The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the front door outside handle assembly (for driver door) [electrical key antenna] at intervals of 0.25 seconds. For the front door outside handle assembly (for driver door) [electrical key antenna] to detect when the electrical key transmitter sub-assembly is brought close to the vehicle, a signal requesting a response from the electrical key transmitter sub-assembly is transmitted within approximately 1 m (3.28 ft.) of the driver door at intervals of 0.25 seconds. DTC B27A1 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door) [electrical key antenna] (between terminals CLG1 and ANT1, or terminals CG1B and ANT2).
| DTC Code | DTC Detection Condition | Trouble Area | DTC Output Confirmation Operation |
|---|---|---|---|
| B27A1 | An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door) (CLG1 - ANT1, CG1B - ANT2) (This is detected by the malfunction detection circuit in the certification ECU (smart key ECU assembly)) (1 trip detection logic*). | ·
Wire harness or connector ·
Front door outside handle assembly (for driver door) ·
Certification ECU (smart key ECU assembly) |
Any time |
*: Only output while a malfunction is present.
| Vehicle Condition when Malfunction Detected | Fail-safe Operation when Malfunction Detected |
|---|---|
| Entry lock/unlock operation cannot be performed for driver door | - |
| DTC Code | Data List and Active Test |
|---|---|
| B27A1 | Key diagnostic mode can be used to perform troubleshooting |
The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
When using the intelligent tester with the power switch off to troubleshoot:
Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.
Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).
After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".
The front door outside handle assembly (for driver door) has an antenna coil between ANT1 and ANT2 terminals.
Turn the power switch off.
Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door).
Connectors are properly connected.
OK
NG
Disconnect the G79 and G77 certification ECU (smart key ECU assembly) connectors.
Disconnect the J10*1 or H10*2 front door outside handle assembly (for driver door) connector.
Measure the resistance according to the value(s) in the table below.
*1: for LHD
*2: for RHD
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G79-12 (CLG1) - J10-6 (ANT1) | Always | Below 1 Ω |
| G79-13 (CG1B) - J10-3 (ANT2) | Always | Below 1 Ω |
| G77-11 (E) - Body ground | Always | Below 1 Ω |
| J10-2 (GND) - Body ground | Always | Below 1 Ω |
| G79-12 (CLG1) or J10-6 (ANT1) - Body ground | Always | 10 kΩ or higher |
| G79-13 (CG1B) or J10-3 (ANT2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G79-12 (CLG1) - H10-6 (ANT1) | Always | Below 1 Ω |
| G79-13 (CG1B) - H10-3 (ANT2) | Always | Below 1 Ω |
| G77-11 (E) - Body ground | Always | Below 1 Ω |
| H10-2 (GND) - Body ground | Always | Below 1 Ω |
| G79-12 (CLG1) or H10-6 (ANT1) - Body ground | Always | 10 kΩ or higher |
| G79-13 (CG1B) or H10-3 (ANT2) - Body ground | Always | 10 kΩ or higher |
OK
NG
Connect the G79 and G77 certification ECU (smart key ECU assembly) connectors.
| *1 | Waveform 1 | *2 | Waveform 2 |
| *a | Component with harness connected
(Certification ECU (smart key ECU assembly)) |
- | - |
Connect the J10*3 or H10*4 front door outside handle assembly (for driver door) connector.
Using an oscilloscope, check the waveform.
| Tester Connection | Switch Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| G79-12 (CLG1) - G77-11 (E) | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Electrical key transmitter sub-assembly not inside vehicle 5.
Electrical key transmitter sub-assembly brought inside detection area*1 6.
All doors locked through wireless operation |
2 V/DIV., 500 ms/DIV. | Pulse generation (See waveform 1) |
| G79-12 (CLG1) - G77-11 (E) | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Electrical key transmitter sub-assembly not inside vehicle 5.
Electrical key transmitter sub-assembly brought outside detection area*2 6.
All doors locked through wireless operation |
2 V/DIV., 500 ms/DIV. | Pulse generation (See waveform 2) |
| G79-13 (CG1B) - G77-11 (E) | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Electrical key transmitter sub-assembly not inside vehicle 5.
Electrical key transmitter sub-assembly brought outside detection area*2 6.
All doors locked through wireless operation |
2 V/DIV., 500 ms/DIV. | Pulse generation (See waveform 2) |
*1: For details about the areas that are inside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).
*2: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).
*3: for LHD
*4: for RHD
OK
NG
Temporarily replace the front door outside handle assembly (for driver door) with a new or known good one (See page Vehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY).
NEXT
NEXT
Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>DTC CHECK / CLEAR).
DTC B27A1 is not output.
OK
NG