Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Start Function) › 2011.12–2013.12
RM2170E _58 Vehicle Interior _057035 THEFT DETERRENT / KEYLESS ENTRY _0278081 SMART ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  B2274  ACC Monitor Malfunction  


DESCRIPTION

This DTC is stored when a malfunction in the ACC output circuit is detected. The ACC output circuit is the circuit that goes from the ACC output terminal of the power management control ECU to the ACC relay.

HINT:

When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2274 Malfunction in the ACC relay circuit in the power management control ECU or in the external circuit (1-trip detection logic*).
HINT:

When the voltage at terminal ACCD is not at the standard, the system is determined to be malfunctioning.


·

AM2 fuse

·

ACC relay (Instrument panel junction block assembly)

·

Power management control ECU

·

Wire harness or connector


Wait 10 seconds after turning the power switch on (ACC) or on (IG), and then wait another 10 seconds after turning the power switch off.

*: Only detected while a malfunction is present.


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
·

If there is a malfunction due to the relay being stuck on, the ACC relay does not turn off even though the power switch is off.

·

If there is a malfunction due to the relay being stuck off, the ACC relay does not turn on even though the power switch is on (ACC).


HINT:

The power switch can be turned on (IG) and the hybrid control system can be started.


-

WIRING DIAGRAM

B309630E01
3.449,1.142 3.546,1.298 0.097,0.156 10 1 2.9,1.335 3.330,1.491 0.430,0.156 10 ACCD 5.092,1.65 5.415,1.806 0.324,0.156 10 ACC 2.201,3.023 3.474,3.386 1.273,0.363 10 Power Management Control ECU 3.917,2.243 6.604,2.399 2.687,0.156 10 Instrument Panel Junction Block Assembly 3.36,1.335 3.703,1.505 0.343,0.170 10 G58 3.926,1.335 4.122,1.501 0.196,0.165 10 3B 4.206,3.031 4.916,3.196 0.710,0.165 10 *1: for LHD 4.206,3.353 4.947,3.518 0.741,0.165 10 *2: for RHD 3.938,1.164 4.180,1.329 0.242,0.165 10 37 3.909,0.6 4.139,0.765 0.230,0.165 10 1*1 5.919,0.916 6.292,1.128 0.373,0.211 10 ACC 6.427,0.613 6.669,0.778 0.242,0.165 10 29 6.396,0.782 6.716,0.947 0.319,0.165 10 MB 6.473,1.161 6.715,1.326 0.242,0.165 10 8 6.427,1.341 6.650,1.506 0.223,0.165 10 3B 3.926,0.777 4.161,0.943 0.235,0.165 10 3E 4.231,0.6 4.461,0.765 0.230,0.165 10 1*2 4.248,0.777 4.484,0.943 0.235,0.165 10 3F 2.407,1.587 2.806,1.736 0.399,0.149 10 E01 2.139,1.401 2.249,1.546 0.111,0.145 10 5 2.053,1.587 2.341,1.778 0.288,0.191 10 G57 2.407,2.112 2.806,2.261 0.399,0.149 10 E02 2.146,1.919 2.256,2.065 0.111,0.145 10 5 2.053,2.112 2.341,2.302 0.288,0.191 10 G58 2.407,2.629 2.806,2.778 0.399,0.149 10 E1 2.137,2.436 2.247,2.582 0.111,0.145 10 6 2.053,2.629 2.341,2.819 0.288,0.191 10 G57 0.114,0.526 0.974,1.000 0.860,0.474 10 from Auxiliary Battery 1.317,0.679 1.647,0.869 0.330,0.191 10 AM2 2.407,0.543 2.806,0.692 0.399,0.149 10 AM21 2.139,0.358 2.249,0.504 0.111,0.145 10 7 2.053,0.543 2.333,0.733 0.280,0.191 10 G58 2.407,1.064 2.806,1.213 0.399,0.149 10 AM22 2.139,0.87 2.249,1.015 0.111,0.145 10 1 2.053,1.064 2.341,1.255 0.288,0.191 10 G57

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus:

for Power Source Control: Body / Power Source Control / DTC.

for Entry&Start: Body / Entry&Start / DTC.

·

The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Before replacing the power management control ECU, refer to the Service Bulletin.

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



HINT:
Related Data List and Active Test Items
DTC Data List Item Active Test Item
B2274
Power Source Control
·

ACC Relay Monitor


-


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

2.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS ORCONNECTOR IN CIRCUIT CONNECTED TOPOWER SOURCE

2.CHECK HARNESS AND CONNECTOR (GROUND)

OK

3.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the G58 connector from the power management control ECU.


b.

Disconnect the 3B connector from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G58-1 (ACCD) - 3B-37 Always Below 1 Ω
3B-8 - Body ground Always Below 1 Ω
G58-1 (ACCD) or 3B-37 - Body ground Always 10 kΩ or higher




OK

4.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC RELAY)
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).

U183676E02
5.146,0.198 5.469,0.365 0.323,0.167 10 false 3E 5.469,0.198 5.625,0.365 0.156,0.167 10 false *1 5.771,0.188 6.094,0.354 0.323,0.167 10 false 3F 6.073,0.188 6.229,0.354 0.156,0.167 10 false *2 1.938,0.188 2.26,0.354 0.323,0.167 10 false 3B 3.75,1.573 4.073,1.74 0.323,0.167 10 false MB 0.177,0.073 0.5,0.24 0.323,0.167 10 false *a

Text in Illustration
*1 for LHD *2 for RHD
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3E-1 - MB-29*1
3F-1 - MB-29*2
Auxiliary battery voltage not applied to terminals 3B-37 and 3B-8 10 kΩ or higher
Auxiliary battery voltage applied to terminals 3B-37 and 3B-8 Below 1 Ω


*1: for LHD

*2: for RHD




OK

5.INSPECT POWER MANAGEMENT CONTROL ECU

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

5.INSPECT POWER MANAGEMENT CONTROL ECU
U183360E01
0.057,0.047 0.210,0.183 0.153,0.136 10 *a 2.516,0.453 2.797,0.592 0.281,0.139 10 G58 2.528,1.893 2.939,2.032 0.411,0.139 10 ACCD 2.733,1.902 2.848,1.133 false

a.

Reconnect the G58 power management control ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G58-1 (ACCD) - Body ground Power switch off → Power switch on (ACC) 1 V or less → 8.5 V or higher


Text in Illustration
*a Component with harness connected
(Power Management Control ECU)



OK

NG