When the rear window defogger switch on the air conditioning panel (heater control switch board) is pressed, the operation signal is transmitted to the air conditioning amplifier assembly through a LIN communication line. When the air conditioning amplifier assembly receives the signal, it turns on the defogger relay to operate the rear window defogger.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
If the auxiliary battery voltage becomes low, rear window defogger operation is canceled to prioritize supplying power to the power steering system.
Check the air conditioning system.
Both the window defogger system operation signal and air conditioning system operation signal are transmitted to the air conditioning amplifier assembly through the same communication line.
The air conditioning system operates normally.
OK
NG
Connect the intelligent tester to the DLC3.
Turn the power switch to on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Air Conditioner / Active Test.
Perform the Active Test according to the display on the intelligent tester.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Defogger Relay (Rear) | Rear window defogger | OFF or ON | - |
The rear window defogger system operates normally.
OK
NG
Temporarily replace the air conditioning amplifier assembly with a new or known good one (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL).
Check that the rear window defogger system operates normally.
The rear window defogger system operates normally.
OK
NG
Inspect the defogger relay (See page Vehicle Exterior>WINDOW / GLASS>RELAY>ON-VEHICLE INSPECTION).
OK
NG
Remove the defogger relay from the engine room relay block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Defogger relay holder terminal-1 - Body ground | Power switch on (IG) | 11 to 14 V |
| Defogger relay holder terminal-5 - Body ground | Always | 11 to 14 V |
| *1 | NO. 2 Engine Room Relay Block and NO. 2 Junction Block Assembly |
| *2 | Defogger Relay Holder |
OK
NG
Disconnect the G34 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Defogger relay holder terminal-2 - G34-38 (RDFG) | Always | Below 1 Ω |
| Defogger relay holder terminal-2 - Body ground | Always | 10 kΩ or higher |
| *1 | NO. 2 Engine Room Relay Block and NO. 2 Junction Block Assembly |
| *2 | Defogger Relay Holder |
OK
NG
Reconnect the G34 air conditioning amplifier assembly connector.
Reinstall the defogger relay.
Remove the air conditioning amplifier assembly with its connectors still connected (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G34-38 (RDFG) - G34-14 (GND) | Power switch on (IG)
Rear window defogger switch ON |
Below 1 V |
| G34-38 (RDFG) - G34-14 (GND) | Power switch on (IG)
Rear window defogger switch OFF |
11 to 14 V |
| *a | Component with harness connected
(Air Conditioning Amplifier Assembly) |
OK
NG
Disconnect the S1 and U1 back door glass (rear window defogger) connectors.
Remove the defogger relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S1-1 - Defogger relay holder terminal-3 | Always | Below 1 Ω |
| U1-1 - Body ground | Always | Below 1 Ω |
| S1-1 - Body ground | Always | 10 kΩ or higher |
| *1 | NO. 2 Engine Room Relay Block and NO. 2 Junction Block Assembly |
| *2 | Defogger Relay Holder |
OK
NG