Use the same procedure for the RH side and LH side.
The procedure listed below is for the LH side.
1. PRECAUTION
Be sure to read Precaution thoroughly before servicing (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
71940A
2.REMOVE REAR SEAT HEADREST ASSEMBLY
71960B
3.REMOVE REAR CENTER SEAT HEADREST ASSEMBLY (for LH Side)
58165F
4.REMOVE FRONT FLOOR COVER RH
for Separate Type Seatback: (See page Vehicle Interior>SEAT>REAR SEAT ASSEMBLY(for Separate Type Seatback)>REMOVAL)
for Bench Type Seatback: (See page Vehicle Interior>SEAT>REAR SEAT ASSEMBLY(for Bench Type Seatback)>REMOVAL)
58166B
5.REMOVE FRONT FLOOR COVER LH
for Separate Type Seatback: (See page Vehicle Interior>SEAT>REAR SEAT ASSEMBLY(for Separate Type Seatback)>REMOVAL)
for Bench Type Seatback: (See page Vehicle Interior>SEAT>REAR SEAT ASSEMBLY(for Bench Type Seatback)>REMOVAL)
58167H
6.REMOVE FRONT CENTER FLOOR COVER
for Separate Type Seatback: (See page Vehicle Interior>SEAT>REAR SEAT ASSEMBLY(for Separate Type Seatback)>REMOVAL)
for Bench Type Seatback: (See page Vehicle Interior>SEAT>REAR SEAT ASSEMBLY(for Bench Type Seatback)>REMOVAL)
7.REMOVE REAR SEAT CUSHION ASSEMBLY
for Separate Type Seatback: (See page Vehicle Interior>SEAT>REAR SEAT ASSEMBLY(for Separate Type Seatback)>REMOVAL)
for Bench Type Seatback: (See page Vehicle Interior>SEAT>REAR SEAT ASSEMBLY(for Bench Type Seatback)>REMOVAL)
8.REMOVE REAR SEATBACK ASSEMBLY
for Separate Type Seatback LH Side: (See page Vehicle Interior>SEAT>REAR SEAT ASSEMBLY(for Separate Type Seatback)>REMOVAL)
for Separate Type Seatback RH Side: (See page Vehicle Interior>SEAT>REAR SEAT ASSEMBLY(for Separate Type Seatback)>REMOVAL)
for Bench Type Seatback: (See page Vehicle Interior>SEAT>REAR SEAT ASSEMBLY(for Bench Type Seatback)>REMOVAL)
9.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
67918A
10.REMOVE REAR DOOR SCUFF PLATE
62332A
11.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP
Disconnect the rear door opening trim weatherstrip to the extent that allows the removal of the deck trim side panel assembly.
58410B
12.REMOVE DECK BOARD ASSEMBLY
64997
13.REMOVE DECK FLOOR BOX LH
64995
14.REMOVE DECK FLOOR BOX RH
Use the same procedure for the RH side and LH side (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL).
64330D
15.REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY
64716D
16.REMOVE REAR DECK TRIM COVER
73370
17.DISCONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY
81330
18.REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY (for LH Side)
64740C
19.REMOVE DECK TRIM SIDE PANEL ASSEMBLY
89860C
20.REMOVE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY
Check that the power switch is off.
Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Disconnect the connector from the side No. 2 airbag sensor assembly.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)
| *1 | White Housing Lock | *2 | Yellow CPA |
| *a | Connector Lock is Released | - | - |
Push down the white housing lock again and disconnect the connector.
Do not push down the part (A) shown in the illustration when disconnecting the connector.
Remove the bolt and side No. 2 airbag sensor assembly from the vehicle body.
Loosen the bolt while holding the side No. 2 airbag sensor assembly because the side No. 2 airbag sensor assembly pin (stopper) is easily damaged.
After disconnecting the connector, check that the position of the white housing lock is correct as shown in the illustration.
| *a | Incorrect | *b | Correct |