Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › 2011.12–2017.06
RM2170E _59 Vehicle Exterior _057045 WINDOW / GLASS _0278147 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Driver Side Power Window Auto Up / Down Function does not Operate with Power Window Master Switch  


DESCRIPTION

If the manual up and down functions operate normally but the auto up and down functions do not, then fail-safe mode may be functioning.

If power window initialization (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION) has not been performed, the auto up and down functions will not operate.

WIRING DIAGRAM

B281016E18
0.269,2.289 2.276,2.705 2.008,0.415 10 Main Body ECU (Multiplex Network Body ECU) 0.965,3.368 2.611,3.524 1.647,0.156 10 : LIN Communication Line 0.415,0.529 1.321,0.869 0.906,0.340 10 from Auxiliary Battery 1.852,0.669 2.464,0.825 0.612,0.156 10 DOOR D 2.52,2.41 4.574,2.816 2.054,0.406 10 Power Window Regulator Motor Assembly (for Driver Door) 5.228,2.406 6.838,2.765 1.610,0.360 10 Power Window Regulator Master Switch Assembly 2.52,2.251 3.527,2.412 1.008,0.161 10 J3*1, H3*2 5.228,2.247 5.951,2.407 0.723,0.161 10 J1*1, H1*2 1.635,1.589 2.015,1.745 0.380,0.156 10 LIN2 2.833,1.449 3.095,1.605 0.262,0.156 10 LIN 2.833,0.426 2.962,0.582 0.129,0.156 10 B 3.799,0.426 4.206,0.582 0.407,0.156 10 AUTO 5.373,0.524 5.798,0.680 0.426,0.156 10 AUTO 5.373,1.033 5.507,1.189 0.134,0.156 10 D 5.373,1.528 5.507,1.684 0.134,0.156 10 U 5.373,1.832 5.507,1.988 0.134,0.156 10 E 3.724,0.93 4.238,1.086 0.514,0.156 10 DOWN 3.962,1.44 4.207,1.595 0.245,0.156 10 UP 3.87,1.729 4.237,1.885 0.367,0.156 10 GND 4.252,1.729 4.381,1.885 0.129,0.156 10 1 4.252,0.935 4.381,1.091 0.129,0.156 10 7 5.209,0.935 5.338,1.091 0.129,0.156 10 5 4.821,1.458 5.321,1.614 0.500,0.156 10 8*1,1*2 4.821,1.748 5.307,1.904 0.486,0.156 10 1*1,9*2 4.252,0.426 4.381,0.582 0.129,0.156 10 4 5.209,0.426 5.338,0.582 0.129,0.156 10 4 4.252,1.449 4.437,1.605 0.185,0.156 10 10 2.641,0.426 2.770,0.582 0.129,0.156 10 2 2.633,1.449 2.804,1.605 0.172,0.156 10 9 3.299,3.157 4.083,3.313 0.784,0.156 10 *1: for LHD 3.299,3.442 4.083,3.598 0.784,0.156 10 *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

The power window control system uses a LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the power window control system after confirming that the communication system is functioning properly.

·

If a power window regulator motor assembly has been replaced with a new one, initialize the power window control system (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).

·

When the ECU determines that the power window regulator motor assembly (for driver door) has a malfunction, DTC B2311 is stored.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (DRIVER DOOR WINDOW MOTOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch to on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / D-Door Motor / Data List.


e.

Read the Data List according to the display on the intelligent tester.

D-Door Motor (Power Window Regulator Motor Assembly (for Driver Door))
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D Door P/W Auto SW Driver door power window auto switch signal / ON or OFF ON: Driver door power window auto switch operated
OFF: Driver door power window auto switch not operated
-

OK:

On the intelligent tester screen, ON or OFF is displayed accordingly.




OK

2.PERFORM INITIALIZATION (DRIVER DOOR WINDOW MOTOR)

NG

4.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
2.PERFORM INITIALIZATION (DRIVER DOOR WINDOW MOTOR)
a.

Initialize the power window regulator motor assembly (for driver door) (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).



NEXT

3.CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP/DOWN FUNCTION)
3.CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP/DOWN FUNCTION)
a.

Check that the driver door power window moves when the auto up and down functions of the power window regulator master switch assembly are operated (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK).


OK:

Driver door auto up and down functions are normal.



OK

END (PROBLEM DUE TO INITIALIZATION FAILURE)

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR)

4.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.
B298969E46
1.073,0.844 1.115,1.656 false 2.344,0.844 2.313,1.656 false 1.688,1.802 1.469,2.646 false 1.865,1.802 2.094,2.667 false 1.25,1.802 0.948,2.708 false 0.198,0.083 0.385,0.271 0.188,0.188 10 false *a 0.938,0.646 1.24,0.833 0.302,0.188 10 false E*B 2.094,0.656 2.677,0.844 0.583,0.188 10 false E*A,U*B 0.792,2.708 1.083,2.896 0.292,0.188 10 false U*A 1.385,2.667 1.542,2.854 0.156,0.188 10 false D 1.948,2.677 2.385,2.865 0.438,0.188 10 false AUTO

Remove the power window regulator master switch assembly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Switch Condition Specified Condition
8 (U) - 1 (E) Auto UP Below 1 Ω
4 (AUTO) - 1 (E) Auto UP Below 1 Ω
5 (D) - 1 (E) Auto DOWN Below 1 Ω
4 (AUTO) - 1 (E) Auto DOWN Below 1 Ω

for RHD
Tester Connection Switch Condition Specified Condition
1 (U) - 9 (E) Auto UP Below 1 Ω
4 (AUTO) - 9 (E) Auto UP Below 1 Ω
5 (D) - 9 (E) Auto DOWN Below 1 Ω
4 (AUTO) - 9 (E) Auto DOWN Below 1 Ω


Text in Illustration
*A for LHD
*B for RHD
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)



OK

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - POWER WINDOW REGULATOR MOTOR (FOR DRIVER DOOR))

NG

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - POWER WINDOW REGULATOR MOTOR (FOR DRIVER DOOR))
a.

Disconnect the power window regulator motor assembly (for driver door) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
J1-4 (AUTO) - J3-4 (AUTO) Always Below 1 Ω
J1-4 (AUTO) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
H1-4 (AUTO) - H3-4 (AUTO) Always Below 1 Ω
H1-4 (AUTO) - Body ground Always 10 kΩ or higher




OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR