Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM › 2011.12–2017.06
RM2170E _58 Vehicle Interior _057042 HEATING / AIR CONDITIONING _0278125 AIR CONDITIONING SYSTEM J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  Blower Motor Circuit  


DESCRIPTION

The blower motor with fan sub-assembly is operated by signals from the air conditioning amplifier assembly. Blower motor with fan sub-assembly speed signals are transmitted in accordance with changes in the duty ratio.

WIRING DIAGRAM

E229256E42
2.972,0.933 3.069,1.107 0.097,0.174 10 3 5.295,0.614 5.469,0.788 0.173,0.174 10 22 3.71,1.345 4.036,1.520 0.326,0.174 10 GND 2.042,1.252 2.348,1.426 0.306,0.174 10 HTR 0.2,1.002 1.064,1.335 0.865,0.333 10 from Auxiliary Battery 3.865,0.707 4.052,0.881 0.187,0.174 10 SI 3.216,1.035 3.413,1.210 0.198,0.174 10 +B 5.6,0.707 5.920,0.881 0.320,0.174 10 BLW 5.291,3.264 5.589,3.439 0.298,0.174 10 G34 5.291,3.423 6.895,3.755 1.604,0.332 10 Air Conditioning Amplifier Assembly 3.016,1.764 3.299,1.938 0.283,0.174 10 G32 3.016,1.923 4.441,2.310 1.425,0.387 10 Blower Motor with Fan Sub-assembly 4.164,0.614 4.261,0.788 0.097,0.174 10 2 4.164,1.251 4.261,1.426 0.097,0.174 10 1 5.711,1.784 6.502,1.959 0.792,0.174 10 Duty Control

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Air Conditioner / Active Test.


e.

Check the operation by referring to the table below.


Air Conditioner
Tester Display Test Part Control Range Diagnostic Note
Blower Motor Blower motor with fan sub-assembly Min.: 0, Max.: 31 -

Result:
Result Proceed to
OK A
NG (Blower motor with fan sub-assembly does not operate) B
NG (Blower motor with fan sub-assembly operates but does not change speed) C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR WITH FAN SUB-ASSEMBLY - BODY GROUND)

C

6.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR WITH FAN SUB-ASSEMBLY - BODY GROUND)
a.

Disconnect the G32 blower motor with fan sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G32-1 (GND) - Body ground Always Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR WITH FAN SUB-ASSEMBLY - POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR WITH FAN SUB-ASSEMBLY - POWER SOURCE)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G32-3 (+B) - Body ground Power switch off 11 to 14 V




OK

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BLOWER MOTOR WITH FAN SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BLOWER MOTOR WITH FAN SUB-ASSEMBLY)
a.

Disconnect the G34 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G34-22 (BLW) - G32-2 (SI) Always Below 1 Ω
G34-22 (BLW) - Body ground Always 10 kΩ or higher




OK

5.INSPECT BLOWER MOTOR WITH FAN SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT BLOWER MOTOR WITH FAN SUB-ASSEMBLY
a.

Reconnect the G32 blower motor with fan sub-assembly connector.


b.
U183680E02
1.561,0.611 1.864,0.767 0.303,0.156 10 G34 0.181,0.156 0.335,0.311 0.155,0.156 10 *a 0.325,2.974 0.650,3.130 0.325,0.156 10 BLW 0.745,2.582 0.58,2.952 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G34-22 (BLW) - Body ground Always 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)



OK

6.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPLACE BLOWER MOTOR WITH FAN SUB-ASSEMBLY

6.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY
a.
U183726E02
2.167,1.146 2.167,1.854 false 1.385,0.281 1.667,0.438 0.281,0.156 10 false G34 0.177,0.156 0.333,0.313 0.156,0.156 10 false *a 1.979,1.875 2.302,2.031 0.323,0.156 10 false BLW 2.823,3.854 3.146,4.01 0.323,0.156 10 false GND

Remove the air conditioning amplifier assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL).


b.

Reconnect the G34 air conditioning amplifier assembly connector.


c.

Turn the power switch on (IG).


d.

Turn the blower switch on (LO).


e.

Measure the waveform between terminal G34-22 (BLW) of the air conditioning amplifier assembly and body ground.

OK:

Waveform is similar to that shown in the illustration.


HINT:

The waveform varies with the blower speed.



Item Content
Tool setting 1 V/DIV., 500 μs/DIV.
Vehicle condition Power switch on (IG)
Blower switch on (LO)

Text in Illustration
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


OK

REPLACE BLOWER MOTOR WITH FAN SUB-ASSEMBLY

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY