Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › 2011.12–2014.12
RM2170E _58 Vehicle Interior _057035 THEFT DETERRENT / KEYLESS ENTRY _0278082 ENGINE IMMOBILISER SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  B2784  Antenna Coil Open / Short  


DESCRIPTION

When an open or short circuit is detected in the transponder key amplifier coil built into the power switch, the certification ECU (smart key ECU assembly) stores this DTC. This DTC is also stored as a past DTC.

DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2784 The transponder key amplifier coil built into the power switch is open (see below) or shorted (determined by communication with certification ECU (smart key ECU assembly)) (1 trip detection logic*).
·

Terminal AGND, VC5, TXCT or CODE is open (includes disconnection of the power switch).

·

The transponder key amplifier coil built into the power switch is open.


·

Power switch

·

Wire harness or connector

·

Certification ECU (smart key ECU assembly)


With the shift lever in P, the key held near the power switch and a hybrid control system start operation is performed by pressing and holding the power switch when the key battery is depleted.

*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Hybrid control system cannot be started when key battery is depleted by holding key near power switch and pressing and holding power switch with shift lever in P -

Related Data List and Active Test
DTC Code Data List and Active Test
B2784 -

WIRING DIAGRAM

B278927E12
5.073,2.813 6.646,3.156 1.573,0.344 10 false Certification ECU (Smart Key ECU Assembly) 0.896,2.979 1.802,3.125 0.906,0.146 10 false Power Switch 0.885,2.813 1.354,3.042 0.469,0.229 10 false G48 4.948,0.74 5.292,0.969 0.344,0.229 10 false G54 5.052,0.552 5.156,0.698 0.104,0.146 10 false 9 1.927,0.625 2.115,0.771 0.188,0.146 10 false 10 1.938,1.146 2.052,1.292 0.115,0.146 10 false 7 1.948,1.667 2.063,1.813 0.115,0.146 10 false 8 1.948,2.177 2.063,2.323 0.115,0.146 10 false 6 5.052,1.083 5.156,1.229 0.104,0.146 10 false 3 5.052,2.115 5.156,2.26 0.104,0.146 10 false 6 5.01,1.594 5.198,1.74 0.188,0.146 10 false 13 5.292,0.719 5.594,0.865 0.302,0.146 10 false VC5 1.552,0.74 1.854,0.885 0.302,0.146 10 false VC5 5.292,1.24 5.688,1.385 0.396,0.146 10 false TXCT 1.51,1.26 1.906,1.406 0.396,0.146 10 false TXCT 5.292,1.75 5.719,1.896 0.427,0.146 10 false CODE 1.448,1.781 1.875,1.927 0.427,0.146 10 false CODE 5.292,2.271 5.719,2.417 0.427,0.146 10 false AGND 1.458,2.292 1.885,2.438 0.427,0.146 10 false AGND 4.958,1.26 5.344,1.531 0.385,0.271 10 false G54 4.958,1.771 5.313,2.01 0.354,0.24 10 false G54 4.958,2.292 5.375,2.469 0.417,0.177 10 false G55

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - POWER SWITCH)
a.

Disconnect the G55 and G54 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the G48 power switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G54-13 (CODE) - G48-8 (CODE) Always Below 1 Ω
G54-3 (TXCT) - G48-7 (TXCT) Always Below 1 Ω
G54-9 (VC5) - G48-10 (VC5) Always Below 1 Ω
G55-6 (AGND) - G48-6 (AGND) Always Below 1 Ω
G48-8 (CODE) - Body ground Always 10 kΩ or higher
G48-7 (TXCT) - Body ground Always 10 kΩ or higher
G48-10 (VC5) - Body ground Always 10 kΩ or higher
G48-6 (AGND) - Body ground Always 10 kΩ or higher




OK

2.REPLACE POWER SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REPLACE POWER SWITCH
a.

Temporarily replace the power switch with a new or known good one (See page Engine / Hybrid System>1NZ-FXE STARTING>POWER SWITCH>REMOVAL).



NEXT

3.CLEAR DTC
3.CLEAR DTC

NEXT

4.CHECK DTC OUTPUT
4.CHECK DTC OUTPUT
a.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR).

HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B2784 is not output.




OK

END (POWER SWITCH WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)