Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM › 2011.12–2017.06
RM2170E _58 Vehicle Interior _057034 DOOR LOCK _0278072 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  All Doors LOCK/UNLOCK Functions do not Operate Via Door Control Switch or Door Key Cylinder  


DESCRIPTION

The main body ECU (multiplex network body ECU) receives switch signals from the door control switch (power window regulator master switch assembly) and driver door key cylinder lock or unlock switch signals from the front door lock assembly LH*1 or front door lock assembly RH*2. The main body ECU (multiplex network body ECU) activates the door lock motor on each door according to these signals.

·

*1: for LHD

·

*2: for RHD


WIRING DIAGRAM

B296423E09
5.464,5.006 7.110,5.324 1.647,0.318 10 Main Body ECU (Multiplex Network Body ECU) 0.686,2.108 3.270,2.419 2.584,0.311 10 Door Key Lock and Unlock Switch (Front Door Lock Assembly LH*1/RH*2) 0.632,4.556 2.906,4.878 2.274,0.323 10 Door Control Switch (Power Window Regulator Master Switch Assembly) 1.124,1.371 1.375,1.510 0.251,0.140 10 7*1 1.124,1.231 1.375,1.370 0.251,0.140 10 8*2 2.225,1.647 2.655,1.787 0.429,0.140 10 10*1 2.296,1.507 2.725,1.647 0.429,0.140 10 5*2 2.225,1.101 2.492,1.241 0.267,0.140 10 9*1 2.225,0.961 2.492,1.101 0.267,0.140 10 6*2 1.124,3.479 1.352,3.619 0.228,0.140 10 9*2 1.124,3.619 1.352,3.759 0.228,0.140 10 1*1 2.221,3.326 2.447,3.466 0.226,0.140 10 9*1 2.225,3.868 2.330,4.008 0.105,0.140 10 2 5.778,1.036 5.954,1.175 0.177,0.140 10 11 5.778,1.61 5.954,1.750 0.177,0.140 10 12 5.813,3.873 5.919,4.012 0.106,0.140 10 9 5.77,3.312 5.962,3.452 0.193,0.140 10 10 1.949,3.285 2.156,3.427 0.207,0.142 10 UL 2.047,4.07 2.156,4.212 0.110,0.142 10 L 1.421,3.608 1.540,3.750 0.119,0.142 10 E 1.958,1.814 2.174,1.956 0.216,0.142 10 UL 2.066,1.025 2.175,1.167 0.110,0.142 10 L 1.43,1.366 1.549,1.508 0.119,0.142 10 E 6.037,1.176 6.214,1.315 0.177,0.140 10 L2 6.037,1.736 6.311,1.876 0.274,0.140 10 UL2 6.037,3.992 6.214,4.131 0.177,0.140 10 L1 6.037,3.431 6.311,3.571 0.274,0.140 10 UL1 5.464,4.825 5.757,4.965 0.293,0.140 10 G59 0.632,4.382 0.934,4.521 0.302,0.140 10 J1*1 0.945,4.382 1.274,4.521 0.329,0.140 10 H1*2 0.686,1.93 1.371,2.070 0.686,0.140 10 J6*1, H6*2 3.725,5.05 4.462,5.203 0.737,0.154 10 *2: for RHD 3.725,4.713 4.434,4.867 0.709,0.154 10 *1: for LHD 2.221,3.196 2.455,3.335 0.235,0.140 10 8*2

PROCEDURE

1.CHECK DOOR LOCK OPERATION
a.

Check door lock operation (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).

Result:
Result Proceed to
All doors cannot be locked through door control switch (power window regulator master switch assembly) A
All doors cannot be locked through driver door key cylinder B




A

2.READ VALUE USING INTELLIGENT TESTER (DOOR CONTROL SWITCH (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY))

B

5.READ VALUE USING INTELLIGENT TESTER (DOOR KEY-LINKED LOCK AND UNLOCK SWITCH)
2.READ VALUE USING INTELLIGENT TESTER (DOOR CONTROL SWITCH (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY))
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Main Body (Main Body ECU (Multiplex Network Body ECU))
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Door Lock SW-Lock Door control switch (power window regulator master switch assembly) lock signal/ON or OFF ON: Lock side of door control switch (power window regulator master switch assembly) pushed
OFF: Lock side of door control switch (power window regulator master switch assembly) not pushed
-
Door Lock SW-Unlock Door control switch (power window regulator master switch assembly) unlock signal/ON or OFF ON: Unlock side of door control switch (power window regulator master switch assembly) pushed
OFF: Unlock side of door control switch (power window regulator master switch assembly) not pushed
-

OK:

The intelligent tester indicates ON or OFF according to the switch operation shown in the table above.




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

3.INSPECT DOOR CONTROL SWITCH (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY)
3.INSPECT DOOR CONTROL SWITCH (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY)
a.

for LHD

i.
B302422E07
1.098,1.699 1.098,0.904 1.098,0.904 0.793,0.904 false 2.336,1.701 2.336,0.984 2.336,0.984 2.605,0.984 false 2.179,1.698 2.179,0.477 2.179,0.477 2.605,0.477 false 0.206,0.217 0.398,0.388 0.192,0.171 10 *a 2.65,0.905 2.761,1.048 0.111,0.143 10 E 2.65,0.394 2.745,0.534 0.095,0.140 10 L 0.542,0.823 0.751,0.963 0.209,0.140 10 UL

Remove the door control switch (power window regulator master switch assembly) (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (L) - 1 (E) Lock switch pushed Below 1 Ω
2 (L) - 1 (E) Lock switch not pushed 10 kΩ or higher
9 (UL) - 1 (E) Unlock switch pushed Below 1 Ω
9 (UL) - 1 (E) Unlock switch pushed 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Door Control Switch (Power Window Regulator Master Switch Assembly))



b.

for RHD

i.
B302422E19
1.253,1.682 1.253,0.543 1.253,0.543 0.948,0.543 false 1.11,1.684 1.11,0.967 1.11,0.967 0.841,0.967 false 2.188,1.69 2.188,0.71 2.188,0.71 2.615,0.71 false 0.206,0.217 0.398,0.388 0.192,0.171 10 *a 0.681,0.892 0.791,1.035 0.111,0.143 10 E 2.653,0.634 2.748,0.774 0.095,0.140 10 L 0.671,0.465 0.880,0.604 0.209,0.140 10 UL

Remove the door control switch (power window regulator master switch assembly) (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (L) - 9 (E) Lock switch pushed Below 1 Ω
2 (L) - 9 (E) Lock switch not pushed 10 kΩ or higher
8 (UL) - 9 (E) Unlock switch pushed Below 1 Ω
8 (UL) - 9 (E) Unlock switch pushed 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Door Control Switch (Power Window Regulator Master Switch Assembly))




OK

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the G59 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
J1-2 (L) - G59-9 (L1) Always Below 1 Ω
J1-9 (UL) - G59-10 (UL1) Always Below 1 Ω
J1-1 (E) - Body ground Always Below 1 Ω
J1-2 (L) - Body ground Always 10 kΩ or higher
J1-9 (UL) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
H1-2 (L) - G59-9 (L1) Always Below 1 Ω
H1-8 (UL) - G59-10 (UL1) Always Below 1 Ω
H1-9 (E) - Body ground Always Below 1 Ω
H1-2 (L) - Body ground Always 10 kΩ or higher
H1-8 (UL) - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.READ VALUE USING INTELLIGENT TESTER (DOOR KEY-LINKED LOCK AND UNLOCK SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Main Body (Main Body ECU (Multiplex Network Body ECU))
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Door Key SW-Lock Driver door key-linked lock/unlock switch lock signal/ON or OFF ON: Driver door key cylinder turned to lock position
OFF: Driver door key cylinder not turned to lock position
-
Door Key SW-Unlock Driver door key-linked lock/unlock switch unlock signal/ON or OFF ON: Driver door key cylinder turned to unlock position
OFF: Driver door key cylinder not turned to unlock position
-

OK:

The intelligent tester indicates ON or OFF according to the key cylinder operation shown in the table.




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

6.INSPECT FRONT DOOR LOCK ASSEMBLY
6.INSPECT FRONT DOOR LOCK ASSEMBLY
a.

for LHD

i.

Remove the front door lock assembly LH (See page Vehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL).


ii.
B280166E03
0.101,0.076 0.266,0.241 0.165,0.165 10 *a 2.851,1.623 3.016,1.788 0.165,0.165 10 *b 3.057,0.558 3.223,0.723 0.165,0.165 10 *c 2.273,3.437 2.273,3.802 2.273,3.802 2.086,3.802 false 2.427,3.437 2.427,4.115 2.427,4.115 1.931,4.115 false 2.737,3.437 2.737,4.436 2.737,4.436 2.086,4.436 false 1.927,4.36 2.044,4.502 0.117,0.142 10 E 1.79,4.034 1.906,4.176 0.117,0.142 10 L 1.833,3.716 2.033,3.858 0.200,0.142 10 UL

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
9 (L) - 7 (E) Turned to lock Below 1 Ω
9 (L) - 7 (E) Not turned 10 kΩ or higher
10 (UL) - 7 (E) Turned to unlock Below 1 Ω
10 (UL) - 7 (E) Not turned 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Front Door Lock Assembly LH)
*b Unlock
*c Lock



b.

for RHD

i.

Remove the front door lock assembly RH (See page Vehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL).


ii.
B280267E07
0.104,0.072 0.259,0.221 0.155,0.149 10 *a 0.291,0.782 0.446,0.931 0.155,0.149 10 *c 0.634,1.915 0.789,2.065 0.155,0.149 10 *b 0.772,3.514 0.772,4.445 0.772,4.445 1.367,4.445 false 1.047,3.514 1.047,4.13 1.047,4.13 1.367,4.13 false 1.185,3.514 1.185,3.809 1.185,3.809 1.367,3.809 false 1.387,4.353 1.503,4.495 0.117,0.142 10 E 1.387,4.044 1.496,4.186 0.110,0.142 10 L 1.387,3.729 1.596,3.871 0.209,0.142 10 UL

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (L) - 8 (E) Turned to lock Below 1 Ω
6 (L) - 8 (E) Not turned 10 kΩ or higher
5 (UL) - 8 (E) Turned to unlock Below 1 Ω
5 (UL) - 8 (E) Not turned 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Front Door Lock Assembly RH)
*b Unlock
*c Lock




OK

7.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPLACE FRONT DOOR LOCK ASSEMBLY LH

7.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the G59 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
J6-9 (L) - G59-11 (L2) Always Below 1 Ω
J6-10 (UL) - G59-12 (UL2) Always Below 1 Ω
J6-7 (E) - Body ground Always Below 1 Ω
G59-11 (L2) - Body ground Always 10 kΩ or higher
G59-12 (UL2) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
H6-6 (L) - G59-11 (L2) Always Below 1 Ω
H6-5 (UL) - G59-12 (UL2) Always Below 1 Ω
H6-8 (E) - Body ground Always Below 1 Ω
G59-11 (L2) - Body ground Always 10 kΩ or higher
G59-12 (UL2) - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR