Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY › from 2014.12
RM2170E _55 Steering _057027 STEERING COLUMN _0278050 STEERING COLUMN ASSEMBLY A

STEERING COLUMN  STEERING COLUMN ASSEMBLY  REMOVAL  


PROCEDURE

Hide 2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 45130 3.REMOVE HORN BUTTON ASSEMBLY

Hide 45100 4.REMOVE STEERING WHEEL ASSEMBLY

Hide 45287 5.REMOVE LOWER STEERING COLUMN COVER

a.
C248042

Remove the 3 screws.


b.
C256915

Disengage the 4 claws and remove the lower steering column cover.


Hide 45286B 6.REMOVE UPPER STEERING COLUMN COVER

a.
C248044

Disengage the 2 claws and remove the upper steering column cover.


Hide 7.REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
·

Do not replace the spiral cable with sensor sub-assembly with the negative (-) auxiliary battery cable connected and the power switch on (IG).

·

Do not rotate the spiral cable with sensor sub-assembly without the steering wheel with the negative (-) auxiliary battery cable connected and the power switch on (IG).

·

Ensure that the steering wheel is installed and aligned straight when inspecting the steering sensor.

·

Do not remove the spiral cable from the steering sensor.



a.

Disconnect the connectors from the turn signal switch assembly with spiral cable sub-assembly.


b.
C248045E02
1.271,0.323 1.479,0.323 1.479,0.323 1.479,0.563 true 0.635,0.833 0.531,0.833 false 1.406,0.583 1.573,0.74 0.167,0.156 10 false *1 0.333,0.76 0.5,0.927 0.167,0.167 10 false *2

Using pliers, expand the clamp.

Text in Illustration
*1 Clamp
*2 Claw


c.

While holding the clamp expanded, raise the claw using a screwdriver to disengage it, and then remove the turn signal switch assembly with spiral cable sub-assembly from the steering column assembly.


Hide 73900 8.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIR BAG ASSEMBLY

Hide 45259A 9.REMOVE COLUMN HOLE COVER SILENCER SHEET

a.
C248046

Remove the 2 clips and the column hole cover silencer sheet.


Hide 45209 10.SEPARATE STEERING SLIDING YOKE SUB-ASSEMBLY

a.
C249572E04
1.448,1.594 0.677,1.594 true 1.417,1.688 0.917,1.688 0.917,1.688 0.917,1.594 true 0.469,1.521 0.646,1.667 0.177,0.146 10 false *a 2.135,0.677 2.26,0.823 0.125,0.146 10 false A 1.948,1.542 2.073,1.698 0.125,0.156 10 false B

Put matchmarks on the steering sliding yoke sub-assembly and steering gear assembly.

Text in Illustration
*a Matchmark


b.

Loosen bolt A.


c.

Remove bolt B.


d.

Separate the steering sliding yoke sub-assembly from the steering gear assembly.


Hide 45209 11.REMOVE STEERING SLIDING YOKE SUB-ASSEMBLY

a.
C232525E01
2.519,0.661 2.687,0.815 0.168,0.154 10 *a 1.933,0.747 2.494,0.747 2.494,0.747 1.893,0.894 false

Put matchmarks on the steering sliding yoke sub-assembly and No. 2 steering intermediate shaft assembly.

Text in Illustration
*a Matchmark


b.

Remove the steering sliding yoke sub-assembly from the No. 2 steering intermediate shaft assembly.


Hide 45260 12.REMOVE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C252587E02
1.813,1.333 1.813,1.865 true 1.688,1.313 1.688,1.635 1.688,1.635 1.813,1.635 true 1.729,1.865 1.979,2.073 0.25,0.208 10 false *a

Put matchmarks on the No. 2 steering intermediate shaft assembly and steering column assembly.

Text in Illustration
*a Matchmark


b.

Remove the bolt.


c.

Remove the steering intermediate shaft assembly from the steering column assembly.


Hide 13.REMOVE BRAKE PEDAL SUPPORT ASSEMBLY

Hide 14.REMOVE UPPER INSTRUMENT PANEL ASSEMBLY

Hide 15.REMOVE STEERING COLUMN ASSEMBLY

a.
C248047

Disconnect the 2 connectors from the power steering ECU assembly.


b.

Disengage the wire harness clamp.


c.

Disconnect the connectors and disengage the wire harness clamps from the steering column assembly.


d.
C252588

Remove the bolt, 2 nuts and steering column assembly.