Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING › 2014.12–2017.06
RM2170E _58 Vehicle Interior _057044 INTERIOR PANELS / TRIM _0278146 ROOF HEADLINING A

INTERIOR PANELS / TRIM  ROOF HEADLINING  REASSEMBLY  


PROCEDURE

Hide 82171 1.INSTALL NO. 1 ROOF WIRE (w/o Room Light)

a.

Align the positioning tape (Red) on the front part of the No. 1 roof wire with the front tab of the roof headlining.

B387604E01
1.628,2.221 1.785,2.370 0.157,0.149 10 *a 1.312,2.175 1.628,2.285 false

Text in Illustration
V100144

Positioning Tape (Red)
V100145

Positioning Tape
V100155

Adhesive Tape - -
*a Marking - -


b.

Align the No. 1 roof wire positioning tape with the markings on the roof headlining.


c.

Install the No. 1 roof wire to the roof headlining with the adhesive tape.

NOTICE:
·

Apply the tape securely in place.

·

Do not touch the adhesive surface when applying the tape to prevent adhesion failure.




Hide 82171 2.INSTALL NO. 1 ROOF WIRE (w/ Room Light)

a.

Align the positioning tape (Red) on the front part of the No. 1 roof wire with the front tab of the roof headlining.

B387602E01
1.582,2.141 1.740,2.290 0.157,0.149 10 *a 1.158,2.106 1.569,2.206 false

Text in Illustration
V100144

Positioning Tape (Red)
V100145

Positioning Tape
V100155

Adhesive Tape - -
*a Marking - -


b.

Align the No. 1 roof wire positioning tape with the markings on the roof headlining.


c.

Install the No. 1 roof wire to the roof headlining with the adhesive tape.

NOTICE:
·

Apply the tape securely in place.

·

Do not touch the adhesive surface when applying the tape to prevent adhesion failure.




Hide 63359 3.INSTALL ROOF HEADLINING END PAD

a.

Remove the release paper from 2 new roof headlining end pads.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



b.
B301172E02
0.168,1.631 0.325,1.780 0.157,0.149 10 *a 0.341,1.716 0.725,1.639 false

Align the 2 roof headlining end pads with the markings on the roof headlining and install the pads as shown in the illustration.

Text in Illustration
*a Marking


Hide 63387 4.INSTALL ROOF HEADLINING FORMING PAD

a.

Remove the release paper from 2 new roof headlining forming pads.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



b.
B387585E01
0.208,0.923 0.366,1.072 0.157,0.149 10 *a 0.207,1.172 0.322,1.274 false 0.789,1.736 1.091,2.025 1.091,2.025 0.373,1.748 false 0.033,1.072 0.190,1.220 0.157,0.149 10 *a 1.104,1.938 1.262,2.087 0.157,0.149 10 *a 0.382,1.02 0.754,1.259 false

Align the 2 roof headlining forming pads with the markings on the roof headlining and install the pads as shown in the illustration.

Text in Illustration
*a Marking


Hide 66425B 5.INSTALL REAR NO. 2 SIDE RAIL SPACER LH

a.
B308238E04
2.344,0.927 2.656,1.271 false 1.719,1 1.948,1.344 false 1.083,1.344 1.302,1.688 false 0.406,1.052 0.771,1.104 false 0.219,0.969 0.406,1.135 0.188,0.167 10 true *b 1.948,1.385 2.167,1.552 0.219,0.167 10 true *a 2.625,1.292 2.833,1.458 0.208,0.167 10 false *a 1.26,1.708 1.458,1.885 0.198,0.177 10 true *a

Align a new rear No. 2 side rail spacer LH with the markings on the roof headlining and install the spacer using hot-melt glue as shown in the illustration.

Text in Illustration
*a Hot-melt Glue
*b Marking


Hide 66414A 6.INSTALL REAR NO. 2 SIDE RAIL SPACER RH

HINT:

Use the same procedure as for the LH side.


Hide 63343 7.INSTALL NO. 3 ROOF SILENCER PAD

a.

Align a new No. 3 roof silencer pad with the markings on the roof headlining and install the pad using hot-melt glue as shown in the illustration.

B392185E02
6.802,0.396 6.927,0.635 false 4.917,1.396 5.281,1.552 false 3.438,1.75 3.802,1.917 false 6.865,0.635 7.021,0.781 0.156,0.146 10 false *b 6.156,0.281 6.271,0.427 0.115,0.146 10 false A 6.625,0.719 6.74,0.865 0.115,0.146 10 false A 5.292,1.5 5.448,1.646 0.156,0.146 10 true *b 3.281,1.688 3.438,1.833 0.156,0.146 10 true *a

Text in Illustration
*a Hot-melt Glue *b Marking

Standard Measurement:
Dimension Measurement
A 20 mm (0.787 in.)



Hide 63342 8.INSTALL NO. 2 ROOF SILENCER PAD (w/o Room Light)

a.

Align a new No. 2 roof silencer pad and with the markings on the roof headlining and install the pad using hot-melt glue as shown in the illustration.

B443909E02
2.188,1.5 2.542,1.469 false 3.688,1.917 4.271,2.031 false 1.24,0.469 1.333,0.635 false 0.604,0.344 0.948,0.635 0.344,0.292 10 false A 1.281,0.667 1.625,0.958 0.344,0.292 10 false *b 4.292,1.969 4.5,2.167 0.208,0.198 10 true *a 2,1.427 2.198,1.615 0.198,0.188 10 true *b 1.042,0.771 1.385,1.063 0.344,0.292 10 false A

Text in Illustration
*a Hot-melt Glue *b Marking

Standard Measurement:
Dimension Measurement
A 20 mm (0.787 in.)



Hide 63342 9.INSTALL NO. 2 ROOF SILENCER PAD (w/ Room Light)

a.

Align a new No. 2 roof silencer pad with the markings on the roof headlining and install the pad using hot-melt glue as shown in the illustration.

B392181E01
0.466,0.674 0.582,0.823 0.116,0.149 10 A 0.868,0.272 0.983,0.421 0.116,0.149 10 A 0.83,0.581 0.987,0.730 0.157,0.149 10 *b 4.722,2.132 4.879,2.281 0.157,0.149 10 *a 2.29,1.345 2.447,1.494 0.157,0.149 10 *b 0.395,0.363 0.83,0.643 false 2.435,1.41 2.83,1.571 false 3.958,1.893 4.718,2.202 false

Text in Illustration
*a Hot-melt Glue *b Marking

Standard Measurement:
Dimension Measurement
A 20 mm (0.787 in.)



Hide 63341 10.INSTALL NO. 1 ROOF SILENCER PAD

a.
B392179E01
0.482,0.216 0.639,0.365 0.157,0.149 10 *a 1.199,0.761 1.315,0.910 0.116,0.149 10 A 1.716,0.266 1.832,0.415 0.116,0.149 10 A 0.664,0.299 1.105,0.392 false

Align a new No. 1 roof silencer pad with the markings on the roof headlining and install the pad using hot-melt glue as shown in the illustration.

Text in Illustration
*a Marking

Standard Measurement:
Dimension Measurement
A 20 mm (0.787 in.)



Hide 63341D 11.INSTALL FRONT ROOF SILENCER PAD

a.
B392177E01
2.772,0.216 2.929,0.365 0.157,0.149 10 *a 1.525,0.264 1.641,0.413 0.116,0.149 10 A 2.045,0.796 2.161,0.945 0.116,0.149 10 A 2.259,0.437 2.766,0.301 false

Align 2 new roof headlining silencer pads with the markings on the roof headlining and install the pads using hot-melt glue as shown in the illustration.

Text in Illustration
*a Marking

Standard Measurement:
Dimension Measurement
A 20 mm (0.787 in.)



Hide 73137A 12.INSTALL UPPER SHOULDER BELT ANCHOR COVER

a.
B297740

Install the rear seat shoulder belt cover RH to the roof headlining.


b.

Engage the 4 claws to install the seat belt anchor cover.


Hide 86101J 13.INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY

Hide 86730C 14.INSTALL AMPLIFIER MICROPHONE ASSEMBLY

Hide 63359B 15.INSTALL ROOF HEADLINING RETAINER COVER