Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2011.12–2013.12
RM2170E _57 Power Source / Network _057033 NETWORKING _0278069 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2287  LIN Communication Master Malfunction  


DESCRIPTION

This DTC is stored when there is an open, short or ECU communication malfunction between the power management control ECU and certification ECU (smart key ECU assembly).

DTC No. DTC Detection Condition Trouble Area
B2287 There is an open, short or ECU communication malfunction between power management control ECU and certification ECU (smart key ECU assembly).
·

Power management control ECU

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector



WIRING DIAGRAM

B228566E13
0.701,3.469 2.329,3.625 1.628,0.156 10 : LIN Communication Line 0.89,2.509 2.448,2.825 1.559,0.316 10 Certification ECU (Smart Key ECU Assembly) 4.049,2.509 5.344,2.825 1.295,0.316 10 Power Management Control ECU 0.89,2.341 1.249,2.490 0.360,0.149 10 G54 1.849,1.465 2.102,1.628 0.253,0.163 10 LIN 4.231,1.465 4.568,1.628 0.336,0.163 10 LIN2 4.745,1.064 5.128,1.226 0.383,0.163 10 AM22 4.745,1.447 5.128,1.609 0.383,0.163 10 AM21 4.932,1.979 5.129,2.142 0.198,0.163 10 E1 2.155,1.332 2.334,1.474 0.179,0.142 10 12 3.891,1.475 4.186,1.623 0.295,0.149 10 G58 5.185,1.071 5.475,1.220 0.290,0.149 10 G57 5.185,1.456 5.475,1.605 0.290,0.149 10 G58 5.185,1.993 5.494,2.142 0.309,0.149 10 G57 3.954,1.297 4.152,1.446 0.198,0.149 10 11 5.285,0.895 5.386,1.044 0.100,0.149 10 1 5.285,1.283 5.386,1.432 0.100,0.149 10 7 5.285,1.825 5.386,1.974 0.100,0.149 10 6 6.02,1.218 6.333,1.381 0.313,0.163 10 AM2 4.591,0.391 5.946,0.554 1.355,0.163 10 from Auxiliary Battery

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

If the certification ECU (smart key ECU assembly) or power management control ECU is replaced, refer to Service Bulletin.

·

When using the intelligent tester to troubleshoot with the power switch off:

Connect the intelligent tester to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.



PROCEDURE

1.CHECK DTC OUTPUT

b.

Recheck for DTCs.

HINT:

Check for both "Entry&Start" and "Power Source Control" DTCs.


Result:
Result Proceed to
Only DTC B2287 is output. A
DTC B2287 and B2785 are output simultaneously. B


HINT:

When DTC B2287 and B2785 are output simultaneously, perform troubleshooting for DTC B2785 first.




A

2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - AUXILIARY BATTERY AND BODY GROUND)

B

2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - AUXILIARY BATTERY AND BODY GROUND)
a.

Disconnect the G57 and G58 power management control ECU connectors.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G57-6 (E1) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
G57-1 (AM22) - Body ground Power switch off 11 to 14 V
G58-7 (AM21) - Body ground Power switch off 11 to 14 V




OK

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - POWER MANAGEMENT CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - POWER MANAGEMENT CONTROL ECU)
a.

Disconnect the G54 certification ECU (smart key ECU assembly) connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G58-11 (LIN2) - G54-12 (LIN) Always Below 1 Ω
G58-11 (LIN2) - Body ground Always 10 kΩ or higher




OK

4.CHECK SMART ENTRY AND START SYSTEM (for Entry Function)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK SMART ENTRY AND START SYSTEM (for Entry Function)
a.

Check that the entry lock and unlock function operates normally (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

OK:

Entry lock and unlock function operates normally.




OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)