Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Start Function) › from 2014.12
RM2170E _58 Vehicle Interior _057035 THEFT DETERRENT / KEYLESS ENTRY _0278081 SMART ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (ACC)  


DESCRIPTION

If the power switch is pressed with the electrical key transmitter sub-assembly in the cabin, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode.

HINT:

When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


WIRING DIAGRAM

B392457E02
3.449,1.142 3.546,1.298 0.097,0.156 10 4 2.9,1.335 3.330,1.491 0.430,0.156 10 ACCD 5.092,1.65 5.415,1.806 0.324,0.156 10 ACC 2.266,2.257 3.539,2.829 1.273,0.572 10 Certification ECU (Smart Key ECU Assembly) 3.917,2.243 6.604,2.399 2.687,0.156 10 Instrument Panel Junction Block Assembly 3.36,1.335 3.703,1.505 0.343,0.170 10 G79 3.926,1.335 4.122,1.501 0.196,0.165 10 3B 0.255,3.395 0.965,3.560 0.710,0.165 10 *1: for LHD 1.18,3.409 1.921,3.574 0.741,0.165 10 *2: for RHD 3.938,1.164 4.180,1.329 0.242,0.165 10 37 3.909,0.6 4.139,0.765 0.230,0.165 10 1*1 5.919,0.916 6.292,1.128 0.373,0.211 10 ACC 6.427,0.613 6.669,0.778 0.242,0.165 10 13 6.396,0.782 6.716,0.947 0.319,0.165 10 3B 6.473,1.161 6.715,1.326 0.242,0.165 10 8 6.427,1.341 6.650,1.506 0.223,0.165 10 3B 3.926,0.777 4.161,0.943 0.235,0.165 10 3E 4.231,0.6 4.461,0.765 0.230,0.165 10 1*2 4.248,0.777 4.484,0.943 0.235,0.165 10 3F 2.407,1.693 2.806,1.842 0.399,0.149 10 E 2.086,1.501 2.297,1.647 0.211,0.146 10 11 2.047,1.693 2.335,1.884 0.288,0.191 10 G77 0.114,0.526 0.974,1.000 0.860,0.474 10 from Auxiliary Battery 1.317,0.679 1.647,0.869 0.330,0.191 10 AM2 2.407,0.543 2.806,0.692 0.399,0.149 10 +B 2.139,0.358 2.249,0.504 0.111,0.145 10 2 2.053,0.543 2.333,0.733 0.280,0.191 10 G77

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus:

for Power Source Control: Body / Power Source Control / DTC.

for Entry&Start: Body / Entry&Start / DTC.

·

The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>DIAGNOSTIC TROUBLE CODE CHART).

·

If the smart entry and start system is disabled through the customize function, enable the system before performing troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>CUSTOMIZE PARAMETERS).

·

Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After completing repairs, confirm that the problem does not occur.



HINT:
Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Power source mode does not change to on (ACC) but does change to on (IG)
Power Source Control
·

Power Supply Condition

·

ACC Relay Monitor


-


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

OK

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

OK

3.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

3.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

OK

CHECK RELAY CONTACT SIDE CIRCUIT

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)