72211
1.INSTALL SEAT TRACK ADJUSTING HANDLE
Engage the 2 springs to install the seat track adjusting handle to the separate type front seat cushion spring assembly.
71640S
2.INSTALL SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY
Engage the 4 guides to install the separate type front seatback spring assembly to the separate type front seat cushion spring assembly.
Install the 4 bolts.
71538B
3.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH
Engage the 5 claws to install the front seat cushion edge protector LH.
71537H
4.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH
Engage the 5 claws to install the front seat cushion edge protector RH.
71074S
5.INSTALL SEPARATE TYPE FRONT SEATBACK COVER
Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 8 new hog rings.
Be careful not to damage the separate type front seatback cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.
73920A
6.INSTALL FRONT SEAT AIRBAG ASSEMBLY
7.INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD
Temporarily install the separate type front seatback cover with pad.
Install the 3 brackets with the 2 nuts.
For vehicles with a front seat airbag assembly, the separate type front seatback cover must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.
Make sure that the strap is not twisted after installing the nut.
Install the bracket securely.
Turn back the separate type front seatback cover.
Using hog ring pliers, install 2 new hog rings.
Be careful not to damage the separate type front seatback cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.
Using hog ring pliers, install 3 new hog rings.
Be careful not to damage the separate type front seatback cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.
Using hog ring pliers, install 5 new hog rings.
Be careful not to damage the separate type front seatback cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.
71072S
8.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER
Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 18 new hog rings.
Be careful not to damage the separate type front seat cushion cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.
Using hog ring pliers, install 2 new hog rings.
Be careful not to damage the separate type front seat cushion cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.
9.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD
for Front Passenger Side:
Engage the clamp to install the connector as shown in the illustration.
Temporarily install the separate type front seat cushion cover with pad.
Engage each hook.
73920A
10.CONNECT FRONT SEAT AIRBAG ASSEMBLY
for Driver Side:
Engage the claw and 6 clamps to install the front seat airbag assembly wire harness.
for Front Passenger Side:
Engage the claw and 3 clamps to install the front seat airbag assembly wire harness.
Engage the fastener to secure the front seat airbag assembly wire harness.
71812D
11.INSTALL FRONT SEAT CUSHION SHIELD
Engage the 2 claws, 4 guides and clip to install the front seat cushion shield.
Install the screw.
72526A
12.INSTALL RECLINING ADJUSTER RELEASE HANDLE
Engage the claw to install the reclining adjuster release handle.
71849
13.INSTALL SEAT ADJUSTER COVER CAP
Install the 2 seat adjuster cover caps.
14.INSTALL FRONT SEAT BELT ANCHOR PLATE
73240
15.INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Driver Side)
73230
16.INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side)
71862
17.INSTALL FRONT SEAT INNER CUSHION SHIELD
Engage the 2 claws and 5 guides to install the front seat inner cushion shield.
71074S
18.CONNECT SEPARATE TYPE FRONT SEATBACK COVER
Connect the rubber band of the separate type front seatback cover.