Use the following procedure to troubleshoot the power window control system.
*: Use the intelligent tester.
| Proceed to |
|---|
| NEXT |
NEXT
In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
The following 5 items are important points in the problem analysis:
| What | Vehicle model, system name |
| When | Date, time, occurrence frequency |
| Where | Road conditions |
| Under what conditions? | Driving conditions, weather conditions |
| How did it happen? | Problem symptoms |
| Proceed to |
|---|
| NEXT |
NEXT
Measure the auxiliary battery voltage with the power switch off.
11 to 14 V
If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.
Check the fuses and relays.
Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.
| Proceed to |
|---|
| NEXT |
NEXT
Use the intelligent tester to check if the LIN communication system is functioning normally (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| No DTCs output | A |
| DTCs output | B |
A
B
(See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
Check for DTCs and note any codes that are output (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DTC CHECK / CLEAR).
Clear the DTCs.
Recheck for DTCs.
| Result | Proceed to |
|---|---|
| No DTCs output | A |
| DTCs output | B |
A
B
(See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART)
Refer to Problem Symptoms Table (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).
| Result | Proceed to |
|---|---|
| Fault is not listed in problem symptoms table | A |
| Fault is listed in problem symptoms table | B |
A
B
Operation Check (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK)
Terminals of ECU (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>TERMINALS OF ECU)
Data List / Active Test (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST)
| Proceed to |
|---|
| NEXT |
NEXT
Check if driver door window regulator, power window regulator motor assembly (for driver door), door glass or door glass run has been removed and reinstalled.
| Result | Proceed to |
|---|---|
| Driver door window regulator, power window regulator motor assembly (for driver door), door glass or door glass run has been removed and reinstalled. | A |
| None of the driver door window regulator, power window regulator motor assembly (for driver door), door glass or door glass run has been removed and reinstalled. | B |
A
B
If the driver door window regulator or power window regulator motor assembly (for driver door) have been removed and reinstalled, perform "Initialize Power Window Control System" (initialization of the pulse sensor) for the driver door glass (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).
If "Initialize Power Window Control System" (initialization of the pulse sensor) has not been performed, the auto operation function, jam protection function and key-off operation function will not operate or will operate incorrectly.
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT