Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › from 2014.12
RM2170E _57 Power Source / Network _057033 NETWORKING _0278069 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2789  No Response from ID BOX  


DESCRIPTION

This DTC is stored when LIN communication between the certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) stops for 10 seconds or more.

DTC No. DTC Detection Condition Trouble Area
B2789 No communication between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) for 10 seconds or more.
·

ID code box (immobiliser code ECU)

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector



WIRING DIAGRAM

B445874E04
4.292,0.406 5.792,0.76 1.5,0.354 10 false from Auxiliary Battery 5.156,0.948 5.563,1.24 0.406,0.292 10 false 1 5.458,1.229 6.427,1.625 0.969,0.396 10 false ECU-B NO. 2 4.875,1.073 5.281,1.365 0.406,0.292 10 false +B 4.771,2 5.177,2.292 0.406,0.292 10 false GND 5.167,1.885 5.573,2.177 0.406,0.292 10 false 5 4.229,1.469 4.635,1.76 0.406,0.292 10 false LIN1 4.042,1.323 4.448,1.615 0.406,0.292 10 false 2 2.146,1.323 2.552,1.615 0.406,0.292 10 false 17 0.813,2.365 1.219,2.656 0.406,0.292 10 false G79 0.802,2.531 2.333,3.073 1.531,0.542 10 false Certification ECU (Smart Key ECU Assembly) 0.667,3.469 2.698,3.698 2.031,0.229 10 false : LIN Communication Line 3.938,2.375 4.344,2.667 0.406,0.292 10 false G49 3.927,2.542 5.406,3.104 1.479,0.563 10 false ID Code Box (Immobiliser Code ECU) 1.844,1.469 2.25,1.76 0.406,0.292 10 false LIN

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

If the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is replaced, refer to Service Bulletin.

·

When using the intelligent tester to troubleshoot with the power switch off:

Connect the intelligent tester to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.



PROCEDURE

1.CHECK DTC OUTPUT

b.

Recheck for DTCs.

Result:
Result Proceed to
Only B2789 is output A
DTC B2789 and B2785 are output simultaneously B


HINT:

When DTC B2789 and B2785 are output simultaneously, perform troubleshooting for DTC B2785 first.




A

2.CHECK HARNESS AND CONNECTOR (ID CODE BOX - AUXILIARY BATTERY AND BODY GROUND)

B

2.CHECK HARNESS AND CONNECTOR (ID CODE BOX - AUXILIARY BATTERY AND BODY GROUND)
a.

Disconnect the G49 ID code box (immobiliser code ECU).


b.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G49-5 (GND) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
G49-1 (+B) - Body ground Power switch off 11 to 14 V




OK

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - ID CODE BOX)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - ID CODE BOX)
a.

Disconnect the G79 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G79-17 (LIN) - G49-2 (LIN1) Always Below 1 Ω
G79-17 (LIN) - Body ground Always 10 kΩ or higher




OK

4.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Replace the ID code box (immobiliser code ECU).

HINT:

Refer to Service Bulletin.




NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT

b.

Recheck for DTCs.

OK:

DTC B2789 is not output.




OK

END (ID CODE BOX (IMMOBILISER CODE ECU) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)