Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › 2011.12–2014.12
RM2170E _58 Vehicle Interior _057035 THEFT DETERRENT / KEYLESS ENTRY _0278082 ENGINE IMMOBILISER SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  B278A  Short to GND in Immobiliser System Power Source Circuit  


DESCRIPTION

When there is a short to GND in the power supply for the transponder key amplifier of the power switch, the certification ECU (smart key ECU assembly) stores this DTC.

DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B278A A short to GND in the power supply of the transponder key amplifier of the power switch (VC5 - VC5) (1 trip detection logic*).
·

Wire harness or connector


·

Power switch


·

Certification ECU (smart key ECU assembly)


With the shift lever in P, the key held near the power switch and a hybrid control system start operation is performed by pressing and holding the power switch when the key battery is depleted.

*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Hybrid control system cannot be started when key battery is depleted by holding key near power switch and pressing and holding power switch with shift lever in P -

Related Data List and Active Test
DTC Code Data List and Active Test
B278A -

WIRING DIAGRAM

B278928E09
5.073,2.823 6.604,3.271 1.531,0.448 10 false Certification ECU (Smart Key ECU Assembly) 0.906,2.958 2.01,3.24 1.104,0.281 10 false Power Switch 0.896,2.813 1.406,3.125 0.51,0.313 10 false G48 4.958,1.167 5.313,1.427 0.354,0.26 10 false G54 5.052,0.99 5.167,1.135 0.115,0.146 10 false 9 5.052,1.906 5.167,2.052 0.115,0.146 10 false 6 1.958,1.979 2.073,2.125 0.115,0.146 10 false 6 1.958,1.052 2.292,1.385 0.333,0.333 10 false 10 5.302,1.167 5.615,1.313 0.313,0.146 10 false VC5 1.563,1.177 2.063,1.5 0.5,0.323 10 false VC5 5.302,2.094 5.719,2.24 0.417,0.146 10 false AGND 1.458,2.094 2.125,2.417 0.667,0.323 10 false AGND 4.958,2.083 5.333,2.281 0.375,0.198 10 false G55

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - POWER SWITCH)
a.

Disconnect the G55 and G54 certification ECU (smart key ECU assembly) connectors.


b.

Disconnect the G48 power switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G54-9 (VC5) - G48-10 (VC5) Always Below 1 Ω
G55-6 (AGND) - G48-6 (AGND) Always Below 1 Ω
G48-10 (VC5) - Body ground Always 10 kΩ or higher
G48-6 (AGND) - Body ground Always 10 kΩ or higher




OK

2.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the G55 and G54 certification ECU (smart key ECU assembly) connectors.


b.

Reconnect the G48 power switch connector.


c.
U159187E02
1.823,1.677 2.396,2.063 false 1.208,1.656 0.635,2.052 false 1.406,0.26 1.729,0.448 0.323,0.188 10 false G48 0.125,0.021 0.323,0.208 0.198,0.188 10 false *a 2.958,3.271 3.292,3.49 0.333,0.219 10 false GND 0.333,2.01 0.667,2.167 0.333,0.156 10 false VC5 2.469,2.031 2.896,2.188 0.427,0.156 10 false AGND

Using an oscilloscope, check the waveform.

HINT:

Perform this inspection on the power switch side.


Measurement Condition
Item Content
Tester Connection G48-10 (VC5) - G48-6 (AGND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Power switch off, key not in cabin, within 30 seconds after power switch pressed

OK:

Waveform is output normally (refer to illustration).


Text in Illustration
*a Component with harness connected
(Power Switch)



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)