Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2011.12–2014.12
RM2170E _58 Vehicle Interior _057037 METER / GAUGE / DISPLAY _0278095 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1500  Fuel Sender Open Detected  


DESCRIPTION

This DTC is stored when the combination meter assembly detects a fuel sender gauge malfunction via a direct line.

DTC No. DTC Detection Condition Trouble Area
B1500 When IG voltage is 9.5 V or more and the following condition is detected:
1.

Fuel sender gauge operation malfunction


·

Harness or connector

·

Fuel sender gauge assembly

·

Combination meter assembly



WIRING DIAGRAM

E237325E01
5.258,2.928 7.094,3.275 1.835,0.347 10 Combination Meter Assembly 6.09,0.896 6.327,1.053 0.237,0.157 10 L 5.888,0.896 6.066,1.046 0.178,0.150 10 2 2.106,2.246 2.225,2.396 0.119,0.150 10 3 2.097,0.889 2.216,1.039 0.119,0.150 10 2 0.296,3.037 2.115,3.362 1.819,0.325 10 Fuel Suction Tube Assembly with Pump and Gauge 0.482,1.491 1.122,2.153 0.640,0.662 10 Fuel Sender Gauge Assembly 1.288,1.452 1.406,1.602 0.119,0.150 10 2 1.288,2.058 1.406,2.208 0.119,0.150 10 1 1.821,2.246 2.040,2.395 0.218,0.149 10 FE 1.849,0.886 2.050,1.042 0.201,0.156 10 FS 5.258,2.783 5.593,2.931 0.334,0.149 10 G1 0.296,2.887 0.890,3.033 0.594,0.146 10 M22

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (FUEL INPUT)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Combination Meter / Data List.


e.

Check the values by referring to the table below.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Fuel Input Fuel input/Min.: 0, Max.: 127.5 10th segment comes on: 31.7 to 36.0 Unit: Liter
9th segment comes on: 28.3 to 31.7
8th segment comes on: 25.0 to 28.3
7th segment comes on: 21.6 to 25.0
6th segment comes on: 18.2 to 21.6
5th segment comes on: 14.8 to 18.2
4th segment comes on: 11.5 to 14.8
3rd segment comes on: 8.1 to 11.5
2nd segment comes on: 4.7 to 8.1
1st segment comes on: 3.8 to 4.7

Result:
Result Proceed to
Fuel level data can be displayed on the intelligent tester and DTC B1500 is output. A
Fuel level data cannot be displayed on the intelligent tester. B




A

REPLACE COMBINATION METER ASSEMBLY

B

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE)
2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE)
a.

Disconnect the M22 fuel sender gauge assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G1-2 (L) - M22-2 (FS) Always Below 1 Ω
G1-2 (L) - Body ground Always 10 kΩ or higher
M22-3 (FE) - Body ground Always Below 1 Ω




OK

3.INSPECT FUEL SENDER GAUGE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT FUEL SENDER GAUGE ASSEMBLY
a.

Remove the fuel sender gauge assembly (See page Engine / Hybrid System>1NZ-FXE FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL).


b.

Type A

i.
A267870E02
0.171,0.057 1.949,1.604 1.779,1.547 0.255,0.123 0.425,0.301 0.170,0.178 10 *a 0.743,2.016 0.880,2.170 0.138,0.154 10 F 0.743,4.192 0.880,4.346 0.138,0.154 10 E 2.166,2.099 0.921,2.099 false 1.58,4.275 0.943,4.275 false

Check that the float moves smoothly between E and F.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Float level is F (upper) 12.0 to 18.0 Ω
1 - 2 Float level is between F (upper) and E (lower) 12.0 to 415.0 Ω (Gradually changes)
1 - 2 Float level is E (lower) 405.0 to 415.0 Ω


Text in Illustration
*a Front view of wire harness connector
(to Fuel Sender Gauge Assembly)



c.

Type B

i.
A307401E02
0.115,0.094 2.052,1.563 1.938,1.469 1.188,4.083 0.51,4.083 true 2.417,2.25 1.365,2.25 false 0.208,0.146 0.729,0.542 0.521,0.396 10 false *a 0.354,4 0.677,4.229 0.323,0.229 10 false E 1.177,2.167 1.396,2.396 0.219,0.229 10 false F

Check that the float moves smoothly between E and F.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Float level is F (upper) 13.5 to 16.5 Ω
1 - 2 Float level is between F (upper) and E (lower) 13.5 to 414.5 Ω (Gradually changes)
1 - 2 Float level is E (lower) 405.5 to 414.5 Ω


Text in Illustration
*a Front view of wire harness connector
(to Fuel Sender Gauge Assembly)




OK

4.CHECK FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE

NG

REPLACE FUEL SENDER GAUGE ASSEMBLY

4.CHECK FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE
a.

Visually check for deformation on the fuel suction tube assembly with pump and gauge connector.

OK:

There is no deformation.




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE