Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM › 2011.12–2014.12
RM2170E _58 Vehicle Interior _057036 LIGHTING (INT) _0278087 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Interior Light Auto Cut Circuit  


DESCRIPTION

When battery saving control operates while the interior lights are on, the main body ECU (multiplex network body ECU) opens the DOME CUT relay to turn off the lights.

WIRING DIAGRAM

E245982E05
5.719,2.615 6.875,3.229 1.156,0.615 10 false Main Body ECU (Multiplex Network Body ECU) 1.073,0.385 2.646,0.583 1.573,0.198 10 false from Auxiliary Battery 0.656,1.26 1.094,1.438 0.438,0.177 10 false DOME 1.656,1.781 2.469,1.969 0.813,0.188 10 false DOME CUT 1.667,1.021 1.771,1.198 0.104,0.177 10 false 2 1.667,1.417 1.771,1.594 0.104,0.177 10 false 5 2.313,1.021 2.406,1.198 0.094,0.177 10 false 1 2.313,1.417 2.406,1.594 0.094,0.177 10 false 3 2.771,1.448 3.698,1.646 0.927,0.198 10 false to Each Light 4.49,1.552 5.646,2.167 1.156,0.615 10 false Instrument Panel Junction Block Assembly 0.427,2.76 2.031,2.938 1.604,0.177 10 false *1: LED Type Headlight 5.771,0.292 5.948,0.469 0.177,0.177 10 false 15 5.688,0.49 6.01,0.646 0.323,0.156 10 false G59 6.104,0.49 6.625,0.844 0.521,0.354 10 false DOMR (*1,*3) 5.771,0.938 6.021,1.135 0.25,0.198 10 false 26 5.729,1.115 5.958,1.292 0.229,0.177 10 false MB 6.115,1.104 6.635,1.469 0.521,0.365 10 false DOMR (*2*4) 4.625,0.917 4.802,1.094 0.177,0.177 10 false 34 4.615,1.115 4.802,1.292 0.188,0.177 10 false 3B 4.115,0.354 4.792,0.573 0.677,0.219 10 false (*1,*3) 4.104,1 4.573,1.198 0.469,0.198 10 false (*2*4) 2.385,2.76 4.458,2.958 2.073,0.198 10 false *2: Halogen Type Headlight 0.427,3.135 1.885,3.333 1.458,0.198 10 false *3: w/ Rear Fog light 2.385,3.135 3.844,3.333 1.458,0.198 10 false *4: w/o Rear Fog light

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Active Test.


e.

Check that the relay operates.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Relay for Interior Light Auto Cut Function DOME CUT Relay ON/OFF -

OK:

Dome cut relay operates.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT DOME CUT RELAY
2.INSPECT DOME CUT RELAY
a.

Remove the DOME CUT relay from the No. 2 engine room relay block and No. 2 junction block assembly.


b.
E222294E15
1.104,0.948 1.333,0.417 1.333,0.417 1.5,0.417 false 0.802,1 1,0.417 1,0.417 1.083,0.417 false 0.833,1.75 0.667,1.75 0.667,1.75 0.573,1.281 false 1.417,1.75 1.25,1.75 1.25,1.75 1.156,1.354 false 0.219,0.229 0.531,0.427 0.313,0.198 10 false *a 1.146,0.333 1.458,0.531 0.313,0.198 10 false 5 1.552,0.333 1.865,0.531 0.313,0.198 10 false 1 1.5,1.667 1.813,1.865 0.313,0.198 10 false 2 0.906,1.667 1.219,1.865 0.313,0.198 10 false 3

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Voltage is not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Voltage is applied between terminals 1 and 2 Below 1 Ω


Result
Result Proceed to
OK (LED Headlight Type or w/ Rear Fog Light) A
OK (Halogen Headlight Type and w/o Rear Fog Light) B
NG C

Text in Illustration
*a Component without harness connected
(DOME CUT Relay)



A

3.CHECK HARNESS AND CONNECTOR (DOME CUT RELAY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

B

4.CHECK HARNESS AND CONNECTOR (DOME CUT RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

C

REPLACE DOME CUT RELAY

3.CHECK HARNESS AND CONNECTOR (DOME CUT RELAY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the G59 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay terminal 1 - G59-15 (DOMR) Always Below 1 Ω
Relay terminal 1 - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (DOME CUT RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3B instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay terminal 1 - 3B-34 Always Below 1 Ω
Relay terminal 1 - Body ground Always 10 kΩ or higher




OK

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

U183662E02
5.885,1.104 5.885,1.458 5.885,1.458 5.99,1.458 false 0.156,0.094 0.313,0.24 0.156,0.146 10 false *a 1.208,0.365 1.406,0.51 0.198,0.146 10 false 3B 4.667,0.365 4.917,0.531 0.25,0.167 10 false MB 6.021,1.375 6.635,1.542 0.615,0.167 10 false DOMR

Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
3B-34 - MB-26 (DOMR) Always Below 1 Ω




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY