Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM2170E _57 Power Source / Network _057033 NETWORKING _0278069 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2325  LIN Communication Bus Malfunction  


DESCRIPTION

The main body ECU (multiplex network body ECU) monitors communication between all the ECUs connected to the door bus lines. When the main body ECU (multiplex network body ECU) detects errors in communication with all the ECUs connected to the door bus lines at 2.6-second intervals and 3 times in a row, DTC B2325 will be stored.

DTC No. DTC Detection Condition Trouble Area
B2325 Main body ECU (multiplex network body ECU) detects errors in communication with the ECUs connected to the door bus lines 3 times in a row.
·

Power window regulator motor assembly (for driver door)

·

Main body ECU (multiplex network body ECU)

·

Instrument panel junction block assembly

·

Wire harness or connector



WIRING DIAGRAM

B274860E22
0.816,2.425 2.454,2.562 1.637,0.137 10 : LIN Communication Line 0.39,1.883 3.064,2.034 2.674,0.151 10 Instrument Panel Junction Block Assembly 0.857,0.994 2.496,1.302 1.640,0.309 10 Main Body ECU (Multiplex Network Body ECU) 1.31,0.524 1.637,0.662 0.327,0.137 10 LIN2 4.7,0.524 4.958,0.662 0.258,0.137 10 LIN 0.39,1.731 0.610,1.878 0.221,0.147 10 3B 4.504,1.893 6.605,2.363 2.101,0.471 10 Power Window Regulator Motor Assembly (for Driver Door) 4.504,1.741 5.188,1.892 0.684,0.151 10 J3*1, H3*2 5.249,1.187 5.596,1.343 0.347,0.156 10 GND 5.457,0.524 5.585,0.680 0.128,0.156 10 B 6.083,0.678 6.669,0.834 0.586,0.156 10 DOOR D 5.646,0.41 5.779,0.575 0.133,0.165 10 2 5.646,1.075 5.779,1.240 0.133,0.165 10 1 4.508,0.389 4.638,0.545 0.130,0.156 10 9 2.627,0.389 2.801,0.531 0.174,0.142 10 12 1.707,0.389 1.881,0.531 0.174,0.142 10 16 0.859,0.844 1.117,0.986 0.258,0.142 10 MB 2.237,0.389 2.564,0.579 0.327,0.191 10 LIN2 3.299,2.021 4.025,2.172 0.725,0.151 10 *1: for LHD 3.299,2.404 4.062,2.555 0.762,0.151 10 *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

When the power window regulator motor assembly (for driver door) is replaced or removed and reinstalled, it requires initialization (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).

·

When using the intelligent tester to troubleshoot with the power switch off:

Connect the intelligent tester to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.



PROCEDURE

1.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

U159216E01
1.926,0.852 2.193,1.029 0.267,0.177 10 MB 5.625,0.579 5.892,0.756 0.267,0.177 10 3B 5.483,2.335 5.835,2.512 0.353,0.177 10 LIN2 6.135,1.691 5.628,2.334 false 1.616,2.251 1.969,2.428 0.353,0.177 10 LIN2 2.027,1.715 1.761,2.25 false 0.287,0.257 0.554,0.434 0.267,0.177 10 *a 4.736,0.257 5.003,0.434 0.267,0.177 10 *b


c.

Measure the resistance according to the value(s) in the table below.

HINT:

This inspection is to check the LIN line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


Standard Resistance:
Tester Connection Condition Specified Condition
3B-12 (LIN2) - MB-16 (LIN2) Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
*b Component without harness connected
(Instrument Panel Junction Block Assembly)


d.

Install the main body ECU (multiplex network body ECU) to the instrument panel junction block assembly.


e.

Install the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION).



OK

2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - EACH ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - EACH ECU)
a.

Disconnect the J3*1 or H3*2 power window regulator motor (for driver door) connector.

*1: for LHD

*2: for RHD



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
3B-12 (LIN2) - J3-9 (LIN) Always Below 1 Ω
J3-9 (LIN) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
3B-12 (LIN2) - H3-9 (LIN) Always Below 1 Ω
J3-9 (LIN) - Body ground Always 10 kΩ or higher




OK

3.CHECK DTC OUTPUT (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for DRIVER DOOR))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK DTC OUTPUT (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for DRIVER DOOR))
a.

Reconnect the 3B instrument panel junction block assembly connector.



c.

After 10 seconds have elapsed, check if the trouble occurs again.


d.

Check for DTCs again.



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for DRIVER DOOR)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)