Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2011.12–2014.12
RM2170E _58 Vehicle Interior _057039 SUPPLEMENTAL RESTRAINT SYSTEMS _0278099 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1630/23  Rear Airbag Sensor RH Circuit Malfunction  


DESCRIPTION

The side collision sensor RH circuit (to determine deployment of the front seat airbag assembly RH and curtain shield airbag assembly RH) is composed of the airbag sensor assembly, side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.

The side No. 2 airbag sensor assembly RH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbag should be deployed.

DTC B1630/23 is stored when a malfunction is detected in the side No. 2 airbag sensor assembly RH.

DTC No. DTC Detection Condition Trouble Area
B1630/23
·

Side No. 2 airbag sensor assembly RH malfunction

·

Airbag sensor assembly malfunction


·

Side No. 2 airbag sensor assembly RH

·

Airbag sensor assembly



WIRING DIAGRAM

Refer to DTCs B1622/81, B1623/81, B1632/81, B1633/81 and B1642/81 (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>B1622/81).

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH
a.
C238223E01
0.969,0.972 1.119,1.124 0.150,0.152 10 *1 2.271,0.972 2.420,1.124 0.150,0.152 10 *2 2.036,0.972 2.163,1.137 0.128,0.166 10 A 1.883,0.972 2.011,1.137 0.128,0.166 10 B 1.425,0.972 1.552,1.137 0.128,0.166 10 C 1.268,0.972 1.396,1.137 0.128,0.166 10 D

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors.


d.

Connect the cable to the negative (-) auxiliary battery terminal.



f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1630/23 is output. A
DTC B1635/24 is output. B
DTCs B1630/23 and B1635/24 are not output. C


HINT:

Codes other than DTCs B1630/23 and B1635/24 may be output at this time, but they are not related to this check.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.

Text in Illustration
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly RH



A

B

REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH

C