Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM2170E _58 Vehicle Interior _057036 LIGHTING (INT) _0278087 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Front Door Courtesy Switch Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) detects the condition of the front door courtesy light switch using this circuit.

WIRING DIAGRAM

E235090E25
1.01,1.094 1.25,1.25 0.24,0.156 10 false M1 4.458,0.885 4.833,1.135 0.375,0.25 10 false 3D 4.458,0.688 4.698,0.854 0.24,0.167 10 false 36 5.646,0.875 6.01,1.083 0.365,0.208 10 false MB 6.031,0.885 6.604,1.115 0.573,0.229 10 false FLCY 5.708,0.688 5.948,0.854 0.24,0.167 10 false 2 5.615,2.125 6,2.302 0.385,0.177 10 false G59 6.01,2.146 6.74,2.479 0.729,0.333 10 false FRCY 5.667,1.927 5.906,2.094 0.24,0.167 10 false 19 3.167,0.781 3.406,0.948 0.24,0.167 10 false 1 3.167,2.042 3.406,2.208 0.24,0.167 10 false 1 1.01,1.26 4.198,1.542 3.188,0.281 10 false Front Door Courtesy Light Switch Assembly LH 1.115,2.375 1.427,2.531 0.313,0.156 10 false M2 1.115,2.531 4.188,2.833 3.073,0.302 10 false Front Door Courtesy Light Switch Assembly RH 4.219,1.396 5.833,1.823 1.615,0.427 10 false Instrument Panel Junction Block Assembly 5.406,2.833 7.052,3.406 1.646,0.573 10 false Main Body ECU (Multiplex Network Body ECU)

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the display on the intelligent tester.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FR Door Courtesy Front door courtesy light switch RH signal/OPEN or CLOSE OPEN: Front door RH open
CLOSE: Front door RH closed
-
FL Door Courtesy Front door courtesy light switch LH signal/OPEN or CLOSE OPEN: Front door LH open
CLOSE: Front door LH closed
-

OK:

Normal conditions listed above are displayed.


Result:
Result Proceed to
OK A
Front door courtesy light switch LH or RH does not operate B




A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (LH OR RH)
2.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (LH OR RH)
a.

Remove the front door courtesy light switch assembly (See page Vehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>REMOVAL).


b.

Inspect the front door courtesy light switch assembly (See page Vehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>INSPECTION).

OK:

Front door courtesy light switch assembly is normal.



Result:
Result Proceed to
OK (for Front LH) A
OK (for Front RH) B
NG C



A

3.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

B

5.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

C

REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3D instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M1-1 - 3D-36 Always Below 1 Ω
M1-1 - Body ground Always 10 kΩ or higher




OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

U159630E01
0.163,0.094 0.318,0.232 0.156,0.139 10 *a 1.311,0.29 1.509,0.429 0.198,0.139 10 3D 3.322,1.294 3.701,1.432 0.378,0.139 10 FLCY 4.678,0.29 4.992,0.447 0.314,0.157 10 MB 3.165,1.046 3.165,1.363 3.165,1.363 3.292,1.363 false

Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
3D-36 - MB-2 (FLCY) Always Below 1 Ω




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the G59 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M2-1 - G59-19 (FRCY) Always Below 1 Ω
M2-1 - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR