Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Entry Function) › 2014.12–2015.11
RM2170E _58 Vehicle Interior _057035 THEFT DETERRENT / KEYLESS ENTRY _0278080 SMART ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  Driver Side Door Entry Lock and Unlock Functions do not Operate  


DESCRIPTION

If the entry lock and unlock functions do not operate for the driver door only, the request code may not be being transmitted from the driver door or the front door outside handle assembly (for driver door) (touch sensor) may be malfunctioning. If the entry functions for other doors operate properly, communication between the electrical key transmitter sub-assembly and door control receiver is normal. In this case, there may be a problem with request code transmission (communication between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door) [driver door electrical key antenna]), or there may be wave interference.

HINT:

If the cause of the malfunction is stored in the certification ECU (smart key ECU assembly), the following table is helpful in checking whether or not the malfunction was caused by wave interference.


WIRING DIAGRAM

B349521E83
0.167,3.656 1.833,4.344 1.667,0.688 10 false Front Door Outside Handle Assembly (for Driver Door) 0.177,3.49 1.25,3.823 1.073,0.333 10 false J10*1 H10*2 5.417,3.521 6.969,4.031 1.552,0.51 10 false Certification ECU (Smart Key ECU Assembly) 1.313,0.729 1.854,0.938 0.542,0.208 10 false ANT1 1.302,1.198 1.844,1.406 0.542,0.208 10 false ANT2 1.552,1.667 2.094,1.875 0.542,0.208 10 false B 1.271,2.125 1.813,2.333 0.542,0.208 10 false SENS 1.302,2.583 1.844,2.792 0.542,0.208 10 false TRG+ 1.375,3.031 1.917,3.24 0.542,0.208 10 false GND 1.781,0.604 2.323,0.813 0.542,0.208 10 false 6 1.792,1.063 2.333,1.271 0.542,0.208 10 false 3 1.792,1.521 2.333,1.729 0.542,0.208 10 false 5 1.792,1.99 2.333,2.198 0.542,0.208 10 false 4 1.781,2.438 2.323,2.646 0.542,0.208 10 false 1 1.792,2.906 2.333,3.115 0.542,0.208 10 false 2 5.427,0.542 5.969,0.75 0.542,0.208 10 false 12 5.375,0.729 5.708,0.938 0.333,0.208 10 false G79 5.385,1.188 5.719,1.396 0.333,0.208 10 false G79 5.375,1.646 5.708,1.854 0.333,0.208 10 false G79 5.375,2.104 5.708,2.313 0.333,0.208 10 false G79 5.375,2.563 5.708,2.771 0.333,0.208 10 false G79 5.375,3.021 5.708,3.229 0.333,0.208 10 false G77 5.438,1 5.979,1.208 0.542,0.208 10 false 13 5.427,1.458 5.969,1.667 0.542,0.208 10 false 19 5.427,1.917 5.969,2.125 0.542,0.208 10 false 22 5.427,2.375 5.969,2.583 0.542,0.208 10 false 20 5.438,2.833 5.979,3.042 0.542,0.208 10 false 11 5.74,0.74 6.281,0.948 0.542,0.208 10 false CLG1 5.74,1.188 6.281,1.396 0.542,0.208 10 false CG1B 5.74,1.656 6.281,1.865 0.542,0.208 10 false POS1 5.74,2.115 6.281,2.323 0.542,0.208 10 false SEN1 5.74,2.583 6.281,2.792 0.542,0.208 10 false TSW1 5.75,3.031 6.292,3.24 0.542,0.208 10 false E 3.146,3.958 4.063,4.24 0.917,0.281 10 false *1: for LHD 3.146,4.229 4.25,4.438 1.104,0.208 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the intelligent tester with the power switch off to troubleshoot:

Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>DTC CHECK / CLEAR).

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).

OK:

Door locks operate normally.




OK

2.CHECK WAVE ENVIRONMENT

NG

2.CHECK WAVE ENVIRONMENT
a.
B300377E02
2.354,1.167 2.563,1.354 0.208,0.188 10 false *a 1.26,3.479 1.469,3.667 0.208,0.188 10 false *a 0.125,0.083 0.542,0.49 0.417,0.406 10 true *A 0.177,2.302 0.75,2.458 0.573,0.156 10 false *B

Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the front door outside handle assembly (for driver door) and perform an entry function check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

Text in Illustration
*A for LHD
*B for RHD
*a Approximately 0.3 m (0.984 ft.)

NOTICE:

If the electrical key transmitter sub-assembly is brought within 0.2 m (0.656 ft.) of the door handle, communication may not be possible.


HINT:

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.


Result:
Result Proceed to
Entry function does not operate normally. A
Entry function operates normally. B




A

3.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU)

B

AFFECTED BY WAVE INTERFERENCE

3.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU)
a.

Disconnect the J10*1 or H10*2 front door outside handle assembly (for driver door) connector.


b.

Disconnect the G79 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

*1: for LHD

*2: for RHD


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
J10-3 (ANT2) - G79-13 (CG1B) Always Below 1 Ω
J10-6 (ANT1) - G79-12 (CLG1) Always Below 1 Ω
J10-5 (B) - G79-19 (POS1) Always Below 1 Ω
J10-2 (GND) - Body ground Always Below 1 Ω
J10-3 (ANT2) or G79-13 (CG1B) - Body ground Always 10 kΩ or higher
J10-6 (ANT1) or G79-12 (CLG1) - Body ground Always 10 kΩ or higher
J10-5 (B) or G79-19 (POS1) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
H10-3 (ANT2) - G79-13 (CG1B) Always Below 1 Ω
H10-6 (ANT1) - G79-12 (CLG1) Always Below 1 Ω
H10-5 (B) - G79-19 (POS1) Always Below 1 Ω
H10-2 (GND) - Body ground Always Below 1 Ω
H10-3 (ANT2) or G79-13 (CG1B) - Body ground Always 10 kΩ or higher
H10-6 (ANT1) or G79-12 (CLG1) - Body ground Always 10 kΩ or higher
H10-5 (B) or G79-19 (POS1) - Body ground Always 10 kΩ or higher




OK

4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO DRIVER DOOR ELECTRICAL KEY ANTENNA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO DRIVER DOOR ELECTRICAL KEY ANTENNA)
a.
U183367E02
2.469,0.198 2.229,0.198 2.229,0.198 1.833,0.771 false 2.521,1.354 2.25,1.354 2.25,1.354 1.833,0.885 false 1.698,0.729 1.698,0.146 1.698,0.146 1.375,0.146 false 1.698,0.938 1.698,1.521 1.698,1.521 1.375,1.521 false 0.083,0.094 0.344,0.344 0.26,0.25 10 false *a 0.063,1.531 0.323,1.781 0.26,0.25 10 false *1 0.115,2.479 0.448,2.677 0.333,0.198 10 false GND 2.552,1.271 2.948,1.469 0.396,0.198 10 false ANT1 0.458,0.542 0.844,0.708 0.385,0.167 10 false J10 2.531,0.125 2.948,0.271 0.417,0.146 10 false ANT2 0.438,0.938 0.802,1.104 0.365,0.167 10 false H10 0.885,0.521 1.063,0.688 0.177,0.167 10 false *A 0.885,0.938 1.063,1.104 0.177,0.167 10 false *B 1.229,1.427 1.375,1.594 0.146,0.167 10 false B 1.031,0.052 1.406,0.219 0.375,0.167 10 false GND

Disconnect the J10*1 or H10*2 front door outside handle assembly (for driver door) connector.


b.

Connect the G79 certification ECU (smart key ECU assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
J10-5 (B) - J10-2 (GND)*1
H10-5 (B) - H10-2 (GND)*2
Power switch off → on (IG) 9 to 12 V → Below 2 V



d.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Switch Condition Tool Setting Specified Condition
J10-3 (ANT2) - J10-6 (ANT1)*1
H10-3 (ANT2) - H10-6 (ANT1)*2
Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought outside detection area

6.

All doors locked through wireless operation


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform)



*1: for LHD

*2: for RHD


Text in Illustration
*A for LHD
*B for RHD
*1 Waveform
*a Front view of wire harness connector
(to Front Door Outside handle assembly (for driver door))


OK

5.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

5.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR)
a.

Temporarily replace the front door outside handle assembly (for driver door) with a new or known good one (See page Vehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY).



NEXT

6.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (OPERATION)
6.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (OPERATION)
a.

Check that the entry functions operate normally (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

OK:

Entry functions operate normally.




OK

END (FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)