Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Start Function) › from 2015.11
RM2170E _58 Vehicle Interior _057035 THEFT DETERRENT / KEYLESS ENTRY _0278081 SMART ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  B2282  Vehicle Speed Signal Malfunction  B2283  Vehicle Speed Sensor Malfunction  


DESCRIPTION

DTC B2282 is stored when the vehicle speed signal sent by the combination meter assembly via direct line and the vehicle speed signal sent via CAN communication do not match.

DTC B2283 is stored when a malfunction in the vehicle speed sensor is detected.

HINT:

When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2282 The vehicle speed signal sent by the combination meter assembly via direct line and the vehicle speed signal sent via CAN communication (1-trip detection logic*) do not match.
·

AM2 fuse

·

Meter/gauge system

·

Certification ECU (Smart key ECU assembly)

·

Junction Connector

·

Wire harness or connector


Drive the vehicle for 20 seconds at a vehicle speed of 25 km/h (16 mph) or more, and then drive the vehicle at a vehicle speed of less than 5 km/h (3 mph) for 20 seconds.
B2283 Vehicle speed signal malfunction detection : Excessive deceleration is detected (1-trip detection logic*)
·

AM2 fuse

·

Meter/gauge system

·

Certification ECU (Smart key ECU assembly)

·

Junction Connector

·

Wire harness or connector


Drive the vehicle for 30 seconds or more at a vehicle speed of 50 km/h (31 mph) or more.

*: Only detected while a malfunction is present and the power switch is on (IG)


Vehicle Condition and Fail-safe Function when Malfunction Detected
DTC Code Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
B2282
·

When the signal from the direct line or CAN communication is malfunctioning and indicates that the vehicle speed is 0 km/h (0 mph), there is no effect on vehicle behavior.

·

When the signal from the direct line or CAN communication is malfunctioning and indicates that the vehicle is moving, the power switch cannot be turned from on (IG) to off.


-
B2283
·

The power source mode is changed to off (the hybrid control system is stopped) by pressing the power switch while the vehicle is being driven.

·

With the electrical key transmitter sub-assembly in the cabin, even if a hybrid control system start operation is performed, the hybrid control system does not start.


Steering lock operation is prohibited.

WIRING DIAGRAM

B438369E02
1.948,2.844 2.344,3 0.396,0.156 10 false SPD 2.396,2.802 2.573,2.958 0.177,0.156 10 false 27 2.052,2.083 2.281,2.229 0.229,0.146 10 false +B 2.448,1.885 2.563,2.031 0.115,0.146 10 false 2 2.354,2.104 2.646,2.292 0.292,0.188 10 false G77 0.865,2.531 1.135,2.677 0.271,0.146 10 false E 0.583,2.333 0.76,2.479 0.177,0.146 10 false 11 0.521,2.552 0.823,2.74 0.302,0.188 10 false G77 2.344,3.01 2.635,3.198 0.292,0.188 10 false G79 0.177,1.438 1.302,1.583 1.125,0.146 10 false Skid Control ECU 0.854,0.438 1.146,0.583 0.292,0.146 10 false SP1 0.198,1.281 0.521,1.458 0.323,0.177 10 false A41 1.219,0.438 1.406,0.583 0.188,0.146 10 false 11 3.146,2.813 3.323,2.969 0.177,0.156 10 false 37 4.281,2.813 4.458,2.969 0.177,0.156 10 false 15 4.281,4.719 4.458,4.875 0.177,0.156 10 false 16 4.302,6.385 4.49,6.542 0.188,0.156 10 false 38 3.146,4.719 3.323,4.875 0.177,0.156 10 false 40 3.146,4.917 3.479,5.073 0.333,0.156 10 false 3C 3.146,3 3.479,3.156 0.333,0.156 10 false 3A 4.281,3 4.615,3.156 0.333,0.156 10 false 3B 4.281,4.927 4.615,5.083 0.333,0.156 10 false 3A 4.292,6.583 4.625,6.74 0.333,0.156 10 false 3A 5.333,0.427 5.635,0.573 0.302,0.146 10 false 40 5.323,2.885 5.594,3.031 0.271,0.146 10 false 39 5.583,0.51 5.781,0.656 0.198,0.146 10 false SI 5.583,3 5.781,3.146 0.198,0.146 10 false +S 5.667,3.354 5.938,3.5 0.271,0.146 10 false G1 5.667,3.5 6.875,3.802 1.208,0.302 10 false Combination Meter Assembly 5.604,4.813 5.927,4.958 0.323,0.146 10 false SPD 5.333,4.813 5.646,4.979 0.313,0.167 10 false 17 5.656,5.229 5.99,5.385 0.333,0.156 10 false G41 5.656,5.375 6.677,5.708 1.021,0.333 10 false Radio Receiver Assembly*1 3.208,6.865 4.427,7.031 1.219,0.167 10 false Junction Connector 2.073,4.813 2.385,4.979 0.313,0.167 10 false 16 0.906,5.24 1.5,5.396 0.594,0.156 10 false A34 0.906,5.385 2.219,5.708 1.313,0.323 10 false Headlight Leveling ECU Assembly*3 1.615,4.813 2.094,4.958 0.479,0.146 10 false SPDR 3.906,2.094 5.25,2.26 1.344,0.167 10 false from Auxiliary Battery 3.083,2.25 3.417,2.438 0.333,0.188 10 false AM2 2.823,1.042 4.604,1.24 1.781,0.198 10 false CAN Communication Line 0.792,3.385 2.438,3.938 1.646,0.552 10 false Certification ECU (Smart Key ECU Assembly) 0.094,6.458 2.427,6.635 2.333,0.177 10 false *1: w/ Audio and Visual System 0.094,7.271 1.531,7.448 1.438,0.177 10 false *3: for LED Headlight 5.615,6.469 5.938,6.615 0.323,0.146 10 false SPD 5.406,6.469 5.719,6.635 0.313,0.167 10 false 6 5.188,6.74 5.521,6.896 0.333,0.156 10 false G85 5.188,6.896 7.063,7.302 1.875,0.406 10 false Vehicle Approaching Speaker Controller*2 0.094,6.865 2.844,7.052 2.75,0.188 10 false *2: w/ Vehicle Proximity Notification System

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter. The signal is changed to a pulse signal at the transistor in the combination meter. Each ECU controls the respective system based on the pulse signal.

·

If a short occurs in an ECU, all systems in the diagram above will not operate normally.



CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus:

for Power Source Control: Body / Power Source Control / DTC.

for Entry&Start: Body / Entry&Start / DTC.

·

The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



HINT:
Related Data List and Active Test Items
DTC Data List Item Active Test Item
B2282
B2283
Power Source Control
·

Vehicle Speed Signal

·

Engine Condition

·

Power Supply Condition


Combination Meter
·

Vehicle Speed Meter


-


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Combination Meter / Data List.


e.

Check the Data List for proper functioning of the vehicle speed signal.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Vehicle Speed Meter Vehicle speed/Min.: 0, Max.: 255 Almost same as actual vehicle speed (Speedometer tester) -

OK:

Vehicle speed displayed on the intelligent tester is almost the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).




OK

2.READ VALUE USING INTELLIGENT TESTER

NG

GO TO METER / GAUGE SYSTEM (Speedometer Malfunction)

2.READ VALUE USING INTELLIGENT TESTER
a.

Enter the following menus: Body / Power Source Control / Data List.


b.

Read the Data List according to the display on the intelligent tester.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Vehicle speed signal Vehicle being driven or stopped/Stop or Run Stop: Vehicle stopped
Run: Vehicle being driven at 5 km/h (3 mph) or more
-

OK:

Stop (vehicle is stopped) and Run (vehicle is running) appear on the screen.




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

4.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

4.CHECK HARNESS AND CONNECTOR (GROUND)

OK

5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - COMBINATION METER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - COMBINATION METER ASSEMBLY)
a.

Disconnect the G79 connector from the certification ECU (smart key ECU assembly).


b.

Disconnect the G1 connector from the combination meter assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G79-27 (SPD) - G1-39 (+S) Always Below 1 Ω
G79-27 (SPD) or G1-39 (+S) - Body ground Always 10 kΩ or higher




OK

6.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - JUNCTION CONNECTOR)
6.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the G79 certification ECU (smart key ECU assembly) connector.

U183497E02
2.698,1.198 2.521,1.844 false 4.677,1.219 4.802,1.844 false 0.073,0 0.302,0.229 0.229,0.229 10 false *a 4.458,2.823 4.896,3.052 0.438,0.229 10 false GND 2.458,1.875 2.896,2.104 0.438,0.229 10 false E 4.708,1.854 5.146,2.083 0.438,0.229 10 false SPD 2.156,0.323 2.49,0.552 0.333,0.229 10 false G77 4.802,0.323 5.135,0.552 0.333,0.229 10 false G79


b.

Reconnect the G1 combination meter assembly connector.


c.

Connect an oscilloscope to terminal G79-27 (SPD) and G77-11 (E).


d.

Turn the power switch on (IG).


e.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tester Connection G79-27 (SPD) - G77-11 (E)
Tool setting 5 V/DIV., 100 ms./DIV.
Vehicle condition Power switch on (READY), vehicle being driven at approx. 5 km/h (3 mph)

OK:

The waveform is similar to that shown in the illustration.


HINT:

The wavelength becomes shorter as the vehicle speed increases.



Text in Illustration
*a Component with harness connected
Certification ECU (Smart Key ECU Assembly)


OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

GO TO METER / GAUGE SYSTEM (Speed Signal Circuit)

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - JUNCTION CONNECTOR)
a.

Disconnect the 3B junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G1-39 (+S) - 3B-15 Always Below 1 Ω
G1-39 (+S) or 3B-15 - Body ground Always 10 kΩ or higher




OK

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - JUNCTION CONNECTOR)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G79-27 (SPD) - 3A-37 Always Below 1 Ω
G79-27 (SPD) or 3A-37 - Body ground Always 10 kΩ or higher




OK

REPLACE JUNCTION CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR