Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Entry Function) › 2013.12–2014.12
RM2170E _58 Vehicle Interior _057035 THEFT DETERRENT / KEYLESS ENTRY _0278080 SMART ENTRY AND START SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  B27A1  Open in Driver Side Electrical Antenna Circuit  


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the front door outside handle assembly (for driver door) [electrical key antenna] at intervals of 0.25 seconds. For the front door outside handle assembly (for driver door) [electrical key antenna] to detect when the electrical key transmitter sub-assembly is brought close to the vehicle, a signal requesting a response from the electrical key transmitter sub-assembly is transmitted within approximately 1 m (3.28 ft.) of the driver door at intervals of 0.25 seconds. DTC B27A1 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door) [electrical key antenna] (between terminals CLG1 and ANT1, or terminals CG1B and ANT2).

DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B27A1 An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door) (CLG1 - ANT1, CG1B - ANT2) (This is detected by the malfunction detection circuit in the certification ECU (smart key ECU assembly)) (1 trip detection logic*).
·

Wire harness or connector

·

Front door outside handle assembly (for driver door)

·

Certification ECU (smart key ECU assembly)


Any time

*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Entry lock/unlock operation cannot be performed for driver door -

Related Data List and Active Test
DTC Code Data List and Active Test
B27A1 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

B349521E80
0.396,3.667 2.052,4.083 1.656,0.417 10 false Front Door Outside Handle Assembly (for Driver Door) 0.396,3.49 1.281,3.719 0.885,0.229 10 false J10*1 H10*2 5.396,3.5 6.948,4.01 1.552,0.51 10 false Certification ECU (Smart Key ECU Assembly) 1.313,0.729 1.854,0.938 0.542,0.208 10 false ANT1 1.302,1.198 1.844,1.406 0.542,0.208 10 false ANT2 1.552,1.667 2.094,1.875 0.542,0.208 10 false B 1.271,2.125 1.813,2.333 0.542,0.208 10 false SENS 1.302,2.583 1.844,2.792 0.542,0.208 10 false TRG+ 1.375,3.031 1.917,3.24 0.542,0.208 10 false GND 1.781,0.604 2.323,0.813 0.542,0.208 10 false 6 1.792,1.063 2.333,1.271 0.542,0.208 10 false 3 1.792,1.521 2.333,1.729 0.542,0.208 10 false 5 1.792,1.99 2.333,2.198 0.542,0.208 10 false 4 1.781,2.438 2.323,2.646 0.542,0.208 10 false 1 1.792,2.906 2.333,3.115 0.542,0.208 10 false 2 5.458,0.542 6,0.75 0.542,0.208 10 false 5 5.385,0.729 5.719,0.938 0.333,0.208 10 false G55 5.375,1.188 5.708,1.396 0.333,0.208 10 false G55 5.375,1.646 5.708,1.854 0.333,0.208 10 false G55 5.375,2.094 5.708,2.302 0.333,0.208 10 false G55 5.375,2.563 5.708,2.771 0.333,0.208 10 false G54 5.375,3.021 5.708,3.229 0.333,0.208 10 false G55 5.479,1 6.021,1.208 0.542,0.208 10 false 4 5.427,1.458 5.969,1.667 0.542,0.208 10 false 15 5.469,1.917 6.01,2.125 0.542,0.208 10 false 3 5.469,2.375 6.01,2.583 0.542,0.208 10 false 7 5.448,2.833 5.99,3.042 0.542,0.208 10 false 1 5.74,0.74 6.281,0.948 0.542,0.208 10 false CLG1 5.74,1.188 6.281,1.396 0.542,0.208 10 false CG1B 5.74,1.656 6.281,1.865 0.542,0.208 10 false POS1 5.74,2.115 6.281,2.323 0.542,0.208 10 false SEN1 5.74,2.583 6.281,2.792 0.542,0.208 10 false TSW1 5.75,3.031 6.292,3.24 0.542,0.208 10 false E 3.281,4 4.167,4.229 0.885,0.229 10 false *1: for LHD 3.292,4.323 4.177,4.552 0.885,0.229 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the intelligent tester with the power switch off to troubleshoot:

Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".

·

The front door outside handle assembly (for driver door) has an antenna coil between ANT1 and ANT2 terminals.



PROCEDURE

1.CHECK CONNECTOR CONNECTION
a.

Turn the power switch off.


b.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door).

OK:

Connectors are properly connected.




OK

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - FRONT DOOR OUTSIDE HANDLE)

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - FRONT DOOR OUTSIDE HANDLE)
a.

Disconnect the G54 and G55 certification ECU (smart key ECU assembly) connectors.


b.

Disconnect the J10*1 or H10*2 front door outside handle assembly (for driver door) connector.


c.

Measure the resistance according to the value(s) in the table below.

*1: for LHD

*2: for RHD


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
G55-5 (CLG1) - J10-6 (ANT1) Always Below 1 Ω
G55-4 (CG1B) - J10-3 (ANT2) Always Below 1 Ω
G55-1 (E) - Body ground Always Below 1 Ω
J10-2 (GND) - Body ground Always Below 1 Ω
G55-5 (CLG1) or J10-6 (ANT1) - Body ground Always 10 kΩ or higher
G55-4 (CG1B) or J10-3 (ANT2) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
G55-5 (CLG1) - H10-6 (ANT1) Always Below 1 Ω
G55-4 (CG1B) - H10-3 (ANT2) Always Below 1 Ω
G55-1 (E) - Body ground Always Below 1 Ω
H10-2 (GND) - Body ground Always Below 1 Ω
G55-5 (CLG1) or H10-6 (ANT1) - Body ground Always 10 kΩ or higher
G55-4 (CG1B) or H10-3 (ANT2) - Body ground Always 10 kΩ or higher




OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO DRIVER SIDE ELECTRICAL KEY ANTENNA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO DRIVER SIDE ELECTRICAL KEY ANTENNA)
a.

Connect the G54 and G55 certification ECU (smart key ECU assembly) connectors.

U183420E01
0.984,0.428 1.205,0.628 0.221,0.200 10 *a 1.223,2.803 1.444,3.003 0.221,0.200 10 *1 0.949,3.628 1.309,3.793 0.360,0.165 10 GND 3.836,3.628 4.195,3.793 0.360,0.165 10 GND 4.13,2.803 4.350,3.003 0.221,0.200 10 *2 5.799,1.799 5.931,1.963 0.132,0.163 10 E 4.584,1.917 4.986,2.080 0.401,0.163 10 CG1B 4.081,1.917 4.483,2.080 0.401,0.163 10 CLG1 2.234,0.613 2.528,0.775 0.295,0.163 10 G53 4.858,0.613 5.222,0.775 0.364,0.163 10 G55 4.536,1.302 4.296,1.893 false 5.592,1.29 5.817,1.755 false 4.649,1.318 4.828,1.877 false 3.665,0.622 3.960,0.785 0.295,0.163 10 G54

Text in Illustration
*1 Waveform 1 *2 Waveform 2
*a Component with harness connected
(Certification ECU (smart key ECU assembly))
- -


b.

Connect the J10*3 or H10*4 front door outside handle assembly (for driver door) connector.


c.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Switch Condition Tool Setting Specified Condition
G55-5 (CLG1) - G55-1 (E) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought inside detection area*1

6.

All doors locked through wireless operation


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform 1)
G55-5 (CLG1) - G55-1 (E) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought outside detection area*2

6.

All doors locked through wireless operation


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform 2)
G55-4 (CG1B) - G55-1 (E) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought outside detection area*2

6.

All doors locked through wireless operation


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform 2)


*1: For details about the areas that are inside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

*2: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

*3: for LHD

*4: for RHD




OK

4.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR)
a.

Temporarily replace the front door outside handle assembly (for driver door) with a new or known good one (See page Vehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY).



NEXT

5.CLEAR DTC
6.CHECK FOR DTC

OK

END (FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)