The cooler thermistor (solar sensor) is installed on the upper side of the instrument panel. It detects sunlight and creates a signal that is used for air conditioning control in AUTO mode. The output voltage from the cooler thermistor (solar sensor) varies in accordance with the amount of sunlight. When the sunlight increases, the output voltage increases. As the sunlight decreases, the output voltage decreases. The air conditioning amplifier assembly detects changes in the output voltage from the cooler thermistor (solar sensor).
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| B14A2 | Short in cooler thermistor (solar sensor) circuit | ·
Cooler thermistor (solar sensor) ·
Harness or connector between cooler thermistor (solar sensor) and air conditioning amplifier assembly ·
Air conditioning amplifier assembly |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Air Conditioner / Data List.
Check the value(s) by referring to the table below.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Solar Sensor (D Side) | Solar sensor /
Min.: 0 Max.: 255 |
Solar sensor value increases as brightness increases | - |
The display is as specified in the Normal Condition column.
| Result | Proceed to |
|---|---|
| NG | A |
| OK (When troubleshooting according to Problem Symptoms Table) | B |
| OK (When troubleshooting according to the DTC) | C |
A
B
(See pageVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>PROBLEM SYMPTOMS TABLE)
C
Disconnect the G61 Cooler thermistor (solar sensor) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G61-1 (SS+) - G61-2 (SS-) | Power switch off | Below 1 V |
| G61-1 (SS+) - G61-2 (SS-) | Power switch on (IG) | 4.75 to 5.25 V |
| *a | Front view of wire harness connector
(to Cooler Thermistor (Solar Sensor)) |
OK
NG
Remove the cooler thermistor (solar sensor) (See page Vehicle Interior>HEATING / AIR CONDITIONING>SOLAR SENSOR>REMOVAL).
Reconnect the G61 cooler thermistor (solar sensor) connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G61-1 (SS+) - G61-2 (SS-) | Sensor is subjected to electric light | 0.8 to 4.3 V |
| G61-1 (SS+) - G61-2 (SS-) | Sensor is covered with a cloth | Below 0.8 V |
The connection procedure for using a digital tester such as a TOYOTA electrical tester is shown above. When using an analog tester, connect the negative (-) lead to terminal 3 and the positive (+) lead to terminal 6 of the cooler thermistor (solar sensor).
Do not bring the positive and negative tester probes too close to each other as a short circuit may occur.
Use an incandescent light for inspection. Bring it within about 30 cm (11.8 in.) of the cooler thermistor (solar sensor).
As the inspection light is moved away from the sensor, the voltage decreases.
| *a | Component with harness connected
(Cooler Thermistor (Solar Sensor)) |
OK
NG
Disconnect the G34 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G61-1 (SS+) - G34-30 (S5-4) | Always | Below 1 Ω |
| G61-2 (SS-) - G34-33 (TS) | Always | Below 1 Ω |
| G61-1 (SS+) - Body ground | Always | 10 kΩ or higher |
| G61-2 (SS-) - Body ground | Always | 10 kΩ or higher |
OK
NG