Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Entry Function) › 2011.12–2014.12
RM2170E _58 Vehicle Interior _057035 THEFT DETERRENT / KEYLESS ENTRY _0278080 SMART ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  Front Passenger Side Door Entry Lock Function does not Operate  


DESCRIPTION

If the entry lock function does not operate for the front passenger door only, but the entry unlock function operates, the request code is being transmitted properly from the front passenger door. In this case, there may be a problem related to the front door outside handle assembly (for front passenger door) (lock sensor) (connection between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for front passenger door) [lock sensor]).

WIRING DIAGRAM

B349521E81
0.396,3.667 2.031,4.25 1.635,0.583 10 false Front Door Outside Handle Assembly (for Front Passenger Door) 0.396,3.49 1.281,3.719 0.885,0.229 10 false H11*1 J11*2 5.396,3.5 6.948,4.01 1.552,0.51 10 false Certification ECU (Smart Key ECU Assembly) 1.313,0.729 1.854,0.938 0.542,0.208 10 false ANT1 1.302,1.198 1.844,1.406 0.542,0.208 10 false ANT2 1.552,1.667 2.094,1.875 0.542,0.208 10 false B 1.271,2.125 1.813,2.333 0.542,0.208 10 false SENS 1.302,2.583 1.844,2.792 0.542,0.208 10 false TRG+ 1.375,3.031 1.917,3.24 0.542,0.208 10 false GND 1.781,0.604 2.323,0.813 0.542,0.208 10 false 6 1.792,1.063 2.333,1.271 0.542,0.208 10 false 3 1.792,1.521 2.333,1.729 0.542,0.208 10 false 5 1.792,1.99 2.333,2.198 0.542,0.208 10 false 4 1.781,2.438 2.323,2.646 0.542,0.208 10 false 1 1.792,2.906 2.333,3.115 0.542,0.208 10 false 2 5.427,0.542 5.969,0.75 0.542,0.208 10 false 13 5.385,0.729 5.719,0.938 0.333,0.208 10 false G55 5.375,1.188 5.708,1.396 0.333,0.208 10 false G55 5.375,1.646 5.708,1.854 0.333,0.208 10 false G55 5.375,2.094 5.708,2.302 0.333,0.208 10 false G55 5.375,2.563 5.708,2.771 0.333,0.208 10 false G54 5.375,3.021 5.708,3.229 0.333,0.208 10 false G55 5.427,1 5.969,1.208 0.542,0.208 10 false 12 5.427,1.458 5.969,1.667 0.542,0.208 10 false 16 5.469,1.917 6.01,2.125 0.542,0.208 10 false 2 5.469,2.375 6.01,2.583 0.542,0.208 10 false 8 5.458,2.833 6,3.042 0.542,0.208 10 false 1 5.74,0.74 6.281,0.948 0.542,0.208 10 false CLG2 5.74,1.188 6.281,1.396 0.542,0.208 10 false CG2B 5.74,1.656 6.281,1.865 0.542,0.208 10 false POS2 5.74,2.115 6.281,2.323 0.542,0.208 10 false SEN2 5.74,2.583 6.281,2.792 0.542,0.208 10 false TSW2 5.75,3.031 6.292,3.24 0.542,0.208 10 false E 3.281,4 4.167,4.229 0.885,0.229 10 false *1: for LHD 3.292,4.323 4.177,4.552 0.885,0.229 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the intelligent tester with the power switch off to troubleshoot:

Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>DTC CHECK / CLEAR).

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).

OK:

Door locks operate normally.




OK

2.READ VALUE USING INTELLIGENT TESTER (LOCK SENSOR)

NG

2.READ VALUE USING INTELLIGENT TESTER (LOCK SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Entry&Start / Data List.


e.

Read the Data List according to the display on the intelligent tester.


Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
P-Door Trigger Switch Front passenger door touch sensor (lock sensor) / ON or OFF ON: Front passenger door touch sensor (lock sensor) touched
OFF: Front passenger door touch sensor (lock sensor) not touched
·

Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate.



OK:

The intelligent tester display changes correctly in response to the operation of the front door outside handle assembly (for front passenger door).



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU)
3.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU)
a.

Disconnect the H11*1 or J11*2 front door outside handle assembly (for front passenger door) connector.


b.

Disconnect the G54 and G55 certification ECU (smart key ECU assembly) connectors.


c.

Measure the resistance according to the value(s) in the table below.

*1: for LHD

*2: for RHD


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
H11-1 (TRG+) - G54-8 (TSW2) Always Below 1 Ω
G55-1 (E) - Body ground Always Below 1 Ω
H11-1 (TRG+) or G54-8 (TSW2) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
J11-1 (TRG+) - G54-8 (TSW2) Always Below 1 Ω
G55-1 (E) - Body ground Always Below 1 Ω
J11-1 (TRG+) or G54-8 (TSW2) - Body ground Always 10 kΩ or higher




OK

4.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR (FRONT PASSENGER DOOR LOCK SENSOR SIGNAL INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR (FRONT PASSENGER DOOR LOCK SENSOR SIGNAL INPUT)
a.

Connect the H11*1 or J11*2 front door outside handle assembly (for front passenger door) connector.

U183429E01
0.919,0.558 1.089,0.714 0.170,0.156 10 *a 4.17,2.786 4.339,2.942 0.170,0.156 10 *1 4.016,3.85 4.366,4.006 0.350,0.156 10 GND 5.635,2.091 5.805,2.247 0.170,0.156 10 E 5.482,2.786 5.652,2.942 0.170,0.156 10 *b 2.173,0.868 2.493,1.031 0.320,0.163 10 G53 4.86,0.868 5.180,1.031 0.320,0.163 10 G55 5.505,1.485 5.664,2.057 false 4.069,2.091 4.556,2.247 0.486,0.156 10 TSW2 4.103,1.616 4.258,2.055 false 5.021,3.272 5.502,2.94 5.502,2.94 5.336,3.276 false 3.601,0.861 3.922,1.024 0.320,0.163 10 G54

Text in Illustration
*1 Waveform - -
*a Component with harness connected
(Certification ECU (smart key ECU assembly))
*b In actuality, sampling is being performed

*1: for LHD

*2: for RHD



b.

Connect the G54 and G55 certification ECU (smart key ECU assembly) connectors.


c.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Switch Condition Tool Setting Specified Condition
G54-8 (TSW2) - G55-1 (E) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Front passenger door lock sensor not touched → touched


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform)




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR)