Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM › from 2014.12
RM2170E _58 Vehicle Interior _057042 HEATING / AIR CONDITIONING _0278125 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B1471/71  A/C Inverter High Voltage Power Resource System Malfunction  


DESCRIPTION

The A/C inverter assembly monitors the voltage of the HV battery. It stops compressor control and stores the DTC when the monitored voltage is outside the specified range.

The DTC will be stored as a history DTC. Compressor control may not resume unless the power switch is turned off.

DTC No. DTC Detection Condition Trouble Area
B1471/71
·

Open or short in A/C inverter high voltage power resource system

·

The boost inverter is broken or malfunctioning


·

Electric vehicle fuse

·

No. 2 engine wire (harness or connector between compressor with motor assembly and inverter with converter assembly)

·

Compressor with motor assembly

·

Hybrid control system

·

CAN communication system



WIRING DIAGRAM

E235673E44
0.281,6.281 1.333,6.74 1.052,0.458 10 false Compressor with Motor Assembly 5.958,4.063 6.885,4.542 0.927,0.479 10 false Hybrid Vehicle Control ECU 6.052,1.844 6.344,1.99 0.292,0.146 10 false STB 6.052,2.854 6.344,3 0.292,0.146 10 false ITE 6.052,3.375 6.344,3.521 0.292,0.146 10 false CLK 6.052,2.354 6.292,2.5 0.24,0.146 10 false ETI 0.854,1.833 1.188,1.979 0.333,0.146 10 false STBI 0.927,2.854 1.188,3 0.26,0.146 10 false DIN 0.906,3.344 1.198,3.49 0.292,0.146 10 false CLK 0.948,3.917 1.188,4.063 0.24,0.146 10 false IG1 0.865,4.479 1.198,4.625 0.333,0.146 10 false GND 0.979,5.281 1.292,5.51 0.313,0.229 10 false PE 0.979,5.781 1.344,6.042 0.365,0.26 10 false PB 0.771,2.333 1.188,2.479 0.417,0.146 10 false DOUT 1.333,1.833 1.646,2.052 0.313,0.219 10 false C22 1.333,2.344 1.615,2.49 0.281,0.146 10 false C22 1.333,2.844 1.615,2.99 0.281,0.146 10 false C22 1.333,3.365 1.615,3.51 0.281,0.146 10 false C22 1.333,4.479 1.615,4.646 0.281,0.167 10 false C22 1.333,3.917 1.615,4.063 0.281,0.146 10 false C22 5.781,1.74 5.969,1.885 0.188,0.146 10 false 11 5.854,2.24 6.031,2.385 0.177,0.146 10 false 8 5.854,2.76 6.031,2.906 0.177,0.146 10 false 9 5.792,3.271 5.969,3.417 0.177,0.146 10 false 10 4.927,7.104 7.063,7.365 2.135,0.26 10 false Inverter with Converter Assembly 5.229,5.677 5.333,5.844 0.104,0.167 10 false 1 5.229,5.156 5.333,5.323 0.104,0.167 10 false 2 1.365,5.25 1.74,5.521 0.375,0.271 10 false D1 1.365,5.771 1.729,6.031 0.365,0.26 10 false D1 1.427,5.073 1.531,5.219 0.104,0.146 10 false 1 1.438,5.583 1.542,5.75 0.104,0.167 10 false 2 1.417,1.646 1.521,1.792 0.104,0.146 10 false 4 1.417,2.146 1.521,2.313 0.104,0.167 10 false 3 1.417,2.667 1.521,2.813 0.104,0.146 10 false 2 1.417,3.167 1.521,3.333 0.104,0.167 10 false 1 1.417,3.74 1.521,3.885 0.104,0.146 10 false 6 1.427,4.292 1.531,4.458 0.104,0.167 10 false 5 5.406,5.156 5.813,5.302 0.406,0.146 10 false ACPE 5.406,5.667 5.813,5.813 0.406,0.146 10 false ACPB 5.719,5.938 6.229,6.531 0.51,0.594 10 false Electric Vehicle Fuse 2.583,4.042 3.115,4.25 0.531,0.208 10 false HTR-IG 4.167,3.906 5.563,4.052 1.396,0.146 10 false from IG1 NO. 1 Relay 2.26,7.135 3.979,7.281 1.719,0.146 10 false : CAN Communication Line 4.927,6.948 5.177,7.156 0.25,0.208 10 false D2 5.958,3.896 6.25,4.083 0.292,0.188 10 false A72 0.281,1.063 2.563,1.26 2.281,0.198 10 false Air Conditioning Amplifier Assembly 2.729,6.313 3.938,6.542 1.208,0.229 10 false No. 2 Engine Wire

CAUTION / NOTICE / HINT

CAUTION:
·

Wear insulated gloves and pull out the service plug grip before inspection as procedures may require disconnecting high-voltage connectors. Carry the removed service plug in your pocket to prevent other technicians from accidentally reconnecting it while you are servicing the vehicle.

·

Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.



NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

The hybrid control system and air conditioning system output DTCs separately. Inspect DTCs following the diagnosis procedure for the hybrid control system first if any DTCs from those systems are output simultaneously.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Use the intelligent tester to check if the CAN communication system is functioning normally.

Result:
Result Proceed to
CAN DTC is not output A
CAN DTC is output B




A

2.CHECK DIAGNOSTIC TROUBLE CODE (HYBRID CONTROL SYSTEM)

B

2.CHECK DIAGNOSTIC TROUBLE CODE (HYBRID CONTROL SYSTEM)
a.

Check if DTCs for the hybrid control system are output using the intelligent tester.

OK:

Hybrid control system DTCs are not output.




OK

3.INSPECT ELECTRIC VEHICLE FUSE

NG

3.INSPECT ELECTRIC VEHICLE FUSE
CAUTION:

Be sure to wear insulated gloves.


a.

Turn the power switch off.


b.

Remove the service plug grip (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>SERVICE PLUG GRIP>REMOVAL).

CAUTION:

Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.


NOTICE:

After removing the service plug grip, turning the power switch to on (READY) may cause a malfunction. Do not turn the power switch to on (READY) with the service plug grip removed.



c.

Remove the connector cover assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>INVERTER WITH CONVERTER>REMOVAL).

NOTICE:

Be sure to prevent foreign objects or water from entering the inverter with converter assembly.



d.
E238086E03
1.448,1.052 2.406,1.052 false 1.417,1.771 2.406,1.771 false 1.302,0.958 1.427,1.156 0.125,0.198 10 false A 1.302,1.688 1.427,1.885 0.125,0.198 10 false B 0.5,0.729 0.802,1.031 0.302,0.302 10 false *a

Check that bolts A and B are tightened securely.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Item
(Tester Connection)
Condition Specified Condition
Electric vehicle fuse
(A - B)
Always Below 1 Ω


Text in Illustration
*a Electric Vehicle Fuse



OK

4.INSPECT NO. 2 ENGINE WIRE

NG

4.INSPECT NO. 2 ENGINE WIRE
CAUTION:

Be sure to wear insulated gloves.


a.

Disconnect the No. 2 engine wire connector (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>INVERTER WITH CONVERTER>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D1-1 (PE) - D2-2 (ACPE) Always Below 1 Ω
D1-2 (PB) - D2-1 (ACPB) Always Below 1 Ω
D1-1 (PE) - Body ground Always 10 kΩ or higher
D1-2 (PB) - Body ground Always 10 kΩ or higher




OK

REPLACE COMPRESSOR WITH MOTOR ASSEMBLY

NG