Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2011.12–2014.12
RM2170E _57 Power Source / Network _057033 NETWORKING _0278068 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Combination Meter ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Combination Meter ECU Communication Stop Mode Either condition is met:
·

"Combination Meter" is not displayed on the "Communication Bus Check" screen of the intelligent tester (See page (Click here))

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Combination Meter ECU Communication Stop Mode" in "DTC Combination Table" (See page (Click here))


·

Combination meter assembly main line or connector

·

Power source circuit of combination meter assembly

·

Combination meter assembly ground circuit

·

Combination meter assembly



WIRING DIAGRAM

C252851E11
5.896,2.458 5.667,2.458 5.667,2.458 5.333,3.052 false 3.646,4.552 3.646,5.083 3.646,5.083 3.896,5.083 false 1.375,5.021 2.198,5.219 0.823,0.198 10 false Trouble Area 4.833,2.313 5.229,2.469 0.396,0.156 10 false DLC3 1.25,0.594 3.75,0.927 2.5,0.333 10 false : CAN Main Bus Line (CANH) 1.25,0.938 3.75,1.271 2.5,0.333 10 false : CAN Main Bus Line (CANL) 1.24,1.271 2.979,1.604 1.74,0.333 10 false : CAN Branch Line (CANH) 1.24,1.625 2.979,1.958 1.74,0.333 10 false : CAN Branch Line (CANL) 1.229,4.583 3.104,4.76 1.875,0.177 10 false Combination Meter Assembly 1.688,3.125 1.813,3.281 0.125,0.156 10 false B 1.688,3.688 1.948,3.833 0.26,0.146 10 false IG+ 1.688,4.271 1.885,4.427 0.198,0.156 10 false ET 1.229,4.427 1.438,4.573 0.208,0.146 10 false G1 2.406,3.729 2.792,3.885 0.385,0.156 10 false CANL 2.385,3.094 2.792,3.25 0.406,0.156 10 false CANH 2.125,3.969 2.521,4.115 0.396,0.146 10 false 120 Ω 6.167,3.958 6.563,4.115 0.396,0.156 10 false 120 Ω 1.479,4.188 1.656,4.333 0.177,0.146 10 false 20 2.854,3.094 3.021,3.24 0.167,0.146 10 false 31 2.844,3.729 3.021,3.885 0.177,0.156 10 false 32 0.708,3.26 1.563,3.417 0.854,0.156 10 false ECU-B NO. 2 0.875,3.802 1.406,3.948 0.531,0.146 10 false METER 1.552,3.01 1.646,3.156 0.094,0.146 10 false 1 1.479,3.563 1.656,3.708 0.177,0.146 10 false 21 5.948,2.365 6.844,3.01 0.896,0.646 10 false CAN Junction Connector LH 3.938,4.99 5.833,5.24 1.896,0.25 10 false CAN Junction Connector RH 6.333,4.583 6.698,4.729 0.365,0.146 10 false ECM 0.104,0.063 1.406,0.313 1.302,0.25 12 false V Bus (for LHD): 6.031,4.583 6.344,4.74 0.313,0.156 10 false A40

C244007E23
5.792,2.333 5.615,2.333 5.615,2.333 5.323,3.052 false 3.646,4.552 3.646,5.063 3.646,5.063 3.906,5.063 false 1.375,5.021 2.198,5.219 0.823,0.198 10 false Trouble Area 3.635,2.323 4.354,2.635 0.719,0.313 10 false DLC3 1.24,0.594 3.74,0.927 2.5,0.333 10 false : CAN Main Bus Line (CANH) 1.24,0.938 3.74,1.271 2.5,0.333 10 false : CAN Main Bus Line (CANL) 1.24,1.281 2.979,1.615 1.74,0.333 10 false : CAN Branch Line (CANH) 1.24,1.615 2.979,1.948 1.74,0.333 10 false : CAN Branch Line (CANL) 1.313,4.594 3.188,4.771 1.875,0.177 10 false Combination Meter Assembly 1.688,3.104 2.146,3.417 0.458,0.313 10 false B 1.688,3.656 1.948,3.802 0.26,0.146 10 false IG+ 1.688,4.271 2.208,4.563 0.521,0.292 10 false ET 1.313,4.438 1.75,4.625 0.438,0.188 10 false G1 2.406,3.729 2.979,3.938 0.573,0.208 10 false CANL 2.385,3.094 3.344,3.469 0.958,0.375 10 false CANH 2.156,3.969 2.771,4.188 0.615,0.219 10 false 120 Ω 6.167,3.958 6.563,4.115 0.396,0.156 10 false 120 Ω 1.479,4.177 1.813,4.344 0.333,0.167 10 false 20 2.844,3.094 3.156,3.302 0.313,0.208 10 false 31 2.844,3.729 3.135,3.979 0.292,0.25 10 false 32 0.708,3.25 1.76,3.469 1.052,0.219 10 false ECU-B NO. 2 0.906,3.802 1.604,4.042 0.698,0.24 10 false METER 1.521,3.01 2.292,3.479 0.771,0.469 10 false 1 1.479,3.563 1.865,3.771 0.385,0.208 10 false 21 5.865,2.25 6.781,2.677 0.917,0.427 10 false CAN Junction Connector LH 3.969,4.969 5.969,5.25 2,0.281 10 false CAN Junction Connector RH 6.344,4.583 6.823,4.844 0.479,0.26 10 false ECM 0.094,0.063 1.385,0.333 1.292,0.271 12 false V Bus (for RHD): 6.021,4.583 6.594,4.844 0.573,0.26 10 false A40

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the cruise control system on using the cruise control main switch (ON/OFF switch), wait at least 60 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more.

·

After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (COMBINATION METER ASSEMBLY MAIN LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U159536E01
1.619,0.754 1.825,0.907 0.206,0.153 10 G1 0.097,0.075 0.255,0.227 0.158,0.152 10 *a 0.975,2.91 1.403,3.062 0.429,0.152 10 CANH 2.25,2.904 2.679,3.056 0.429,0.152 10 CANL 1.801,2.634 1.698,2.992 1.698,2.992 1.497,2.992 false 1.914,2.634 2.031,2.992 2.031,2.992 2.231,2.992 false

Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G1-31 (CANH) - G1-32 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (COMBINATION METER ASSEMBLY MAIN LINE)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
U159537E01
1.619,0.773 1.825,0.926 0.206,0.153 10 G1 0.097,0.094 0.255,0.246 0.158,0.152 10 *a 3.081,1.62 3.292,1.772 0.211,0.152 10 ET 2.839,2.385 2.839,1.701 2.839,1.701 3.059,1.701 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G1-20 (ET) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)


b.
U159538E01
1.619,0.754 1.825,0.907 0.206,0.153 10 G1 0.097,0.075 0.255,0.227 0.158,0.152 10 *a 0.223,1.599 0.333,1.750 0.110,0.152 10 B 0.939,2.939 1.195,3.091 0.256,0.152 10 IG+ 0.642,2.366 0.515,1.682 0.515,1.682 0.353,1.682 false 0.642,2.637 0.763,3.02 0.763,3.02 0.913,3.02 false

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G1-21 (IG+) - Body ground Power switch on (IG) 11 to 14 V
G1-1 (B) - Body ground Power switch off 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)


OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)