Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2011.12–2014.12
RM2170E _58 Vehicle Interior _057039 SUPPLEMENTAL RESTRAINT SYSTEMS _0278099 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1835/58  Short in Curtain Shield Squib LH Circuit  B1836/58  Open in Curtain Shield Squib LH Circuit  B1837/58  Short to GND in Curtain Shield Squib LH Circuit  B1838/58  Short to B+ in Curtain Shield Squib LH Circuit  


DESCRIPTION

The curtain shield squib LH circuit consists of the airbag sensor assembly and curtain shield airbag assembly LH.

The airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the curtain shield squib LH circuit.

DTC No. DTC Detection Condition Trouble Area
B1835/58
·

The airbag sensor assembly receives a line short circuit signal in the curtain shield squib LH circuit during primary check.

·

Curtain shield squib LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Curtain shield airbag assembly LH (Curtain shield squib LH)

·

Airbag sensor assembly


B1836/58
·

The airbag sensor assembly receives an open circuit signal in the curtain shield squib LH circuit.

·

Curtain shield squib LH malfunction

·

Airbag sensor assembly malfunction


B1837/58
·

The airbag sensor assembly receives a short circuit to ground signal in the curtain shield squib LH circuit.

·

Curtain shield squib LH malfunction

·

Airbag sensor assembly malfunction


B1838/58
·

The airbag sensor assembly receives a short circuit to B+ signal in the curtain shield squib LH circuit.

·

Curtain shield squib LH malfunction

·

Airbag sensor assembly malfunction



WIRING DIAGRAM

C249389E06
0.695,2.481 1.032,2.643 0.336,0.163 10 M30 0.695,2.659 2.932,3.011 2.237,0.351 10 Curtain Shield Airbag Assembly LH (Curtain Shield Squib LH) 4.648,3.009 5.015,3.154 0.367,0.145 10 M36 4.703,1.986 5.086,2.149 0.384,0.163 10 ICL- 4.53,1.905 4.641,2.068 0.111,0.163 10 6 4.703,1.142 5.198,1.304 0.496,0.163 10 ICL+ 2.015,1.905 2.542,2.068 0.526,0.163 10 ICL- 2.015,1.065 2.478,1.228 0.463,0.163 10 ICL+ 4.53,1.065 4.641,1.228 0.111,0.163 10 7 2.41,1.905 2.521,2.068 0.111,0.163 10 2 2.41,1.065 2.521,1.228 0.111,0.163 10 1 4.648,3.188 6.282,3.364 1.634,0.176 10 Airbag Sensor Assembly

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK CONNECTORS
a.
C241752E03
0.521,1.125 0.521,1.573 false 1.385,0.99 1.385,0.563 1.385,0.563 1.615,0.563 false 0.635,0.969 0.76,1.125 0.125,0.156 10 false D 1.042,0.969 1.167,1.125 0.125,0.156 10 false C 1.625,0.969 1.75,1.125 0.125,0.156 10 false B 2.021,0.969 2.146,1.125 0.125,0.156 10 false A 2.469,0.979 2.646,1.156 0.177,0.177 10 false *2 0.448,1.573 0.604,1.729 0.156,0.156 10 false *1 1.635,0.469 1.792,0.625 0.156,0.156 10 false *3

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the curtain shield airbag assembly LH and airbag sensor assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the curtain shield airbag assembly LH and airbag sensor assembly.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the floor wire connector (on the curtain shield airbag assembly LH side) is not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



g.

Check that the short spring for the floor wire with the activation prevention mechanism is not deformed or damaged.

OK:

The short spring is not deformed or damaged.


Text in Illustration
*1 Curtain Shield Airbag Assembly LH
*2 Airbag Sensor Assembly
*3 Floor Wire



OK

2.CHECK CURTAIN SHIELD AIRBAG ASSEMBLY LH (CURTAIN SHIELD SQUIB LH)

NG

REPLACE FLOOR WIRE

2.CHECK CURTAIN SHIELD AIRBAG ASSEMBLY LH (CURTAIN SHIELD SQUIB LH)
a.
U183544E02
1.813,2.344 2,2.344 false 0.708,0.875 0.708,1.24 false 0.823,0.729 0.948,0.885 0.125,0.156 10 false D 1.135,0.729 1.26,0.885 0.125,0.156 10 false C 1.646,0.719 1.771,0.875 0.125,0.156 10 false B 1.802,0.719 1.927,0.875 0.125,0.156 10 false A 2.26,0.781 2.438,0.958 0.177,0.177 10 false *2 0.625,1.25 0.781,1.427 0.156,0.177 10 false *1 0.396,1.792 0.573,1.958 0.177,0.167 10 false *a 2.063,2.271 2.354,2.427 0.292,0.156 10 false SST 0.469,2.323 0.76,2.479 0.292,0.156 10 false M30

Connect the connector to the airbag sensor assembly.


b.

Connect SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the curtain shield airbag assembly LH (curtain shield squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) auxiliary battery terminal.



e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1835/58, B1836/58, B1837/58 or B1838/58 is not output.


HINT:

Codes other than DTCs B1835/58, B1836/58, B1837/58 and B1838/58 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Disconnect SST from connector C.

Text in Illustration
*1 Curtain Shield Airbag Assembly LH
*2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Curtain Shield Airbag Assembly LH)



OK

NG

3.CHECK FLOOR WIRE
3.CHECK FLOOR WIRE
a.
U183545E02
1.406,2.333 1.115,2.333 true 1.875,2.323 1.583,2.323 true 0.604,0.938 0.604,1.385 false 1.375,0.802 1.375,0.417 1.375,0.417 1.531,0.417 false 0.729,0.792 0.854,0.948 0.125,0.156 10 false D 1.083,0.802 1.208,0.958 0.125,0.156 10 false C 1.594,0.792 1.719,0.948 0.125,0.156 10 false B 1.948,0.792 2.073,0.948 0.125,0.156 10 false A 2.375,0.813 2.552,0.99 0.177,0.177 10 false *2 0.531,1.406 0.688,1.583 0.156,0.177 10 false *1 0.313,1.781 0.49,1.948 0.177,0.167 10 false *a 1.927,2.25 2.344,2.396 0.417,0.146 10 false ICL- 0.792,2.25 1.177,2.396 0.385,0.146 10 false ICL+ 1.573,0.344 1.729,0.521 0.156,0.177 10 false *3 0.563,2.594 0.854,2.75 0.292,0.156 10 false M30

Disconnect the floor wire from the airbag sensor assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M30-1 (ICL+) - Body ground Power switch on (IG) Below 1 V
M30-2 (ICL-) - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M30-1 (ICL+) - M30-2 (ICL-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M30-1 (ICL+) - Body ground Always 1 MΩ or higher
M30-2 (ICL-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M30-1 (ICL+) - M30-2 (ICL-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.

Text in Illustration
*1 Curtain Shield Airbag Assembly LH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Curtain Shield Airbag Assembly LH)




OK

4.CHECK DTC

NG

REPLACE FLOOR WIRE

4.CHECK DTC
a.
C238245E01
0.762,1.589 0.918,1.740 0.156,0.152 10 *1 2.147,0.987 2.322,1.143 0.174,0.156 10 *2 1.73,0.987 1.847,1.140 0.117,0.153 10 A 1.572,0.987 1.689,1.140 0.117,0.153 10 B 1.119,0.987 1.246,1.140 0.127,0.153 10 C 0.962,0.987 1.089,1.140 0.127,0.153 10 D 0.845,1.142 0.845,1.575 false

Connect the connectors to the curtain shield airbag assembly LH and airbag sensor assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.



d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1835/58, B1836/58, B1837/58 or B1838/58 is not output.


HINT:

Codes other than DTCs B1835/58, B1836/58, B1837/58 and B1838/58 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Curtain Shield Airbag Assembly LH
*2 Airbag Sensor Assembly



OK

NG