Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CURTAIN SHIELD AIRBAG ASSEMBLY(w/o Occupant Classification System) › from 2015.11
RM2170E _58 Vehicle Interior _057039 SUPPLEMENTAL RESTRAINT SYSTEMS _0278104 CURTAIN SHIELD AIRBAG ASSEMBLY(w/o Occupant Classification System) A

SUPPLEMENTAL RESTRAINT SYSTEMS  CURTAIN SHIELD AIRBAG ASSEMBLY(w/o Occupant Classification System)  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:

Be sure to read Precaution thoroughly before servicing (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).


NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.REMOVE ROOF HEADLINING ASSEMBLY

Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 62180A 4.REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY

CAUTION:

When storing the curtain shield airbag assembly, keep the airbag deployment side facing upward.


a.

Check that the power switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.
B296245E02
2.375,0.417 1.938,0.417 true 1.667,1.833 1.094,1.833 true 1.948,1.823 1.948,2.823 true 1.875,2.844 2.031,3.021 0.156,0.177 10 false *1 0.885,1.75 1.083,1.938 0.198,0.188 10 true *2 1.75,0.333 1.906,0.51 0.156,0.177 10 false *3

Using a screwdriver with the tip wrapped with protective tape, release the airbag connector lock and disconnect the curtain shield airbag connector.

Text in Illustration
*1 Protective Tape
*2 Airbag Connector
*3 Airbag Connector Lock

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.



d.

Using a clip remover, remove the 7 pins.


e.

Using 2 screwdrivers, disengage the 2 claws and remove the clip from the body panel as shown in the illustration.

B296247E01
4.857,1.443 5.013,1.605 0.155,0.163 10 *1 5.172,1.183 5.327,1.346 0.155,0.163 10 *2 5.007,1.261 5.163,1.261 false 4.915,1.237 4.915,1.41 false

Text in Illustration
*1 Body Panel *2 Curtain Shield Airbag Assembly

HINT:

Perform the same procedure for the other clips.



f.

While holding the curtain shield airbag assembly, remove the bolt and disengage the 4 clips.

B296248

NOTICE:

When removing the curtain shield airbag assembly, have assistants hold it to prevent it from bending.



g.
B296250E02
0.49,0.875 0.271,0.875 true 0.063,0.781 0.302,0.99 0.24,0.208 10 true (A)

Disengage the hook (A).


h.

Disengage the 3 hooks to remove the curtain shield airbag assembly as shown in the illustration.


i.

Remove the 3 spacers from the curtain shield airbag assembly.