Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING › 2011.12–2013.12
RM2170E _58 Vehicle Interior _057044 INTERIOR PANELS / TRIM _0278146 ROOF HEADLINING A

INTERIOR PANELS / TRIM  ROOF HEADLINING  REMOVAL  


PROCEDURE

Hide 71940A 4.REMOVE REAR SEAT HEADREST ASSEMBLY

Hide 71960B 5.REMOVE REAR CENTER SEAT HEADREST ASSEMBLY

Hide 67918A 9.REMOVE REAR DOOR SCUFF PLATE LH

a.
B300785

Disengage the 5 claws and guide and remove the rear door scuff plate LH.


Hide 67914 10.REMOVE FRONT DOOR SCUFF PLATE LH

a.
B300786

Disengage the 8 claws and remove the front door scuff plate LH.


Hide 62112 11.REMOVE COWL SIDE TRIM BOARD LH

a.
B300787

Remove the clip.


b.

Disengage the clip and remove the cowl side trim board LH.


Hide 62312B 12.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

a.

Remove the front door opening trim weatherstrip LH.


Hide 62212 13.REMOVE FRONT PILLAR GARNISH LH

a.
E276150E01
2.261,0.668 2.465,0.817 0.205,0.149 10 *1 2.562,0.35 2.445,0.668 false

Pull the upper part of the garnish toward the inside of the cabin and disengage the garnish from the base of the 2 clips.

Text in Illustration
*1 Front Pillar Garnish Clip

HINT:

Let the front pillar garnish LH hang down from the front pillar garnish clip.



b.
E276147E04
2.604,0.844 2.635,1.052 false 2.51,2.74 2.75,2.917 0.24,0.177 10 true (3) 0.302,0.125 0.542,0.302 0.24,0.177 10 false (1) 0.156,0.885 0.396,1.063 0.24,0.177 10 false *a 2.552,1.052 2.792,1.229 0.24,0.177 10 false *b 2.604,0.125 2.844,0.302 0.24,0.177 10 false (2)

Using needle-nose pliers with the tips wrapped with protective tape, rotate the front pillar garnish clip 90° in the direction indicated by the arrow (1) shown in the illustration.

Text in Illustration
*a 90°
*b Protective Tape


c.

Pull the front pillar garnish LH in the direction indicated by the arrow (2) shown in the illustration to disengage it from the front pillar garnish clip.

NOTICE:
·

If the front pillar garnish clip is not removed from the vehicle body and is not damaged, the front pillar garnish clip can be reused.

·

If the front pillar garnish clip is removed from the vehicle body, make sure to replace it with a new one.




d.

Pull the front pillar garnish LH in the direction indicated by the arrow (3) shown in the illustration to disengage the 2 guides to remove the front pillar garnish LH.


e.
B300790E02
1.51,2.458 1.594,2.167 false 2.396,1.99 1.896,2.073 false 0.688,1.688 1.052,1.563 false 3.094,0.5 3.177,0.708 false 2.375,1.01 2.26,0.802 false 2.604,1.219 2.469,1.521 true 3.01,1.521 2.938,1.198 true 2.438,1.896 2.656,2.083 0.219,0.188 10 true *2 0.5,1.635 0.781,1.833 0.281,0.198 10 false *3 1.417,2.51 1.615,2.708 0.198,0.198 10 true *1 3.083,0.708 3.24,0.854 0.156,0.146 10 false *1 2.083,0.719 2.24,0.865 0.156,0.146 10 false *1 2.948,1.542 3.135,1.729 0.188,0.188 10 true *2 2.365,1.542 2.563,1.719 0.198,0.177 10 true *3

Protect the curtain shield airbag assembly.

Text in Illustration
*1 Adhesive Tape
*2 Protective Cover
*3 Curtain Shield Airbag Assembly

i.

Cover the airbag with a piece of cloth or nylon and secure the edges of the cover with tape as shown in the illustration.

NOTICE:

Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.




Hide 62332A 14.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

a.

Remove the rear door opening trim weatherstrip LH.


Hide 73233C 15.REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side)

Hide 73220 16.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

Hide 62414A 17.REMOVE CENTER PILLAR LOWER GARNISH LH

a.
B300794

Disengage the 4 claws and 2 clips, and remove the center pillar lower garnish LH.


Hide 62412B 18.REMOVE CENTER PILLAR UPPER GARNISH LH

a.
B300793

Remove the 2 screws and disengage the clip.


b.

Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar upper garnish LH and remove the center pillar upper garnish LH.


Hide 67917A 19.REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 67913 20.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 62111C 21.REMOVE COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure as for the LH side.


Hide 62311B 22.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 62211 23.REMOVE FRONT PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 62331A 24.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 73233 25.REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side)

HINT:

Use the same procedure as for the LH side.


Hide 73210 26.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 62413A 27.REMOVE CENTER PILLAR LOWER GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 62411B 28.REMOVE CENTER PILLAR UPPER GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 58410B 29.REMOVE DECK BOARD ASSEMBLY

a.

Remove the deck board assembly.


Hide 64997 30.REMOVE DECK FLOOR BOX LH

a.

Remove the deck floor box LH.


Hide 64995 31.REMOVE DECK FLOOR BOX RH

HINT:

Use the same procedure as for the LH side.


Hide 64330D 32.REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY

a.

Remove the package tray trim panel assembly.


Hide 64716D 33.REMOVE REAR DECK TRIM COVER

a.
B297727

Remove the 2 clips.


b.

Disengage the 4 claws and 2 guides, and remove the rear deck trim cover.


Hide 73370 34.DISCONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH

Hide 58732C 35.REMOVE REAR ABSORBER CAP LH

a.
B300796

Disengage the 2 claws and 2 guides, and remove the rear absorber cap LH.


Hide 81330 36.REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY

Hide 64740C 37.REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

a.

Turn the rear seatback hinge in the direction indicated by the arrow shown in the illustration.

B300799E02
2.625,3.563 2.865,3.521 false 2.875,3.448 3.063,3.615 0.188,0.167 10 true *1

Text in Illustration
*1 Rear Seatback Hinge - -


b.

Remove the bolt and 2 screws.


c.

Disengage the 4 claws, 4 clips and guide, and remove the deck trim side panel assembly LH.


Hide 62472A 38.REMOVE ROOF SIDE INNER GARNISH LH

a.

Disengage the 5 clips.

B443911


b.

Pass the floor anchor of the rear seat 3 point type outer belt assembly LH through the roof side inner garnish LH and remove the roof side inner garnish LH.


Hide 73360 39.DISCONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 58731C 40.REMOVE REAR ABSORBER CAP RH

HINT:

Use the same procedure as for the LH side.


Hide 64730B 41.REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 73350 42.DISCONNECT REAR CENTER SEAT LAP TYPE BELT ASSEMBLY

Hide 62471A 43.REMOVE ROOF SIDE INNER GARNISH RH

a.
B299306

Using a moulding remover, disengage the 4 claws and guide, and disconnect the belt guide.


b.

Disengage the 5 clips.

B443908


c.

Pass the floor anchor of the rear seat 3 point type outer belt assembly RH through the roof side inner garnish RH and remove the roof side inner garnish RH.


Hide 81260A 44.REMOVE MAP LIGHT ASSEMBLY

Hide 74610S 45.REMOVE ASSIST GRIP ASSEMBLY

HINT:

Use the same procedure to remove all assist grips.


a.
B175478

Using a moulding remover, disengage the 4 claws and remove the 2 assist grip covers.


b.
B175479

Disengage the 2 clips and remove the assist grip.


Hide 74320 46.REMOVE VISOR ASSEMBLY LH

a.
B300801

Disconnect the visor shaft from the visor holder.


b.

Remove the 2 screws and the visor assembly LH.


Hide 74310 47.REMOVE VISOR ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 74348 48.REMOVE VISOR HOLDER

a.
B151362E04
1.109,0.296 1.355,0.443 0.246,0.147 10 45°

Turn the visor holder clockwise 45° and disengage the 2 claws to remove the visor holder.

HINT:

Use the same procedure for the LH side and RH side.



Hide 49.REMOVE ROOF HEADLINING ASSEMBLY

B297737E05
0.271,5.281 0.438,5.448 0.167,0.167 10 true *b 4.979,0.25 5.156,0.438 0.177,0.188 10 true *c 4.979,5.281 5.167,5.458 0.188,0.177 10 true *a 0.229,0.188 0.5,0.469 0.271,0.281 12 false *A

Text in Illustration
*A 1 Claw Type - -
*a Front Pillar RH Side *b Front Pillar LH Side
*c Rear Pillar RH Side - -

B335594E07
0.229,5.271 0.406,5.438 0.177,0.167 10 true *b 4.938,0.229 5.115,0.427 0.177,0.198 10 true *c 4.938,5.271 5.125,5.438 0.188,0.167 10 true *a 0.198,0.198 0.479,0.469 0.281,0.271 12 false *A

Text in Illustration
*A 2 Claws Type - -
*a Front Pillar RH Side *b Front Pillar LH Side
*c Rear Pillar RH Side - -

a.

for front pillar RH side:

i.

Disconnect the connector.


ii.

Using a clip remover, disengage the 3 clamps.



b.

for front pillar LH side:

i.

Disconnect the connector.


ii.

Using a clip remover, disengage the 3 clamps.



c.

for rear pillar RH side:

i.

Disconnect the connector.


ii.

Remove the bolt and disconnect the connector bracket.


iii.

Using a clip remover, disengage the 2 clamps.



d.

Using a clip remover, remove the 3 clips.


e.

Disengage the claw. (for 1 Claw Type)


f.

Disengage the 2 claws. (for 2 Claws Type)


g.
B301724

Remove the roof headlining assembly from the vehicle through the back door as shown in the illustration.

NOTICE:

Do not damage the roof headlining assembly or body interior.