Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › from 2014.12
RM2170E _57 Power Source / Network _057033 NETWORKING _0278069 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2785  Communication Malfunction between ECUs Connected by LIN  


DESCRIPTION

The certification ECU (smart key ECU assembly) monitors communication between all the ECUs connected to the certification bus lines. When the certification ECU (smart key ECU assembly) detects errors in communication with all the ECUs connected to the certification bus lines at a set interval and 3 times in a row, DTC B2785 will be stored.

DTC No. DTC Detection Condition Trouble Area
B2785
·

Errors in LIN communication between ECUs or an open or short in communication lines

·

LIN communication from the certification ECU (smart key ECU assembly) detects errors in communication 3 times in a row.


·

Certification ECU (smart key ECU assembly)

·

Steering lock ECU (steering lock actuator assembly)

·

ID code box (immobiliser code ECU)

·

Wire harness or connector



WIRING DIAGRAM

B389343E07
4.619,3.743 6.426,4.050 1.807,0.308 10 Steering Lock ECU (Steering Lock Actuator Assembly) 1.38,1.921 2.989,2.242 1.608,0.322 10 ID Code Box (Immobiliser Code ECU) 1.38,1.744 1.736,1.898 0.356,0.153 10 G49 4.611,1.718 4.967,1.871 0.356,0.153 10 G79 4.611,3.576 4.967,3.730 0.356,0.153 10 G50 4.34,0.988 4.621,1.142 0.282,0.153 10 17 4.613,1.886 6.179,2.217 1.566,0.331 10 Certification ECU (Smart Key ECU Assembly) 0.912,4.308 2.533,4.457 1.621,0.149 10 : LIN Communication Line 4.634,1.142 4.915,1.296 0.282,0.153 10 LIN 4.648,3.02 4.929,3.173 0.282,0.153 10 LIN 4.424,2.88 4.705,3.033 0.282,0.153 10 5 2.546,1.142 2.944,1.296 0.398,0.153 10 LIN1 2.981,0.988 3.262,1.142 0.282,0.153 10 2

CAUTION / NOTICE / HINT

NOTICE:
·

If the certification ECU (smart key ECU assembly), ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator assembly) is replaced, refer to Service Bulletin.

·

When using the intelligent tester to troubleshoot with the power switch off:

Connect the intelligent tester to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - EACH ECU)
a.

Disconnect the G79, G49 and G50 connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G79-17 (LIN) - G50-5 (LIN) Always Below 1 Ω
G79-17 (LIN) - G49-2 (LIN1) Always Below 1 Ω
G79-17 (LIN) - Body ground Always 10 kΩ or higher




OK

2.CHECK DTC OUTPUT (STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK DTC OUTPUT (STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY))
a.

Reconnect the G79 and G49 connectors.



c.

Recheck for DTCs.

Result:
Result Proceed to
DTC B2785 is output A
DTC B2785 is not output B




A

3.CHECK DTC OUTPUT (ID CODE BOX (IMMOBILISER CODE ECU))

B

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

3.CHECK DTC OUTPUT (ID CODE BOX (IMMOBILISER CODE ECU))
a.

Reconnect the G50 connector.


b.

Disconnect the G49 connector.



d.

Recheck for DTCs.

Result:
Result Proceed to
DTC B2785 is output A
DTC B2785 is not output B




A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)