 22 4.427,6.927 4.792,7.208 0.365,0.281 10 false G72 3.042,1.417 3.333,1.656 0.292,0.24 10 false 18 4.104,1.406 4.375,1.604 0.271,0.198 10 false 7 3.073,7.625 3.375,7.896 0.302,0.271 10 false 21 4.104,7.615 4.49,7.917 0.385,0.302 10 false 10 2.802,2.448 3.01,2.615 0.208,0.167 10 false 1 2.75,3.021 3,3.26 0.25,0.24 10 false 12 1.063,3.031 1.469,3.198 0.406,0.167 10 false CANL 2.135,3.115 2.292,3.281 0.156,0.167 10 false W 0.083,3.313 0.448,3.479 0.365,0.167 10 false G30 1.052,2.49 1.49,2.656 0.438,0.167 10 false CANH 1.552,2.479 1.771,2.677 0.219,0.198 10 false 4 1.552,3.031 1.792,3.24 0.24,0.208 10 false 3 2.156,2.396 2.333,2.542 0.177,0.146 10 false P 0.417,3.323 2.583,3.771 2.167,0.448 10 false Spiral Cable with Sensor Sub-assembly (Steering Sensor) 5.927,5.479 6.333,5.646 0.406,0.167 10 false CANL 5.021,5.563 5.177,5.729 0.156,0.167 10 false W 5.146,5.75 5.479,5.958 0.333,0.208 10 false G59 5.927,4.906 6.365,5.073 0.438,0.167 10 false CANH 5.656,4.896 5.865,5.063 0.208,0.167 10 false 14 5.667,5.469 5.875,5.635 0.208,0.167 10 false 13 5,4.833 5.292,5.115 0.292,0.281 10 false BE 5.479,5.75 7.135,6.292 1.656,0.542 10 false Main Body ECU (Multiplex Network Body ECU) 0.365,6.917 1.698,7.281 1.333,0.365 10 false Power Steering ECU Assembly 1.063,6.635 1.469,6.802 0.406,0.167 10 false CANL 1.052,6.083 1.49,6.25 0.438,0.167 10 false CANH 1.573,6.083 1.76,6.25 0.188,0.167 10 false 7 2.125,6.708 2.385,6.948 0.26,0.24 10 false W 2.104,6.021 2.396,6.188 0.292,0.167 10 false LG 1.563,6.635 1.75,6.802 0.188,0.167 10 false 8 0.094,6.896 0.354,7.198 0.26,0.302 10 false G6 2.823,6.094 3.01,6.26 0.188,0.167 10 false 6 2.76,6.646 2.948,6.813 0.188,0.167 10 false 17 4.417,4.885 4.625,5.052 0.208,0.167 10 false 9 4.406,5.479 4.615,5.646 0.208,0.167 10 false 20

C349995E03
3.979,6 5.708,6.188 1.729,0.188 10 false : CAN Branch Line (CANH) 3.979,6.406 5.708,6.594 1.729,0.188 10 false : CAN Branch Line (CANL) 0.76,5.99 2.677,6.177 1.917,0.188 10 false : CAN Main Bus Line (CANH) 0.76,6.396 2.677,6.583 1.917,0.188 10 false : CAN Main Bus Line (CANL) 1.792,3.583 1.979,3.844 0.188,0.26 10 false W 0.792,1.865 1.198,2.031 0.406,0.167 10 false CA1L 0.781,1.302 1.219,1.469 0.438,0.167 10 false CA1H 0.573,3.333 0.979,3.5 0.406,0.167 10 false CANL 0.719,3.01 1.156,3.177 0.438,0.167 10 false CANH 1.281,1.854 1.49,2.021 0.208,0.167 10 false 24 2.51,2.844 2.781,3.063 0.271,0.219 10 false 3 2.448,3.583 2.833,3.865 0.385,0.281 10 false 14 1.292,1.302 1.469,1.469 0.177,0.167 10 false 25 1.083,3.5 1.281,3.667 0.198,0.167 10 false 14 1.26,2.917 1.438,3.083 0.177,0.167 10 false 6 4.823,0.229 6.031,0.417 1.208,0.188 10 false x: Suspected Area 0.073,2.125 0.417,2.323 0.344,0.198 10 false G81 0.385,2.135 2.135,2.563 1.75,0.427 10 false Hybrid Vehicle Control Computer Assembly 0.344,3.583 0.667,3.771 0.323,0.188 10 false G4 0.604,3.583 1,3.771 0.396,0.188 10 false DLC3 1.75,2.865 2.115,3.125 0.365,0.26 10 false GR 4.271,1.927 4.5,2.219 0.229,0.292 10 false 10 4.281,2.688 4.49,2.854 0.208,0.167 10 false 21 5.146,2.677 5.333,2.938 0.188,0.26 10 false W 5.167,1.948 5.354,2.188 0.188,0.24 10 false B 5.938,2 6.375,2.167 0.438,0.167 10 false CA1H 5.938,2.594 6.344,2.76 0.406,0.167 10 false CA1L 5.698,2.01 5.938,2.25 0.24,0.24 10 false 37 5.708,2.594 5.938,2.823 0.229,0.229 10 false 38 5.458,2.865 7.146,3.385 1.688,0.521 10 false Brake Booster with Master Cylinder Assembly (Skid Control ECU) 5.167,2.865 5.49,3.052 0.323,0.188 10 false A41 2.625,4.844 3.031,5.01 0.406,0.167 10 false CANL 3.896,4.844 4.333,5.01 0.438,0.167 10 false CANH 2.521,1.177 2.708,1.344 0.188,0.167 10 false 2 2.479,1.948 2.75,2.208 0.271,0.26 10 false 13 3.958,4.333 4.25,4.51 0.292,0.177 10 false L 2.833,4.323 2.979,4.49 0.146,0.167 10 false W 3.917,4.604 4.104,4.771 0.188,0.167 10 false 13 2.854,4.594 3.042,4.76 0.188,0.167 10 false 26 3.281,5.469 3.792,5.656 0.51,0.188 10 false 120 Ω 4.917,5.208 5.302,5.406 0.385,0.198 10 false ECM 4.594,5.208 4.979,5.406 0.385,0.198 10 false A40 3.948,0.375 4.281,0.583 0.333,0.208 10 false SB 2.771,0.375 2.969,0.542 0.198,0.167 10 false W 2.656,0.813 2.906,1.063 0.25,0.25 10 false 15 4.104,0.781 4.271,0.99 0.167,0.208 10 false 4 2.938,0.823 3.25,1.042 0.313,0.219 10 false G86 3.698,0.823 4.01,1.042 0.313,0.219 10 false G86 4.24,2.146 4.552,2.365 0.313,0.219 10 false A74 4.24,2.5 4.552,2.719 0.313,0.219 10 false A74 2.938,3.917 3.25,4.135 0.313,0.219 10 false A74 3.708,3.927 4.021,4.146 0.313,0.219 10 false A74 4.073,3.917 4.26,4.083 0.188,0.167 10 false 9 2.667,3.917 2.938,4.146 0.271,0.229 10 false 20 2.406,3.031 2.719,3.25 0.313,0.219 10 false G86 2.406,3.396 2.719,3.615 0.313,0.219 10 false G86 1.76,1.917 1.917,2.083 0.156,0.167 10 false W 1.729,1.229 1.979,1.417 0.25,0.188 10 false BE 2.427,1.417 2.74,1.635 0.313,0.219 10 false G86 2.427,1.781 2.74,2 0.313,0.219 10 false G86 4.281,1.094 6.271,1.344 1.99,0.25 10 false CAN Junction Connector LH

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the cruise control system on using the cruise control main switch (ON/OFF switch), wait at least 60 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN J/C RH)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U183631E02
2.521,3.74 2.521,4.073 false 2.24,1.729 2.24,1.969 2.24,1.969 2.573,1.969 false 1.167,1.563 0.823,1.563 false 1.177,1.708 0.833,1.708 false 1.427,1.531 1.427,1.167 1.427,1.167 0.813,1.167 false 1.552,1.552 1.552,1.031 1.552,1.031 0.833,1.031 false 1.885,1.542 1.885,0.729 1.885,0.729 2.552,0.729 false 2.01,1.542 2.01,0.948 2.01,0.948 2.552,0.948 false 2.24,1.542 2.24,1.333 2.24,1.333 2.552,1.333 false 2.125,1.542 2.125,1.146 2.125,1.146 2.552,1.146 false 1.438,1.719 1.438,1.948 1.438,1.948 0.844,1.948 false 1.552,1.719 1.552,2.135 1.552,2.135 0.854,2.135 false 1.896,1.719 1.896,2.573 1.896,2.573 2.573,2.573 false 2.01,1.719 2.01,2.344 2.01,2.344 2.573,2.344 false 2.125,1.719 2.125,2.167 2.125,2.167 2.563,2.167 false 1.781,1.427 1.781,0.458 1.781,0.458 0.854,0.458 false 1.781,1.708 1.781,2.313 1.781,2.313 0.854,2.313 false 1.625,0.094 1.979,0.323 0.354,0.229 10 false G72 0.25,3.406 0.604,3.635 0.354,0.229 10 false G4 0.094,0.042 0.604,0.375 0.51,0.333 10 false *a 2.375,4.104 2.729,4.313 0.354,0.208 10 false BAT 0.271,1.458 0.979,1.677 0.708,0.219 10 false CANH*b 0.281,1.646 0.99,1.865 0.708,0.219 10 false CANL*b 0.125,2.781 0.635,3.115 0.51,0.333 10 false *1 0.25,1.083 0.958,1.302 0.708,0.219 10 false CANH*c 0.302,0.385 1.01,0.604 0.708,0.219 10 false CANH*e 0.25,0.917 0.958,1.135 0.708,0.219 10 false CANH*d 2.594,0.646 3.219,0.865 0.625,0.219 10 false CANH*f 2.594,0.865 3.219,1.083 0.625,0.219 10 false CANH*g 2.594,1.063 3.208,1.281 0.615,0.219 10 false CANH*h 2.583,1.26 3.167,1.479 0.583,0.219 10 false CANH*i 0.292,1.854 1,2.073 0.708,0.219 10 false CANL*c 0.292,2.042 1,2.26 0.708,0.219 10 false CANL*d 2.604,2.49 3.198,2.708 0.594,0.219 10 false CANL*f 2.604,2.271 3.198,2.49 0.594,0.219 10 false CANL*g 2.604,2.083 3.177,2.302 0.573,0.219 10 false CANL*h 2.604,1.885 3.219,2.104 0.615,0.219 10 false CANL*i 0.302,2.24 1.01,2.458 0.708,0.219 10 false CANL*e

Disconnect the G72 CAN junction connector RH.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
G72-1 (CANH) - G4-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Spiral cable with sensor sub-assembly (Steering sensor)
G72-12 (CANL) - G4-16 (BAT)
G72-3 (CANH) - G4-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Smart key ECU assembly (Certification ECU)
G72-14 (CANL) - G4-16 (BAT)
G72-4 (CANH) - G4-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Airbag sensor assembly
G72-15 (CANL) - G4-16 (BAT)
G72-6 (CANH) - G4-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Power steering ECU assembly
G72-17 (CANL) - G4-16 (BAT)
G72-7 (CANH) - G4-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Combination meter assembly
G72-18 (CANL) - G4-16 (BAT)
G72-8 (CANH) - G4-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Air conditioning amplifier assembly
G72-19 (CANL) - G4-16 (BAT)
G72-9 (CANH) - G4-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Main body ECU (Multiplex network body ECU)
G72-20 (CANL) - G4-16 (BAT)
G72-10 (CANH) - G4-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher CAN junction connector LH
G72-21 (CANL) - G4-16 (BAT)


Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to CAN Junction Connector RH)
*b to Spiral Cable with Sensor Sub-assembly (Steering Sensor)
*c to Smart Key ECU Assembly (Certification ECU)
*d to Airbag Sensor Assembly
*e to Power Steering ECU Assembly
*f to Combination Meter Assembly
*g to Air Conditioning Amplifier Assembly
*h to Main Body ECU (Multiplex Network Body ECU)
*i to CAN Junction Connector LH


Result:
Result Proceed to
OK A
NG (CAN junction connector LH main line) B
NG (ECU or sensor bus line) C



A

REPLACE CAN JUNCTION CONNECTOR RH

B

2.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN J/C LH (INSTRUMENT PANEL WIRE SIDE))

C

4.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU, SENSOR)
2.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN J/C LH (INSTRUMENT PANEL WIRE SIDE))
a.
U183632E02
2.51,3.719 2.51,4.052 false 1.313,1.542 1.313,1.125 1.313,1.125 0.823,1.125 false 1.427,1.542 1.427,0.75 1.427,0.75 0.833,0.75 false 1.542,1.531 1.542,0.719 1.542,0.719 2.552,0.719 false 1.313,1.729 1.313,2.063 1.313,2.063 0.844,2.063 false 1.438,1.729 1.438,2.302 1.438,2.302 0.854,2.302 false 1.552,1.74 1.552,2.354 1.552,2.354 2.448,2.354 false 1.615,0.188 1.969,0.417 0.354,0.229 10 false G86 0.24,3.406 0.594,3.635 0.354,0.229 10 false G4 0.063,0.042 0.573,0.375 0.51,0.333 10 false *a 2.344,4.083 2.698,4.292 0.354,0.208 10 false BAT 0.052,2.573 0.563,2.906 0.51,0.333 10 false *1 0.219,1.042 0.927,1.26 0.708,0.219 10 false CANH*b 0.208,0.635 0.917,0.854 0.708,0.219 10 false CANH*c 2.594,0.625 3.302,0.844 0.708,0.219 10 false CANH*d 0.281,1.979 0.99,2.198 0.708,0.219 10 false CANL*b 0.292,2.219 1,2.438 0.708,0.219 10 false CANL*c 2.5,2.26 3.208,2.479 0.708,0.219 10 false CANL*d

Disconnect the G86 CAN junction connector LH (instrument panel wire side).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
G86-2 (CANH) - G4-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Hybrid vehicle control computer assembly
G86-13 (CANL) - G4-16 (BAT)
G86-3 (CANH) - G4-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher DLC3
G86-14 (CANL) - G4-16 (BAT)
G86-4 (CANH) - G4-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher CAN junction connector RH
G86-15 (CANL) - G4-16 (BAT)



Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to CAN Junction Connector LH (Instrument Panel Wire Side))
*b to Hybrid Vehicle Control Computer Assembly
*c to DLC3
*d to CAN Junction Connector RH

Result:
Result Proceed to
OK A
NG (CAN junction connector RH main line) B
NG (ECU or sensor bus line) C
NG (DLC3 branch line) D



A

3.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN J/C LH (ENGINE ROOM MAIN WIRE SIDE))

B

REPAIR OR REPLACE CAN MAIN BUS LINE (CAN J/C LH (INSTRUMENT PANEL WIRE SIDE) - CAN J/C RH)

C

4.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU, SENSOR)

D

REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3

3.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN J/C LH (ENGINE ROOM MAIN WIRE SIDE))
a.
U183633E02
2.51,3.74 2.51,4.073 false 2.104,1.552 2.104,0.74 2.104,0.74 2.542,0.74 false 2.229,1.542 2.229,0.948 2.229,0.948 2.542,0.948 false 2.115,1.729 2.115,2.396 2.115,2.396 2.573,2.396 false 2.229,1.729 2.229,2.146 2.229,2.146 2.563,2.146 false 1.615,0.188 1.969,0.417 0.354,0.229 10 false A74 0.24,3.417 0.594,3.646 0.354,0.229 10 false G4 0.052,0 0.563,0.333 0.51,0.333 10 false *a 2.344,4.104 2.698,4.313 0.354,0.208 10 false BAT 2.604,0.635 3.313,0.854 0.708,0.219 10 false CANH*b 2.604,2.313 3.313,2.531 0.708,0.219 10 false CANL*b 0.052,2.573 0.563,2.906 0.51,0.333 10 false *1 2.604,0.875 3.313,1.094 0.708,0.219 10 false CANH*c 2.604,2.063 3.313,2.281 0.708,0.219 10 false CANL*c

Disconnect the A74 CAN junction connector LH (engine room main wire side).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A74-9 (CANH) - G4-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher ECM
A74-20 (CANL) - G4-16 (BAT)
A74-10 (CANH) - G4-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Brake booster with master cylinder assembly (Skid control ECU)
A74-21 (CANL) - G4-16 (BAT)



Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to CAN Junction Connector LH (Engine Room Main Wire Side))
*b to ECM
*c to Brake Booster with Master Cylinder Assembly (Skid Control ECU)

Result:
Result Proceed to
OK A
NG (ECU or sensor bus line) B



A

REPLACE CAN JUNCTION CONNECTOR LH

B

4.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU, SENSOR)
4.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU, SENSOR)
a.

Reconnect all wire harness connectors (CAN junction connector LH and CAN junction connector RH).


b.

Disconnect the ECU or sensor connected to the CAN bus line that is shorted to +B.

HINT:

If the ECU or sensor has multiple connectors, disconnect the connector that includes the CAN bus lines. To determine the ECU or sensor that is connected to the shorted bus line, refer to the terminals of ECU tables (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU).



c.
U183503E01
2.314,0.165 2.733,0.316 0.420,0.151 10 CANH 1.087,1.901 1.498,2.043 0.411,0.142 10 CANL 0.159,0.165 0.324,0.309 0.165,0.144 10 *1 1.957,0.903 2.266,0.256 false 1.962,1.486 1.585,1.981 false 1.636,0.205 1.982,0.364 0.345,0.159 10 G4 2.324,1.486 2.72,1.86 false 2.795,1.78 3.205,1.922 0.411,0.142 10 BAT

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G4-6 (CANH) - G4-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G4-14 (CANL) - G4-16 (BAT)


Text in Illustration
*1 DLC3

HINT:

If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.




OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BUS LINE OR CONNECTOR