Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Start Function) › 2013.12–2014.12
RM2170E _58 Vehicle Interior _057035 THEFT DETERRENT / KEYLESS ENTRY _0278081 SMART ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  B2286  Runnable Signal Malfunction  


DESCRIPTION

This DTC is stored when a malfunction is detected in the READY signal circuit inside the power management control ECU.

HINT:

When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2286 READY signal error inside the power management control ECU (1-trip detection logic*)
·

AM2 fuse

·

Power management control ECU

·

Wire harness or connector


Turn the power switch on (IG) and wait 20 seconds or more.

*: Only detected while a malfunction is present and the power switch is on (IG)


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The power source mode does not change to on (READY). -

WIRING DIAGRAM

B296562E12
2.729,0.719 3.063,0.896 0.333,0.177 10 false AM2 4.073,2.073 5.354,2.479 1.281,0.406 10 false Power Management Control ECU 4.865,0.563 5.302,0.708 0.438,0.146 10 false E01 5.281,0.375 5.396,0.521 0.115,0.146 10 false 5 5.198,0.563 5.49,0.75 0.292,0.188 10 false G57 4.865,1.115 5.302,1.26 0.438,0.146 10 false E02 5.302,0.938 5.417,1.083 0.115,0.146 10 false 5 5.198,1.115 5.49,1.302 0.292,0.188 10 false G58 4.938,1.667 5.375,1.813 0.438,0.146 10 false E1 5.281,1.469 5.396,1.615 0.115,0.146 10 false 6 5.198,1.656 5.49,1.844 0.292,0.188 10 false G57 1.344,0.563 2.25,0.875 0.906,0.313 10 false from Auxiliary Battery 4.24,0.573 4.677,0.719 0.438,0.146 10 false AM21 3.979,0.375 4.094,0.521 0.115,0.146 10 false 7 3.865,0.563 4.156,0.75 0.292,0.188 10 false G58 4.24,1.115 4.677,1.26 0.438,0.146 10 false AM22 3.958,0.927 4.073,1.073 0.115,0.146 10 false 1 3.865,1.115 4.146,1.302 0.281,0.188 10 false G57

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus:

for Power Source Control: Body / Power Source Control / DTC.

for Entry&Start: Body / Entry&Start / DTC.

·

The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Before replacing the power management control ECU, refer to the Service Bulletin.

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



HINT:
Related Data List and Active Test Items
DTC Data List Item Active Test Item
B2286
Power Source Control
·

Ready Signal


-


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

2.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

2.CHECK HARNESS AND CONNECTOR (GROUND)

OK

3.CHECK FOR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK FOR DTC

b.

Turn the power switch on (IG).


c.

After 25 seconds have elapsed, check if the DTC has been output again.

OK:

DTC B2286 is not output




OK

NG