Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS
RM2170E _59 Vehicle Exterior _057045 WINDOW / GLASS _0278156 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  REMOVAL  


PROCEDURE

Hide 1.REMOVE ROOF HEADLINING ASSEMBLY

Hide 56111 2.REMOVE WINDSHIELD GLASS SUB-ASSEMBLY

a.
B296182E02
0.363,0.329 0.585,0.546 0.223,0.217 10 *1 0.872,0.667 0.554,0.426 false

Apply protective tape to the area around the installation position of the windshield glass on the vehicle body to prevent it from being scratched.

Text in Illustration
*1 Protective Tape


b.
B296204E03
0.333,1.167 0.25,1.583 false 1.833,1.229 2.344,1.667 false 2.438,0.688 2.729,0.979 false 0.167,1.615 0.375,1.844 0.208,0.229 10 false *1 2.406,1.615 2.615,1.844 0.208,0.229 10 false *2 2.823,0.958 3.031,1.188 0.208,0.229 10 false *3

Using a knife, cut off the moulding as shown in the illustration.

Text in Illustration
*1 Windshield Glass
*2 Moulding
*3 Body


c.
B296183E02
1.677,0.26 1.417,0.26 1.417,0.26 1.417,0.688 true 1.677,0.552 1.417,0.552 false 1.333,0.719 1.521,0.906 0.188,0.188 10 false *1

Place matchmarks on the windshield glass sub-assembly and vehicle body on the locations indicated in the illustration.

Text in Illustration
*1 Matchmark

HINT:

Matchmarks are not necessary if the windshield glass sub-assembly is not going to be reused.



d.
B296185E03
2.229,0.521 1.719,0.844 1.719,0.844 1.229,0.521 true 1.729,1.302 1.729,1.479 false 1.635,0.896 1.813,1.073 0.177,0.177 10 false *1 1.656,1.51 1.833,1.688 0.177,0.177 10 false *2

Pass a piano wire between the vehicle body and glass from the interior.

Text in Illustration
*1 Windshield Glass Stopper
*2 Piano Wire


e.

Tie both wire ends to wooden blocks or similar objects that can serve as handles.


f.

Cut off the adhesive by pulling the piano wire around the windshield glass sub-assembly.

NOTICE:
·

When separating the windshield glass sub-assembly, be careful not to damage the paint or interior and exterior ornaments.

·

To prevent the safety pad from being scratched when removing the windshield glass, place a plastic sheet between the piano wire and safety pad.




g.

Disconnect the windshield glass stoppers.

B296186E02
1.635,0.969 1.458,0.99 false 4.688,0.792 4.5,0.927 false 4.833,0.927 4.833,1.073 4.833,1.073 5.229,1.073 false 4.979,0.875 4.979,1.073 false 5.094,0.938 5.094,1.073 false 1.302,0.927 1.479,1.094 0.177,0.167 10 false *1 5.25,0.969 5.427,1.135 0.177,0.167 10 false *1 4.333,0.865 4.51,1.031 0.177,0.167 10 false *2 0.896,0.177 1.073,0.344 0.177,0.167 10 false *A 4.167,0.177 4.344,0.344 0.177,0.167 10 false *B

Text in Illustration
*A 1-piece Type *B 2-pieceType
*1 No. 1 Windshield Glass Stopper *2 No. 2 Windshield Glass Stopper

NOTICE:
·

There are No. 1 and No. 2 stoppers on the windshield glass as shown in the illustration. Be careful not to damage the windshield glass when cutting off the adhesive.

·

To prevent the windshield glass from falling when performing this operation, be sure to hold the windshield glass using suction cups.



HINT:

Depending on the vehicle, either 1-piece or 2-piece type stoppers may be present.



h.

Using suction cups, remove the windshield glass sub-assembly.

NOTICE:
·

Be careful not to drop the windshield glass sub-assembly.

·

Leave as much adhesive on the vehicle body as possible when removing the windshield glass sub-assembly.




Hide 56117A 3.REMOVE WINDOW GLASS ADHESIVE DAM

a.

When reusing the windshield glass:

i.
B296187E02
0.139,0.062 0.351,0.248 0.212,0.186 10 *A

Using a scraper, remove the window glass adhesive dam.

Text in Illustration
*A Back Side

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the window glass adhesive dam with a new one.





Hide 4.REMOVE WINDSHIELD OUTSIDE MOULDING

a.

When reusing the windshield glass:

i.
B296188E02
0.139,0.062 0.351,0.248 0.212,0.186 10 *A

Using a scraper, remove the windshield outside moulding.

Text in Illustration
*A Back Side

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the windshield outside moulding with a new one.





Hide 5.REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 1-piece Type)

a.

When reusing the windshield glass:

i.
B296189E01
0.139,0.062 0.351,0.248 0.212,0.186 10 *A

Using a scraper, remove the 2 No. 1 windshield glass stoppers.

Text in Illustration
*A Back Side

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the 1-piece type No. 1 windshield glass stoppers with a new pair of 2-piece type No. 1 and No. 2 windshield glass stoppers.





Hide 56116C 6.REMOVE NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type)

a.

When reusing the windshield glass:

i.
B296189E01
0.139,0.062 0.351,0.248 0.212,0.186 10 *A

Using a scraper, remove the 2 No. 2 windshield glass stoppers.

Text in Illustration
*A Back Side

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the No. 2 windshield glass stoppers with new ones.





Hide 56115A 7.REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)

a.
B296190

Remove the 2 No. 1 windshield glass stoppers.

NOTICE:

Be sure to replace the No. 1 windshield glass stoppers with new ones.



Hide 8.CLEAN WINDSHIELD GLASS

a.

When reusing the windshield glass:

i.
B149736

Using a scraper, remove any adhesive dam and adhesive residue from the windshield glass.

NOTICE:

Be careful not to damage the windshield glass.



ii.

Clean the outer circumference of the windshield glass with a non-residue solvent.

NOTICE:
·

Do not touch the windshield glass surface after cleaning it.

·

Even if using a new windshield glass, clean the windshield glass with a non-residue solvent.





Hide 9.CLEAN VEHICLE BODY

a.
B296195E01
0.72,1.631 0.946,1.783 0.226,0.152 10 *1 0.579,1.412 0.783,1.631 false 0.807,0.903 0.557,0.472 0.557,0.472 0.423,0.472 false 0.22,0.387 0.446,0.539 0.226,0.152 10 *2

Clean and shape the contact surfaces of the vehicle body.

Text in Illustration
*1 Body
*2 Adhesive

i.

Using a knife, cut away excess adhesive on the contact surfaces of the vehicle body as shown in the illustration.

NOTICE:

Be careful not to damage the vehicle body.


HINT:

Leave as much adhesive on the vehicle body as possible.



ii.

Clean the contact surfaces of the vehicle body with a piece of cloth saturated with cleaner.

HINT:

Even if all the adhesive has been removed, clean the vehicle body.