Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SIDE AIRBAG SENSOR(for Rear Side) › 2015.11–2017.06
RM2170E _58 Vehicle Interior _057039 SUPPLEMENTAL RESTRAINT SYSTEMS _0278108 SIDE AIRBAG SENSOR A

SUPPLEMENTAL RESTRAINT SYSTEMS  SIDE AIRBAG SENSOR  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:

Be sure to read Precaution thoroughly before servicing (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).


NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 58165F 2.REMOVE FRONT FLOOR COVER RH

Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 58166B 4.REMOVE FRONT FLOOR COVER LH (for LH Side)

Hide 62312B 6.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

HINT:

Disconnect the front door opening trim weatherstrip to the extent that allows the removal of the center pillar lower garnish.


Hide 62332A 8.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

HINT:

Disconnect the rear door opening trim weatherstrip to the extent that allows the removal of the center pillar lower garnish.


Hide 62414A 9.REMOVE CENTER PILLAR LOWER GARNISH

Hide 89860A 10.REMOVE SIDE AIRBAG SENSOR ASSEMBLY

a.

Check that the power switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Disconnect the connector from the side airbag sensor assembly.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


i.

Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

B296233E01
1.244,1.622 1.405,1.770 0.160,0.148 10 *1 1.844,2.337 2.004,2.486 0.160,0.148 10 *2 1.497,2.371 1.658,2.520 0.160,0.148 10 *a 1.63,1.563 1.790,1.711 0.160,0.148 10 *b 1.377,1.686 1.432,1.686 1.432,1.686 1.588,1.843 false 1.816,2.07 1.896,2.149 1.896,2.149 1.896,2.32 false 3.16,1.638 3.321,1.786 0.160,0.148 10 *1 3.785,2.336 3.945,2.484 0.160,0.148 10 *2 3.388,2.396 3.548,2.544 0.160,0.148 10 *a 3.506,1.602 3.667,1.750 0.160,0.148 10 *b 3.757,2.068 3.836,2.148 3.836,2.148 3.836,2.319 false 3.307,1.699 3.362,1.699 3.362,1.699 3.519,1.856 false 1.005,1.72 1.220,1.895 0.216,0.175 10 (A) 1.218,1.785 1.281,1.785 1.281,1.785 1.459,1.962 false 2.926,1.74 3.141,1.916 0.216,0.175 10 (A) 3.139,1.805 3.202,1.805 3.202,1.805 3.379,1.982 false

Text in Illustration
*1 White Housing Lock *2 Yellow CPA
*a Slide *b Push


ii.

Push down the white housing lock again and disconnect the connector.

NOTICE:

Do not push down the part (A) shown in the illustration when disconnecting the connector.




d.

Remove the bolt and side airbag sensor assembly from the vehicle body.

NOTICE:

Loosen the bolt while holding the side airbag sensor assembly because the side airbag sensor assembly pin (stopper) is easily damaged.



e.

After disconnecting the connector, check that the position of the white housing lock is correct as shown in the illustration.

B296256E05
5.009,0.509 5.192,0.679 0.183,0.17 10 *b 1.787,0.509 1.97,0.679 0.183,0.17 10 *a

Text in Illustration
*a Correct *b Incorrect