Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM › from 2014.12
RM2170E _58 Vehicle Interior _057042 HEATING / AIR CONDITIONING _0278125 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B1498/98  Communication Malfunction (A/C Inverter Local)  


DESCRIPTION

The hybrid vehicle control ECU and compressor with motor assembly transmit information to one another via a communication line. Compressor control is stopped and the DTC is stored if communication information is cut off or abnormal information occurs.

The DTC is also detected if high-voltage power supplied from the inverter with converter assembly to the compressor control circuit is shut off.

The DTC will be stored as a history DTC.

DTC No. DTC Detection Condition Trouble Area
B1498/98
·

Communication line error or open between the hybrid vehicle control ECU and compressor with motor assembly.


·

High-voltage power source is shut off.


·

Harness or connector between hybrid vehicle control ECU, compressor with motor assembly and body ground

·

Hybrid vehicle control ECU

·

Compressor with motor assembly

·

No. 2 engine wire (harness or connector between compressor with motor assembly and inverter with converter assembly)

·

Electric vehicle fuse

·

CAN communication system

·

Hybrid control system



WIRING DIAGRAM

E235673E44
0.281,6.281 1.333,6.74 1.052,0.458 10 false Compressor with Motor Assembly 5.958,4.063 6.885,4.542 0.927,0.479 10 false Hybrid Vehicle Control ECU 6.052,1.844 6.344,1.99 0.292,0.146 10 false STB 6.052,2.854 6.344,3 0.292,0.146 10 false ITE 6.052,3.375 6.344,3.521 0.292,0.146 10 false CLK 6.052,2.354 6.292,2.5 0.24,0.146 10 false ETI 0.854,1.833 1.188,1.979 0.333,0.146 10 false STBI 0.927,2.854 1.188,3 0.26,0.146 10 false DIN 0.906,3.344 1.198,3.49 0.292,0.146 10 false CLK 0.948,3.917 1.188,4.063 0.24,0.146 10 false IG1 0.865,4.479 1.198,4.625 0.333,0.146 10 false GND 0.979,5.281 1.292,5.51 0.313,0.229 10 false PE 0.979,5.781 1.344,6.042 0.365,0.26 10 false PB 0.771,2.333 1.188,2.479 0.417,0.146 10 false DOUT 1.333,1.833 1.646,2.052 0.313,0.219 10 false C22 1.333,2.344 1.615,2.49 0.281,0.146 10 false C22 1.333,2.844 1.615,2.99 0.281,0.146 10 false C22 1.333,3.365 1.615,3.51 0.281,0.146 10 false C22 1.333,4.479 1.615,4.646 0.281,0.167 10 false C22 1.333,3.917 1.615,4.063 0.281,0.146 10 false C22 5.781,1.74 5.969,1.885 0.188,0.146 10 false 11 5.854,2.24 6.031,2.385 0.177,0.146 10 false 8 5.854,2.76 6.031,2.906 0.177,0.146 10 false 9 5.792,3.271 5.969,3.417 0.177,0.146 10 false 10 4.927,7.104 7.063,7.365 2.135,0.26 10 false Inverter with Converter Assembly 5.229,5.677 5.333,5.844 0.104,0.167 10 false 1 5.229,5.156 5.333,5.323 0.104,0.167 10 false 2 1.365,5.25 1.74,5.521 0.375,0.271 10 false D1 1.365,5.771 1.729,6.031 0.365,0.26 10 false D1 1.427,5.073 1.531,5.219 0.104,0.146 10 false 1 1.438,5.583 1.542,5.75 0.104,0.167 10 false 2 1.417,1.646 1.521,1.792 0.104,0.146 10 false 4 1.417,2.146 1.521,2.313 0.104,0.167 10 false 3 1.417,2.667 1.521,2.813 0.104,0.146 10 false 2 1.417,3.167 1.521,3.333 0.104,0.167 10 false 1 1.417,3.74 1.521,3.885 0.104,0.146 10 false 6 1.427,4.292 1.531,4.458 0.104,0.167 10 false 5 5.406,5.156 5.813,5.302 0.406,0.146 10 false ACPE 5.406,5.667 5.813,5.813 0.406,0.146 10 false ACPB 5.719,5.938 6.229,6.531 0.51,0.594 10 false Electric Vehicle Fuse 2.583,4.042 3.115,4.25 0.531,0.208 10 false HTR-IG 4.167,3.906 5.563,4.052 1.396,0.146 10 false from IG1 NO. 1 Relay 2.26,7.135 3.979,7.281 1.719,0.146 10 false : CAN Communication Line 4.927,6.948 5.177,7.156 0.25,0.208 10 false D2 5.958,3.896 6.25,4.083 0.292,0.188 10 false A72 0.281,1.063 2.563,1.26 2.281,0.198 10 false Air Conditioning Amplifier Assembly 2.729,6.313 3.938,6.542 1.208,0.229 10 false No. 2 Engine Wire

CAUTION / NOTICE / HINT

CAUTION:
·

Wear insulated gloves and pull out the service plug grip before inspection as procedures may require disconnecting high-voltage connectors. Carry the removed service plug in your pocket to prevent other technicians from accidentally reconnecting it while you are servicing the vehicle.

·

Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.



NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

The hybrid control system and air conditioning system output DTCs separately. Inspect DTCs following the diagnosis procedure for the hybrid control system first if any DTCs from those systems are output simultaneously.

·

Depending on the timing of the power supply to the 12 V power supply circuit and high-voltage circuit when the power switch is turned on (READY), an abnormal information signal may be output, causing this DTC to be stored. If the output DTC is a code that was memorized in the past, check the fuses and wire harnesses. If there is no malfunction, clear the DTC.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Use the intelligent tester to check if the CAN communication system is functioning normally.

Result:
Result Proceed to
CAN DTC is not output A
CAN DTC is output B




A

2.CHECK DIAGNOSTIC TROUBLE CODE

B

2.CHECK DIAGNOSTIC TROUBLE CODE
a.

Check if DTCs for the hybrid control system are output using the intelligent tester.


Result:
Result Proceed to
DTC is not output A
Only DTC P3108 is output A
DTCs other than P3108 are output B



A

3.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY - BODY GROUND)

B

3.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY - BODY GROUND)
CAUTION:

Do not disconnect the connector on the high-voltage side.


a.

Disconnect the C22 compressor with motor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C22-5 (GND) - Body ground Always Below 1 Ω




OK

4.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY - IG POWER SOURCE, GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY - IG POWER SOURCE, GROUND)
a.

Turn the power switch on (IG).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C22-6 (IG1) - C22-5 (GND) Power switch on (IG) 11 to 14 V
C22-6 (IG1) - C22-5 (GND) Power switch off Below 1 V




OK

5.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - COMPRESSOR WITH MOTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - COMPRESSOR WITH MOTOR)
a.

Disconnect the A72 hybrid vehicle control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C22-1 (CLK) - A72-10 (CLK) Always Below 1 Ω
C22-2 (DIN) - A72-9 (ITE) Always Below 1 Ω
C22-3 (DOUT) - A72-8 (ETI) Always Below 1 Ω
C22-1 (CLK) - Body ground Always 10 kΩ or higher
C22-2 (DIN) - Body ground Always 10 kΩ or higher
C22-3 (DOUT) - Body ground Always 10 kΩ or higher




OK

6.INSPECT ELECTRIC VEHICLE FUSE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT ELECTRIC VEHICLE FUSE
CAUTION:

Be sure to wear insulated gloves.


a.

Turn the power switch off.


b.

Remove the service plug grip (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>SERVICE PLUG GRIP>REMOVAL).

CAUTION:

Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.


NOTICE:

After removing the service plug grip, turning the power switch on (READY) may cause a malfunction. Do not turn the power switch on (READY) with the service plug grip removed.



c.

Remove the connector cover assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>INVERTER WITH CONVERTER>REMOVAL).

NOTICE:

Be sure to prevent foreign objects or water from entering the inverter with converter assembly.



d.
E238086E03
1.448,1.052 2.406,1.052 false 1.417,1.771 2.406,1.771 false 1.302,0.958 1.427,1.156 0.125,0.198 10 false A 1.302,1.688 1.427,1.885 0.125,0.198 10 false B 0.5,0.729 0.802,1.031 0.302,0.302 10 false *a

Check that bolts A and B are tightened securely.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Item
(Tester Connection)
Condition Specified Condition
Electric vehicle fuse
(A - B)
Always Below 1 Ω


Text in Illustration
*a Electric Vehicle Fuse



OK

7.INSPECT NO. 2 ENGINE WIRE

NG

7.INSPECT NO. 2 ENGINE WIRE
CAUTION:

Be sure to wear insulated gloves.


a.

Disconnect the No. 2 engine wire connector (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>INVERTER WITH CONVERTER>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D1-1 (PE) - D2-1 (ACPE) Always Below 1 Ω
D1-2 (PB) - D2-2 (ACPB) Always Below 1 Ω
D1-1 (PE) - Body ground Always 10 kΩ or higher
D1-2 (PB) - Body ground Always 10 kΩ or higher




OK

8.REPLACE COMPRESSOR WITH MOTOR ASSEMBLY

NG

8.REPLACE COMPRESSOR WITH MOTOR ASSEMBLY
a.

Replace the compressor with motor assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>COMPRESSOR>REMOVAL).

HINT:

Since the compressor with motor assembly cannot be inspected while it is removed from the vehicle, replace the compressor with motor assembly with a new or known good one and check that the condition returns to normal.



b.

Check for the DTC.

Result:
Result Proceed to
DTC B1498/98 is not output A
DTC B1498/98 is output B




A

END (COMPRESSOR WITH MOTOR ASSEMBLY WAS DEFECTIVE)

B