If code verification cannot be performed in the vehicle interior, there may be problems with the communication between the vehicle (indoor electrical key antenna assembly (front floor), (steering column) or (rear floor)) and electrical key transmitter sub-assembly, or the certification ECU (smart key ECU assembly) may be malfunctioning. When the electrical key transmitter sub-assembly is brought into the vehicle, verification of the key ID code transmitted from the electrical key transmitter sub-assembly and the key ID code stored in the certification ECU (smart key ECU assembly) is performed. If verification cannot be performed or the codes do not match, the power switch cannot be turned on (IG) and the hybrid system cannot be started.
When a door is unlocked and the electrical key transmitter sub-assembly is brought into the vehicle, the certification ECU (smart key ECU assembly) activates the indoor electrical key antenna assembly which transmits radio waves to detect the electrical key transmitter sub-assembly. If the electrical key transmitter sub-assembly recognizes that it is in the detection area, it responds with the key ID code. This information is received by the indoor electrical key antenna and then sent to the certification ECU (smart key ECU assembly).
The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
When using the intelligent tester with the power switch off to troubleshoot:
Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.
Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).
After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".
The indoor electrical key antenna assemblies have an antenna coil between each two CLG terminals.
The door control receiver is also related to interior verification.
Check that the entry lock and unlock functions operate for each door (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).
All door entry lock and unlock functions operate normally.
If the door control receiver is defective, code verification does not begin in the cabin and the entry functions do not operate.
OK
NG
Remove the transmitter battery of the electrical key transmitter sub-assembly (See page Vehicle Interior>DOOR LOCK>TRANSMITTER BATTERY>REPLACEMENT).
With the brake pedal depressed, face the logo side of the electrical transmitter sub-assembly towards the power switch, hold the transmitter near the power switch and then press the power switch.
When operating the power switch, check whether the hybrid system starts.
When the electrical key transmitter sub-assembly cannot be verified even though it is inside the detection area, the hybrid system start check can be performed by removing the transmitter battery from the electrical key transmitter sub-assembly and holding the electrical key transmitter sub-assembly near the power switch.
If the hybrid system cannot be started when performing this inspection, the certification ECU (smart key ECU assembly), steering lock ECU (Steering lock actuator assembly) or ID code box (immobiliser code ECU) may be malfunctioning.
Hybrid system starts.
| *1 | Power Switch |
| *2 | Electrical Key Transmitter Sub-assembly |
OK
NG
Install the transmitter battery to the electrical key transmitter sub-assembly (See page Vehicle Interior>DOOR LOCK>TRANSMITTER BATTERY>REPLACEMENT).
Bring the electrical key transmitter sub-assembly near the No. 1 indoor electrical key antenna assembly (front floor) and perform a smart entry and start system check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Driver Side)>REMOVAL).
Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 1 indoor electrical key antenna assembly (front floor).
Bring the electrical key transmitter sub-assembly near the No. 2 indoor electrical key antenna assembly (steering column) and perform a smart entry and start system check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Front Side)>REMOVAL)
Check that the customize status of the "Ignition Available Area" has been "All".
Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 2 indoor electrical key antenna assembly (steering column).
Bring the electrical key transmitter sub-assembly near the No. 3 indoor electrical key antenna assembly (rear floor) and perform a smart entry and start system check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Rear Floor)>REMOVAL)
Check that the customize status of the "Ignition Available Area" has been "All".
Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 3 indoor electrical key antenna assembly (rear floor).
As the effect of wave interference decreases by moving the electrical key transmitter sub-assembly close to the each indoor electrical key antenna assembly, it may be possible to check whether wave interference is the cause of the problem.
If the problem only occurs in specific places or at specific times, wave interference may be the cause of the problem. Also, the vehicle may be have the effects of wave interference with the parts installed by the dealer. As a result, when parts have been installed by the dealer, it may be necessary to remove those parts before inspecting the vehicle.
There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.
If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.
| Result | Proceed to |
|---|---|
| System cannot be operated | A |
| System can be operated | B |
A
B
Check the following antennas in the key diagnostic mode (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).
Check the No. 1 indoor electrical key antenna assembly (front floor).
| *a | Inspection Point |
When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.
Check the No. 2 indoor electrical key antenna assembly (steering column).
| *A | for LHD |
| *B | for RHD |
| *a | Inspection Point |
When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.
Check the No. 3 indoor electrical key antenna (rear floor):
| *a | Inspection Point |
When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.
If the buzzer sounds, it can be determined that the vehicle interior transmitters are operating normally.
It is possible to check which indoor electrical key antenna assembly (front floor, steering column or rear floor) is operating by the sounding of the buzzer.
If the buzzer does not sound for any indoor electrical key antenna assemblies, the certification ECU (smart key ECU assembly) circuit may have a malfunction.
Wireless door lock buzzer sounds.
| Result | Proceed to |
|---|---|
| Front floor operation check fails | A |
| Steering column operation check fails | B |
| Rear floor operation check fails | C |
| All operation checks are normal | D |
A
B
C
D
Disconnect the G51 No. 1 indoor electrical key antenna assembly (front floor) connector.
Disconnect the G79 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G51-1 (ANTE5) - G79-3 (CLG5) | Always | Below 1 Ω |
| G51-3 (CLGB) - G79-2 (CG5B) | Always | Below 1 Ω |
| G51-1 (ANTE5) or G79-3 (CLG5) - Body ground | Always | 10 kΩ or higher |
| G51-3 (CLGB) or G79-2 (CG5B) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the G51 No. 1 indoor electrical key antenna assembly (front floor) connector.
Connect the G79 certification ECU (smart key ECU assembly) connector.
Using an oscilloscope, check the waveform.
| Tester Connection | Switch Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| G51-1 (ANTE5) - G51-3 (CLGB) | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Door is open 4.
Door is closed 5.
Within 30 seconds |
2 V/DIV., 500 ms/DIV. | Pulse generation (See waveform) |
| *1 | Waveform |
| *a | Front view of wire harness connector
(to No. 1 Indoor Electrical Key Antenna [Front Floor]) |
| *b | Within approximately 30 seconds from when the door is closed |
| *c | After approximately 30 seconds from when the door is closed |
OK
NG
Temporarily replace the No. 1 indoor electrical key antenna assembly (front floor) with a new or known good one (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Front Side)>REMOVAL).
NEXT
Check the following antenna in the key diagnostic mode (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).
Check the No. 1 indoor electrical key antenna assembly (front floor).
When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.
Wireless door lock buzzer sounds.
| *a | Inspection Point |
OK
NG
Disconnect the G52 No. 2 indoor electrical key antenna assembly (steering column) connector.
Disconnect the G78 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G52-1 (ANTE6) - G78-11 (CLG6) | Always | Below 1 Ω |
| G52-3 (CLGB) - G78-10 (CG6B) | Always | Below 1 Ω |
| G52-1 (ANTE6) or G78-11 (CLG6) - Body ground | Always | 10 kΩ or higher |
| G52-3 (CLGB) or G78-10 (CG6B) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the G52 No. 2 indoor electrical key antenna assembly (steering column) connector.
Connect the G78 certification ECU (smart key ECU assembly) connector.
Using an oscilloscope, check the waveform.
| Tester Connection | Switch Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| G52-1 (ANTE6) - G52-3 (CLGB) | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Door is open 4.
Door is closed 5.
Within 30 seconds |
2 V/DIV., 500 ms/DIV. | Pulse generation (See waveform) |
| *1 | Waveform |
| *a | Front view of wire harness connector
(to No. 2 Indoor Electrical Key Antenna [Steering Column]) |
| *b | Within approximately 30 seconds from when the door is closed |
| *c | After approximately 30 seconds from when the door is closed |
OK
NG
Temporarily replace the No. 2 indoor electrical key antenna assembly (steering column) with a new or known good one (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Driver Side)>REMOVAL).
NEXT
Check the following antenna in the key diagnostic mode (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).
Check the No. 2 indoor electrical key antenna assembly (steering column).
When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.
Wireless door lock buzzer sounds.
| *A | for LHD |
| *B | for RHD |
| *a | Inspection Point |
OK
NG
Disconnect the M16 No. 3 indoor electrical key antenna assembly (rear floor) connector.
Disconnect the G78 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M16-1 (ANTE7) - G78-9 (CLG7) | Always | Below 1 Ω |
| M16-3 (CLGB) - G78-8 (CG7B) | Always | Below 1 Ω |
| M16-1 (ANTE7) or G78-9 (CLG7) - Body ground | Always | 10 kΩ or higher |
| M16-3 (CLGB) or G78-8 (CG7B) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the M16 No. 3 indoor electrical key antenna assembly (rear floor) connector.
Connect the G78 certification ECU (smart key ECU assembly) connector.
Using an oscilloscope, check the waveform.
| Tester Connection | Switch Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| M16-1 (ANTE7) - M16-3 (CLGB) | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Door is open 4.
Door is closed 5.
Within 30 seconds |
2 V/DIV., 500 ms/DIV. | Pulse generation (See waveform) |
| *1 | Waveform |
| *a | Front view of wire harness connector
(to No. 3 Indoor Electrical Key Antenna [Rear Floor]) |
| *b | Within approximately 30 seconds from when the door is closed |
| *c | After approximately 30 seconds from when the door is closed |
OK
NG
Temporarily replace the No. 3 indoor electrical key antenna assembly (rear floor) with a new or known good one (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Rear Floor)>REMOVAL).
NEXT
Check the following antenna in the key diagnostic mode (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).
Check the No. 3 indoor electrical key antenna assembly (rear floor).
When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.
Wireless door lock buzzer sounds.
| *a | Inspection Point |
OK
NG