Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM2170E _57 Power Source / Network _057033 NETWORKING _0278069 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2321  Driver Side Door ECU Communication Stop  


DESCRIPTION

This DTC is stored when LIN communication between the power window regulator motor assembly (for driver door) and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC No. DTC Detection Condition Trouble Area
B2321 No communication between power window regulator motor assembly (for driver door) and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Power window regulator motor assembly (for driver door)

·

Main body ECU (multiplex network body ECU)

·

Wire harness or connector

·

Instrument panel junction block assembly



WIRING DIAGRAM

B274860E22
0.816,2.425 2.454,2.562 1.637,0.137 10 : LIN Communication Line 0.39,1.883 3.064,2.034 2.674,0.151 10 Instrument Panel Junction Block Assembly 0.857,0.994 2.496,1.302 1.640,0.309 10 Main Body ECU (Multiplex Network Body ECU) 1.31,0.524 1.637,0.662 0.327,0.137 10 LIN2 4.7,0.524 4.958,0.662 0.258,0.137 10 LIN 0.39,1.731 0.610,1.878 0.221,0.147 10 3B 4.504,1.893 6.605,2.363 2.101,0.471 10 Power Window Regulator Motor Assembly (for Driver Door) 4.504,1.741 5.188,1.892 0.684,0.151 10 J3*1, H3*2 5.249,1.187 5.596,1.343 0.347,0.156 10 GND 5.457,0.524 5.585,0.680 0.128,0.156 10 B 6.083,0.678 6.669,0.834 0.586,0.156 10 DOOR D 5.646,0.41 5.779,0.575 0.133,0.165 10 2 5.646,1.075 5.779,1.240 0.133,0.165 10 1 4.508,0.389 4.638,0.545 0.130,0.156 10 9 2.627,0.389 2.801,0.531 0.174,0.142 10 12 1.707,0.389 1.881,0.531 0.174,0.142 10 16 0.859,0.844 1.117,0.986 0.258,0.142 10 MB 2.237,0.389 2.564,0.579 0.327,0.191 10 LIN2 3.299,2.021 4.025,2.172 0.725,0.151 10 *1: for LHD 3.299,2.404 4.062,2.555 0.762,0.151 10 *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When the power window regulator motor assembly (for driver door) is replaced or removed and reinstalled, it requires initialization (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).

·

When using the intelligent tester to troubleshoot with the power switch off:

Connect the intelligent tester to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY)
a.

Disconnect the 3B instrument panel junction block assembly connector.


b.

Disconnect the J3*1 or H3*2 power window regulator motor (for driver door) connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
3B-12 (LIN2) - J3-9 (LIN) Always Below 1 Ω
3B-12 (LIN2) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
3B-12 (LIN2) - H3-9 (LIN) Always Below 1 Ω
3B-12 (LIN2) - Body ground Always 10 kΩ or higher




OK

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).

U159216E01
1.926,0.852 2.193,1.029 0.267,0.177 10 MB 5.625,0.579 5.892,0.756 0.267,0.177 10 3B 5.483,2.335 5.835,2.512 0.353,0.177 10 LIN2 6.135,1.691 5.628,2.334 false 1.616,2.251 1.969,2.428 0.353,0.177 10 LIN2 2.027,1.715 1.761,2.25 false 0.287,0.257 0.554,0.434 0.267,0.177 10 *a 4.736,0.257 5.003,0.434 0.267,0.177 10 *b


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

This inspection is to check the LIN line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


Standard Resistance:
Tester Connection Condition Specified Condition
3B-12 (LIN2) - MB-16 (LIN2) Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
*b Component without harness connected
(Instrument Panel Junction Block Assembly)


d.

Install the main body ECU (multiplex network body ECU) to the instrument panel junction block assembly.


e.

Install the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION).



OK

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR - AUXILIARY BATTERY, BODY GROUND)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR - AUXILIARY BATTERY, BODY GROUND)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
J3-2 (B) - Body ground Power switch off 11 to 14 V

for RHD
Tester Connection Condition Specified Condition
H3-2 (B) - Body ground Power switch off 11 to 14 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
J3-1 (GND) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
H3-1 (GND) - Body ground Always Below 1 Ω




OK

4.REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for DRIVER DOOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for DRIVER DOOR)
a.

Replace the power window regulator motor assembly (for driver door) (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Front Door)>REMOVAL).



NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT

b.

Check for DTCs.

OK:

DTC B2321 is not output.




OK

END (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for DRIVER DOOR) WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)