Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR › 2011.12–2014.12
RM2170E _59 Vehicle Exterior _057046 DOOR / HATCH _0278160 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for both the RH and LH sides.

·

The procedure described below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 4.REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

a.
B307078

Disengage the 10 claws and 4 guides.


b.

Disconnect the connector and remove the power window regulator master switch assembly with front door armrest base panel.


Hide 5.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

a.
B307079

Disengage the 10 claws and 4 guides.

i.

Disconnect the connector and remove the power window regulator switch assembly with front door armrest base panel.



Hide 67602 6.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

a.
B307080E02
1.448,1.333 1.448,1.635 false 1.365,1.656 1.615,1.854 0.25,0.198 10 true *1

Using a screwdriver with its tip wrapped in protective tape, disengage the claw and open the cover.

Text in Illustration
*1 Protective Tape


b.
B307081

Remove the 3 screws.


c.
B307082

Disengage the 8 clips and remove the front door trim board sub-assembly as shown in the illustration.


d.
B307083E03
2.333,1.354 2.677,1.021 true 2.271,1.625 2.521,1.823 false 2.698,0.917 2.979,1.104 0.281,0.188 10 true *1 2.552,1.76 2.813,1.969 0.26,0.208 10 true *2

Disconnect the front door lock remote control cable assembly and front door inside locking cable from the front door trim board sub-assembly.

Text in Illustration
*1 Front Door Inside Locking Cable Assembly
*2 Front Door Lock Remote Control Cable Assembly


Hide 69206B 7.REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B307084

Disengage the 4 guides and remove the front door inside handle sub-assembly.


Hide 68172A 8.REMOVE FRONT DOOR GLASS INNER WEATHERSTRIP

a.
B307085

Disengage the 8 claws as show in the illustration and remove the front door glass inner weatherstrip.


Hide 9.REMOVE OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER

Hide 86160 10.REMOVE FRONT NO. 1 SPEAKER ASSEMBLY

Hide 86160P 11.REMOVE FRONT NO. 2 SPEAKER ASSEMBLY

Hide 67832 12.REMOVE FRONT DOOR SERVICE HOLE COVER

a.
B308297

Remove the front door service hole cover.

NOTICE:

Remove any remaining butyl tape from the front door panel.



Hide 68102 13.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

a.
B307087

Remove the front door No. 2 service hole cover.


b.

Connect the cable to the negative (-) auxiliary battery terminal and power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.


c.

Disconnect the negative (-) auxiliary battery terminal and power window regulator master switch assembly.


d.
B307088

Remove the 2 bolts.

NOTICE:

After the bolts are removed, do not allow the door glass to fall.



e.
B307089

Remove the front door glass sub-assembly as shown in the illustration.

NOTICE:

Do not damage the door glass.



Hide 14.REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY

a.
B307090E02
2.146,0.813 2,0.813 true 1.823,0.771 1.979,0.917 0.156,0.146 10 true *1

Disconnect the connector.


b.

Loosen the temporary bolt.

Text in Illustration
*1 Temporary Bolt

NOTICE:

Do not remove the temporary bolt. If the temporary bolt is removed, the front door power window regulator assembly may fall and cause damage.



c.

Remove the 5 bolts and front door window regulator assembly.


d.

Remove the temporary bolt from the front door window regulator assembly.


Hide 85720D 15.REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY

a.
B307091

Using a T25 "TORX" socket wrench, remove the 3 screws and power window regulator motor assembly.


Hide 68210C 16.REMOVE FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY

Hide 68141C 17.REMOVE FRONT DOOR GLASS RUN

a.
B450303E02
1.635,0.688 1.958,0.938 0.323,0.25 10 false 1 2.042,1.01 2.25,1.208 0.208,0.198 10 true 2 1.302,0.49 1.625,0.74 0.323,0.25 10 false 3

Disengage the 2 guides and remove the front door glass run in the order shown in the illustration.


Hide 68610 18.REMOVE FRONT DOOR CHECK ASSEMBLY

a.
B307093

Remove the 3 bolts and the front door check assembly.


Hide 67862 19.REMOVE FRONT DOOR WEATHERSTRIP

a.
B307094

Disengage the 30 clips and remove the front door weatherstrip.


Hide 67404F 20.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

a.
B307095

Remove the bolt.


b.

Disengage the guide and remove the front door rear lower frame sub-assembly.


Hide 67401F 21.REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY

a.
B307096

Remove the screw.


b.

Remove the 2 bolts and remove the front door front lower frame sub-assembly.


Hide 68215 22.REMOVE FRONT DOOR FIX WINDOW WEATHERSTRIP

a.
B307097

Slide the front door fix window weatherstrip, in the direction indicated by the arrow in the illustration, to remove it.


b.

Remove the front door fix window glass from the front door fix window weatherstrip.


Hide 23.REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)

a.
B299844

Remove the hole plug.


b.
B307098

Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover with lock cylinder assembly.

HINT:

The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.



Hide 69217F 24.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)

a.
B307099

Using a screwdriver, disengage the claw and 2 guides to remove the front door outside handle cover as shown in the illustration.


Hide 69217E 25.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)

a.
B297584

Remove the hole plug.


b.
B300049

Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover.

HINT:

The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.



Hide 69220 26.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY

a.
B307100

Using a screwdriver, disengage the 3 claws and disconnect the connector as shown in the illustration.


b.
B307101

Remove the front door outside handle assembly as shown in the illustration.


Hide 69241H 27.REMOVE FRONT DOOR OUTSIDE HANDLE FRONT PAD

a.
B307102

Disengage the 3 claws and remove the front door outside handle front pad.


Hide 69242E 28.REMOVE FRONT DOOR OUTSIDE HANDLE REAR PAD

a.
B307103

Disengage the 2 claws and remove the front door outside handle rear pad.


Hide 69320 29.REMOVE FRONT DOOR LOCK ASSEMBLY

a.
B307104E03
0.74,0.385 0.833,0.385 true 0.854,0.302 1.021,0.458 0.167,0.156 10 true *1

Disconnect the connector.

Text in Illustration
*1 Front Door Lock Open Rod


b.

Using a T30 "TORX" socket wrench, remove the 3 screws.


c.

Move the front door lock assembly downward and disconnect the front door lock open rod, and then remove the front door lock assembly.


d.

When reusing the front door lock assembly:

i.
B307105

Remove the door lock wiring harness seal from the front door lock assembly.



Hide 69710C 30.REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

a.
B307106

Remove the front door lock remote control cable assembly as shown in the illustration.


Hide 69760C 31.REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY

a.
B307107

Using a screwdriver, disengage the 3 claws as shown in the illustration.


b.
B307108

Remove the front door inside locking cable assembly as shown in the illustration.


Hide 69202A 32.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.
B307109E02
0.135,2.552 0.281,2.708 0.146,0.156 10 false *b 0.135,0.115 0.354,0.323 0.219,0.208 10 true *a

Using a T30 "TORX" socket wrench, loosen the screw.

Text in Illustration
*a Outside
*b Inside


b.

Slide the front door outside handle frame sub-assembly to disengage the door handle nut and 2 claws of the front door outside handle frame sub-assembly, and then remove it.


c.
B307110

Remove the front door outside handle frame sub-assembly with the wire as shown in the illustration.


d.

Disengage the 2 clamps and guide and remove the front door outside handle frame sub-assembly.


Hide 69312 33.REMOVE FRONT DOOR LOCK OPEN ROD

a.
B307111E02
3.083,0.771 3.292,0.969 0.208,0.198 10 false (2) 2.604,0.167 2.813,0.365 0.208,0.198 10 false (1)

Remove the front door lock open rod as indicated by the arrows, in the order shown in the illustration.


Hide 67001A 34.REMOVE FRONT DOOR PANEL CUSHION

a.
B307112

Disengage each claw and remove the 2 front door panel cushions.