Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM › from 2014.12
RM2170E _58 Vehicle Interior _057036 LIGHTING (INT) _0278087 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  IG Signal Circuit  


DESCRIPTION

This circuit detects the power switch on (IG) or off condition, and sends it to the main body ECU (multiplex network body ECU).

WIRING DIAGRAM

E245103E05
5.646,3.417 6.885,4.104 1.24,0.688 10 false Main Body ECU (Multiplex Network Body ECU) 4.854,0.979 5.542,1.302 0.688,0.323 10 false ECU-IG NO. 1 3.938,1.521 4.635,1.792 0.698,0.271 10 false IG1 NO. 1 0.125,0.813 1.885,1.177 1.76,0.365 10 false from Auxiliary Battery 2.052,0.969 2.667,1.188 0.615,0.219 10 false DC/DC 2.823,3.094 5.469,3.271 2.646,0.177 10 false Instrument Panel Junction Block Assembly 1.021,4.083 2,4.281 0.979,0.198 10 false *1: for LHD 2.24,4.083 3.427,4.292 1.188,0.208 10 false *2: for RHD 5.729,2.063 5.906,2.24 0.177,0.177 10 false 32 2.865,0.844 3.208,1.021 0.344,0.177 10 false 3E*1 2.948,0.646 3.042,0.823 0.094,0.177 10 false 1 2.906,2.656 3.104,2.833 0.198,0.177 10 false 3B 2.958,2.469 3.052,2.646 0.094,0.177 10 false 8 2.917,1.24 3.104,1.417 0.188,0.177 10 false 3A 2.938,1.052 3.115,1.229 0.177,0.177 10 false 29 5.708,2.271 5.938,2.448 0.229,0.177 10 false MB 6.083,2.26 6.313,2.438 0.229,0.177 10 false IG 0.396,1.24 1.521,2.365 1.125,1.125 10 false from Certification ECU (Smart Key ECU Assembly) 2.896,1.865 3.083,2.042 0.188,0.177 10 false 3A 2.917,1.667 3.094,1.844 0.177,0.177 10 false 54 2.906,2.26 3.094,2.438 0.188,0.177 10 false 3A 2.927,2.083 3.104,2.26 0.177,0.177 10 false 40 3.292,0.844 3.677,1.042 0.385,0.198 10 false 3F*2 3.417,0.635 3.51,0.813 0.094,0.177 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK DTC (SMART ENTRY AND START SYSTEM (for Start Function))
a.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

2.READ VALUE USING INTELLIGENT TESTER

B

2.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
IG SW Power switch on (IG) signal/ON or OFF ON: Power switch on (IG)
OFF: Power switch off
-

OK:

Normal conditions listed above are displayed.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK HARNESS AND CONNECTOR (DC/DC FUSE - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (DC/DC FUSE - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3E*1 or 3F*2 instrument panel junction block assembly connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3E-1 - Body ground*1 Power switch off 11 to 14 V
3F-1 - Body ground*2 Power switch off 11 to 14 V


*1: for LHD

*2: for RHD




OK

4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3A instrument panel junction block assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-54 - 3A-40 Always Below 1 Ω
3A-54 - Body ground Always 10 kΩ or higher




OK

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

U183666E02
6.51,3.01 6.667,3.5 false 1.99,0.354 2.25,0.563 0.26,0.208 10 false 3A 5.333,0.438 5.594,0.646 0.26,0.208 10 false 3B 0.885,2.302 1.146,2.51 0.26,0.208 10 false 3E 4.594,2.417 4.854,2.625 0.26,0.208 10 false MB 6.635,3.51 6.844,3.708 0.208,0.198 10 false IG 0.271,0.052 0.458,0.24 0.188,0.188 10 false *a 1.49,2.302 1.75,2.51 0.26,0.208 10 false 3F 1.156,2.26 1.344,2.448 0.188,0.188 10 false *b 1.771,2.26 1.958,2.448 0.188,0.188 10 false *c

Text in Illustration
*a Component without harness connected
(Instrument panel junction block assembly)
*b for LHD
*c for RHD - -

Standard Resistance:
Tester Connection Condition Specified Condition
3A-40 - MB-32 (IG) Always Below 1 Ω
3E-1 - 3A-54*1 Always 10 kΩ or higher
3E-1 - 3A-54*1 Auxiliary battery positive (+) → 3A-29
Auxiliary battery negative (-) → 3B-8
Below 1 Ω
3F-1 - 3A-54*2 Always 10 kΩ or higher
3F-1 - 3A-54*2 Auxiliary battery positive (+) → 3A-29
Auxiliary battery negative (-) → 3B-8
Below 1 Ω


*1: for LHD

*2: for RHD




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY