Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM › 2011.12–2014.12
RM2170E _58 Vehicle Interior _057034 DOOR LOCK _0278072 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  Only Back Door cannot be Opened  


DESCRIPTION

The main body ECU (multiplex network body ECU) receives signals from the back door opener switch assembly. Then, the main body ECU (multiplex network body ECU) activates the back door lock motor.

WIRING DIAGRAM

B308524E03
4.551,3.433 6.207,3.746 1.656,0.313 10 Main Body ECU (Multiplex Network Body ECU) 1.534,2.513 3.181,2.687 1.647,0.174 10 Back Door Lock Assembly 1.422,5.137 3.699,5.312 2.276,0.174 10 Back Door Opener Switch Assembly 1.534,2.326 1.723,2.467 0.188,0.141 10 T5 1.422,4.974 1.699,5.139 0.276,0.165 10 T6 5.247,5.609 6.801,5.969 1.554,0.360 10 Certification ECU (Smart Key ECU Assembly) 5.247,5.446 5.533,5.592 0.286,0.147 10 G53 4.173,1.205 4.374,1.370 0.201,0.165 10 3D 4.173,1.906 4.385,2.071 0.211,0.165 10 3D 5.196,1.107 5.369,1.247 0.173,0.140 10 20 5.266,1.807 5.385,1.973 0.119,0.165 10 6 2.786,1.793 3.164,1.935 0.378,0.142 10 ACT+ 3.049,4.624 3.173,4.766 0.125,0.142 10 B 1.963,4.624 2.088,4.766 0.125,0.142 10 L 2.952,1.1 3.152,1.242 0.200,0.142 10 D+ 1.602,1.793 1.946,1.935 0.343,0.142 10 ACT- 1.406,1.793 1.513,1.940 0.107,0.147 10 2 3.234,1.807 3.342,1.954 0.107,0.147 10 1 3.234,1.1 3.342,1.249 0.107,0.149 10 3 4.222,1.709 4.336,1.875 0.114,0.165 10 9 4.173,1.011 4.364,1.176 0.191,0.165 10 35 5.161,4.605 5.351,4.770 0.191,0.165 10 22 3.254,4.596 3.361,4.779 0.107,0.184 10 3 1.783,4.596 1.890,4.779 0.107,0.184 10 2 5.42,4.694 5.868,4.843 0.448,0.149 10 TSW5 5.448,1.212 5.896,1.361 0.448,0.149 10 BCTY 4.551,3.258 4.807,3.407 0.255,0.149 10 MB 5.448,1.871 5.736,2.019 0.288,0.149 10 TR+ 0.84,6.249 2.580,6.412 1.739,0.163 10 : CAN Communication Line 3.697,2.275 5.353,2.588 1.656,0.313 10 Instrument Panel Junction Block Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

The power door lock control system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the power door lock control system after confirming that the communication systems are functioning properly.



PROCEDURE

1.CHECK POWER DOOR LOCK OPERATION (BASIC FUNCTION)
a.

Check the power door lock basic function (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).

OK:

The power door lock basic functions operate normally.




OK

2.READ VALUE USING INTELLIGENT TESTER (DOOR LOCK STATUS)

NG

2.READ VALUE USING INTELLIGENT TESTER (DOOR LOCK STATUS)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.


Main Body (Main Body ECU (Multiplex Network Body ECU))
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Back Door Open Back door lock/Permit or Prohibt Permit: Back door unlocked
Prohibt: Back door locked
-

OK:

The intelligent tester indicates Permit or Prohibit according to the door lock operation shown in the table.



OK

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.

Main Body (Main Body ECU (Multiplex Network Body ECU))
Tester Display Test Part Control Range Diagnostic Note
Trunk and Back-Door Open Operate back door lock motor ON or OFF -

OK:

The back door lock assembly unlatches when ON is selected.




OK

GO TO SMART ENTRY AND START SYSTEM

NG

4.INSPECT BACK DOOR LOCK ASSEMBLY
4.INSPECT BACK DOOR LOCK ASSEMBLY
a.
E345500E01
0.365,0.135 0.677,0.333 0.313,0.198 10 false *b 0.417,2.51 0.729,2.708 0.313,0.198 10 false *c

E345501E01
1.698,1.771 1.698,1.271 false 1.25,1.698 1.5,1.698 1.5,1.698 1.5,1.281 false 2.146,1.698 1.896,1.698 1.896,1.698 1.896,1.281 false 0.083,0.104 0.396,0.302 0.313,0.198 10 false *a 0.99,1.594 1.302,1.792 0.313,0.198 10 false D+ 1.542,1.813 2,2.052 0.458,0.24 10 false ACT- 2.208,1.625 2.667,1.865 0.458,0.24 10 false ACT+

Remove the back door lock assembly (See page Vehicle Interior>DOOR LOCK>BACK DOOR LOCK>REMOVAL).


b.

Check the operation of the door lock motor.

i.

Move the door lock to the lock position.


ii.

Apply auxiliary battery voltage to the door lock motor and check the operation of the door lock motor.

OK:
Connection Result
Auxiliary battery positive (+) → Terminal 1 (ACT+)
Auxiliary battery negative (-) → Terminal 2 (ACT-)
Unlocks




c.

Check the operation of the door courtesy switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 (ACT-) - 3 (D+) Locked 10 kΩ or higher
2 (ACT-) - 3 (D+) Unlocked Below 1 Ω


Text in Illustration
*a Component without harness connected
(Back Door Lock Assembly)
*b Lock
*c Unlock




OK

5.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPLACE BACK DOOR LOCK ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the 3D instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T5-1 (ACT+) - 3D-9 (TR+) Always Below 1 Ω
T5-1 (ACT+) - Body ground Always 10 kΩ or higher
T5-3 (D+) - 3D-35 (BCTY) Always Below 1 Ω
T5-3 (D+) - Body ground Always 10 kΩ or higher
T5-2 (ACT-) - Body ground Always Below 1 Ω




OK

6.REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Replace the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).



NEXT

7.CHECK BACK DOOR OPEN OPERATION
7.CHECK BACK DOOR OPEN OPERATION
a.

Check that the back door can be opened.

OK:

The back door can be opened normally.




OK

END (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)