Use the same procedure for both the RH and LH sides.
The procedure described below is for the LH side.
1. PRECAUTION
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
58165F
2.REMOVE FRONT FLOOR COVER RH
3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
4.REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)
Disengage the 10 claws and 4 guides.
Disconnect the connector and remove the power window regulator master switch assembly with front door armrest base panel.
5.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)
Disengage the 10 claws and 4 guides.
Disconnect the connector and remove the power window regulator switch assembly with front door armrest base panel.
67602
6.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY
Using a screwdriver with its tip wrapped in protective tape, disengage the claw and open the cover.
| *1 | Protective Tape |
Remove the 3 screws.
Disengage the 8 clips and remove the front door trim board sub-assembly as shown in the illustration.
Disconnect the front door lock remote control cable assembly and front door inside locking cable from the front door trim board sub-assembly.
| *1 | Front Door Inside Locking Cable Assembly |
| *2 | Front Door Lock Remote Control Cable Assembly |
69206B
7.REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY
Disengage the 4 guides and remove the front door inside handle sub-assembly.
68172A
8.REMOVE FRONT DOOR GLASS INNER WEATHERSTRIP
Disengage the 8 claws as show in the illustration and remove the front door glass inner weatherstrip.
9.REMOVE OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER
86160
10.REMOVE FRONT NO. 1 SPEAKER ASSEMBLY
86160P
11.REMOVE FRONT NO. 2 SPEAKER ASSEMBLY
67832
12.REMOVE FRONT DOOR SERVICE HOLE COVER
Remove the front door service hole cover.
Remove any remaining butyl tape from the front door panel.
68102
13.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY
Remove the front door No. 2 service hole cover.
Connect the cable to the negative (-) auxiliary battery terminal and power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.
Disconnect the negative (-) auxiliary battery terminal and power window regulator master switch assembly.
Remove the 2 bolts.
After the bolts are removed, do not allow the door glass to fall.
Remove the front door glass sub-assembly as shown in the illustration.
Do not damage the door glass.
14.REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY
Disconnect the connector.
Loosen the temporary bolt.
| *1 | Temporary Bolt |
Do not remove the temporary bolt. If the temporary bolt is removed, the front door power window regulator assembly may fall and cause damage.
Remove the 5 bolts and front door window regulator assembly.
Remove the temporary bolt from the front door window regulator assembly.
85720D
15.REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY
Using a T25 "TORX" socket wrench, remove the 3 screws and power window regulator motor assembly.
68210C
16.REMOVE FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY
68141C
17.REMOVE FRONT DOOR GLASS RUN
Disengage the 2 guides and remove the front door glass run in the order shown in the illustration.
68610
18.REMOVE FRONT DOOR CHECK ASSEMBLY
Remove the 3 bolts and the front door check assembly.
67862
19.REMOVE FRONT DOOR WEATHERSTRIP
Disengage the 30 clips and remove the front door weatherstrip.
67404F
20.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY
Remove the bolt.
Disengage the guide and remove the front door rear lower frame sub-assembly.
67401F
21.REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY
Remove the screw.
Remove the 2 bolts and remove the front door front lower frame sub-assembly.
68215
22.REMOVE FRONT DOOR FIX WINDOW WEATHERSTRIP
Slide the front door fix window weatherstrip, in the direction indicated by the arrow in the illustration, to remove it.
Remove the front door fix window glass from the front door fix window weatherstrip.
23.REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)
Remove the hole plug.
Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover with lock cylinder assembly.
The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.
69217F
24.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)
Using a screwdriver, disengage the claw and 2 guides to remove the front door outside handle cover as shown in the illustration.
69217E
25.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)
Remove the hole plug.
Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover.
The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.
69220
26.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY
Using a screwdriver, disengage the 3 claws and disconnect the connector as shown in the illustration.
Remove the front door outside handle assembly as shown in the illustration.
69241H
27.REMOVE FRONT DOOR OUTSIDE HANDLE FRONT PAD
Disengage the 3 claws and remove the front door outside handle front pad.
69242E
28.REMOVE FRONT DOOR OUTSIDE HANDLE REAR PAD
Disengage the 2 claws and remove the front door outside handle rear pad.
69320
29.REMOVE FRONT DOOR LOCK ASSEMBLY
Disconnect the connector.
| *1 | Front Door Lock Open Rod |
Using a T30 "TORX" socket wrench, remove the 3 screws.
Move the front door lock assembly downward and disconnect the front door lock open rod, and then remove the front door lock assembly.
When reusing the front door lock assembly:
Remove the door lock wiring harness seal from the front door lock assembly.
69710C
30.REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY
Remove the front door lock remote control cable assembly as shown in the illustration.
69760C
31.REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY
Using a screwdriver, disengage the 3 claws as shown in the illustration.
Remove the front door inside locking cable assembly as shown in the illustration.
69202A
32.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
Using a T30 "TORX" socket wrench, loosen the screw.
| *a | Outside |
| *b | Inside |
Slide the front door outside handle frame sub-assembly to disengage the door handle nut and 2 claws of the front door outside handle frame sub-assembly, and then remove it.
Remove the front door outside handle frame sub-assembly with the wire as shown in the illustration.
Disengage the 2 clamps and guide and remove the front door outside handle frame sub-assembly.
69312
33.REMOVE FRONT DOOR LOCK OPEN ROD
Remove the front door lock open rod as indicated by the arrows, in the order shown in the illustration.
67001A
34.REMOVE FRONT DOOR PANEL CUSHION
Disengage each claw and remove the 2 front door panel cushions.
75921C
35.REMOVE NO. 1 BLACK OUT TAPE